On Fri, Dec 9, 2016 at 7:59 PM, Billy Shuman <wshum...@gmail.com> wrote:
> On Thu, Dec 8, 2016 at 4:03 AM, Siva Reddy Kallam
> <siva.kal...@broadcom.com> wrote:
>> On Thu, Dec 8, 2016 at 12:14 AM, Billy Shuman <wshum...@gmail.com> wrote:
>>> On Wed, Dec 7, 2016 at 12:37 PM, Michael Chan <michael.c...@broadcom.com>
>>> wrote:
>>>> On Wed, Dec 7, 2016 at 7:20 AM, Billy Shuman <wshum...@gmail.com> wrote:
>>>>> After resume on 4.9.0-rc8 tg3 is dead.
>>>>>
>>>>> In logs I see:
>>>>> kernel: tg3 0000:44:00.0: phy probe failed, err -19
>>>>> kernel: tg3 0000:44:00.0: Problem fetching invariants of chip, aborting
>>>>
>>>> -19 is -ENODEV which means tg3 cannot read the PHY ID.
>>>>
>>>> If it's a true suspend/resume operation, the driver does not have to
>>>> go through probe during resume. Please explain how you do
>>>> suspend/resume.
>>>>
>>>
>>> Sorry my previous message was accidentally sent to early.
>>>
>>> I used systemd (systemctl suspend) to suspend.
>>>
>> We need more information to proceed further.
>> Without suspend, Are you able to use the tg3 port?
>
> Yes the port works fine without suspend.
OK
>
>> Which Broadcom card are you having in laptop?
>
> The nic is a NetXtreme BCM57762 Gigabit Ethernet PCIe in a thunderbolt3 dock.
>
OK
>> Please provide complete tg3 specific logs in dmesg.
>>
>
> [ 32.084010] tg3.c:v3.137 (May 11, 2014)
> [ 32.124695] tg3 0000:44:00.0 eth0: Tigon3 [partno(BCM957762) rev
> 57766001] (PCI Express) MAC address 98:e7:f4:8b:13:19
> [ 32.124698] tg3 0000:44:00.0 eth0: attached PHY is 57765
> (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
> [ 32.124699] tg3 0000:44:00.0 eth0: RXcsums[1] LinkChgREG[0]
> MIirq[0] ASF[0] TSOcap[1]
> [ 32.124700] tg3 0000:44:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
> [ 32.219764] tg3 0000:44:00.0 enp68s0: renamed from eth0
> [ 36.219245] tg3 0000:44:00.0 enp68s0: Link is up at 1000 Mbps, full duplex
> [ 36.219250] tg3 0000:44:00.0 enp68s0: Flow control is on for TX and on for
> RX
> [ 36.219251] tg3 0000:44:00.0 enp68s0: EEE is disabled
>
> after resume
> [ 92.292838] tg3 0000:44:00.0 enp68s0: No firmware running
> [ 93.521744] tg3 0000:44:00.0: tg3_abort_hw timed out,
> TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
> [ 106.704655] tg3 0000:44:00.0 enp68s0: Link is down
> [ 108.370356] tg3 0000:44:00.0: tg3_abort_hw timed out,
> TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
>
> after rmmod, modprobe
> [ 570.933636] tg3 0000:44:00.0: tg3_abort_hw timed out,
> TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
> [ 604.847215] tg3.c:v3.137 (May 11, 2014)
> [ 605.010075] tg3 0000:44:00.0: phy probe failed, err -19
> [ 605.010077] tg3 0000:44:00.0: Problem fetching invariants of chip, aborting
>
>
>
>
We will try to reproduce and update you on this.
>>>> Did this work before? There has been very few changes to tg3 recently.
>>>>
>>>
>>> This is a new laptop for me, but the same behavior is seen on 4.4.36 and
>>> 4.8.12.
>>>
>>>>>
>>>>> rmmod and modprobe does not fix the problem only a reboot resolves the
>>>>> issue.
>>>>>
>>>>> Billy