On Sat, Jan 07, 2017 at 09:38:34AM +0000, Russell King - ARM Linux wrote:
> On Wed, Dec 28, 2016 at 05:46:27PM +0100, Thomas Petazzoni wrote:
> > @@ -6511,7 +6515,9 @@ static int mvpp2_port_probe(struct platform_device
> > *pdev,
> > dev_err(&pdev->dev, "failed to init port %d\n", id);
> > goto err_free_stats;
> > }
> > - mvpp2_port_power_up(port);
> > +
> > + if (priv->hw_version == MVPP21)
> > + mvpp21_port_power_up(port);
>
> This has the side effect that nothing clears the port reset bit in the
> GMAC, which means there's no hope of the interface working - with the
> reset bit set, the port is well and truely held in "link down" state.
>
> In any case, the GMAC part is much the same as mvneta, and I think
> that code should be shared rather than writing new versions of it.
> There are some subtle differences between neta, pp2.1 and pp2.2, but
> it's entirely doable (I have an implementation here as I wasn't going
> to duplicate this code for my phylink conversion.)
In addition to comphy configuration and the above, I also need the
following to have working SGMII. The change of MACMODE is needed
because uboot has configured the port for 10Gbase-R mode (it has a
10G PHY on it, but the PHY switches to SGMII in <10G modes.) The
GMAC control register 4 is needed to properly configure for SGMII
mode. I also included RGMII mode as well in there, as I expect you'd
need it to have GMAC properly configured for RGMII.
With this in place (and the other bits mentioned above), I can ping
the clearfog switch on the other end of eth0's cable:
# ping6 -I eth0 fe80::250:43ff:fe02:302
PING fe80::250:43ff:fe02:302(fe80::250:43ff:fe02:302) from fe80::200:ff:fe00:1
eth0: 56 data bytes
64 bytes from fe80::250:43ff:fe02:302: icmp_seq=1 ttl=64 time=0.297 ms
diff --git a/drivers/net/ethernet/marvell/mvpp2.c
b/drivers/net/ethernet/marvell/mvpp2.c
index bc97eebf7eee..4b6ec6213e9c 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -345,7 +345,17 @@
#define MVPP2_GMAC_TX_FIFO_MIN_TH_ALL_MASK 0x1fc0
#define MVPP2_GMAC_TX_FIFO_MIN_TH_MASK(v) (((v) << 6) & \
MVPP2_GMAC_TX_FIFO_MIN_TH_ALL_MASK)
+#define MVPP22_GMAC_CTRL_4_REG 0x90
+#define MVPP22_CTRL4_EXT_PIN_GMII_SEL BIT(0)
+#define MVPP22_CTRL4_DP_CLK_SEL BIT(5)
+#define MVPP22_CTRL4_SYNC_BYPASS BIT(6)
+#define MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE BIT(7)
+
+#define MVPP22_XLG_CTRL3_REG 0x11c
+#define MVPP22_XLG_CTRL3_MACMODESELECT_MASK (7 << 13)
+#define MVPP22_XLG_CTRL3_MACMODESELECT_GMAC (0 << 13)
+/* offsets from iface_base */
#define MVPP22_SMI_MISC_CFG_REG 0x2a204
#define MVPP22_SMI_POLLING_EN BIT(10)
@@ -4171,6 +4181,23 @@ static void mvpp2_port_mii_set(struct mvpp2_port *port)
{
u32 val;
+ if (port->priv->hw_version == MVPP22) {
+ val = readl(port->base + MVPP22_XLG_CTRL3_REG);
+ val &= ~MVPP22_XLG_CTRL3_MACMODESELECT_MASK;
+ val |= MVPP22_XLG_CTRL3_MACMODESELECT_GMAC;
+ writel(val, port->base + MVPP22_XLG_CTRL3_REG);
+
+ val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+ if (port->phy_interface == PHY_INTERFACE_MODE_RGMII)
+ val |= MVPP22_CTRL4_EXT_PIN_GMII_SEL;
+ else
+ val &= ~MVPP22_CTRL4_EXT_PIN_GMII_SEL;
+ val &= ~MVPP22_CTRL4_DP_CLK_SEL;
+ val |= MVPP22_CTRL4_SYNC_BYPASS;
+ val |= MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
+ writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
+ }
+
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
switch (port->phy_interface) {
--
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
