From: Kumar Sanghvi <[email protected]>

Add support for matching on vlan tci.  Construct vlan tci match param
based on vlan-id and vlan-pcp values supplied by tc.

Signed-off-by: Kumar Sanghvi <[email protected]>
Signed-off-by: Rahul Lakkireddy <[email protected]>
Signed-off-by: Ganesh Goudar <[email protected]>
---
 .../net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c   | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c 
b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c
index 647c86ae343d..f7554b768e9d 100644
--- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c
+++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c
@@ -160,6 +160,40 @@ static void cxgb4_process_flow_match(struct net_device 
*dev,
                fs->mask.tos = mask->tos;
        }
 
+       if (dissector_uses_key(cls->dissector, FLOW_DISSECTOR_KEY_VLAN)) {
+               struct flow_dissector_key_vlan *key, *mask;
+               u16 vlan_tci, vlan_tci_mask;
+
+               key = skb_flow_dissector_target(cls->dissector,
+                                               FLOW_DISSECTOR_KEY_VLAN,
+                                               cls->key);
+               mask = skb_flow_dissector_target(cls->dissector,
+                                                FLOW_DISSECTOR_KEY_VLAN,
+                                                cls->mask);
+               vlan_tci = key->vlan_id | (key->vlan_priority <<
+                                          VLAN_PRIO_SHIFT);
+               vlan_tci_mask = mask->vlan_id | (mask->vlan_priority <<
+                                                VLAN_PRIO_SHIFT);
+               fs->val.ivlan = cpu_to_be16(vlan_tci);
+               fs->mask.ivlan = cpu_to_be16(vlan_tci_mask);
+
+               /* Chelsio adapters use ivlan_vld bit to match vlan packets
+                * as 802.1Q. Also, when vlan tag is present in packets,
+                * ethtype match is used then to match on ethtype of inner
+                * header ie. the header following the vlan header.
+                * So, set the ivlan_vld based on ethtype info supplied by
+                * TC for vlan packets if its 802.1Q. And then reset the
+                * ethtype value else, hw will try to match the supplied
+                * ethtype value with ethtype of inner header.
+                */
+               if (fs->val.ethtype == ETH_P_8021Q) {
+                       fs->val.ivlan_vld = 1;
+                       fs->mask.ivlan_vld = 1;
+                       fs->val.ethtype = 0;
+                       fs->mask.ethtype = 0;
+               }
+       }
+
        /* Match only packets coming from the ingress port where this
         * filter will be created.
         */
@@ -179,6 +213,7 @@ static int cxgb4_validate_flow_match(struct net_device *dev,
              BIT(FLOW_DISSECTOR_KEY_IPV4_ADDRS) |
              BIT(FLOW_DISSECTOR_KEY_IPV6_ADDRS) |
              BIT(FLOW_DISSECTOR_KEY_PORTS) |
+             BIT(FLOW_DISSECTOR_KEY_VLAN) |
              BIT(FLOW_DISSECTOR_KEY_IP))) {
                netdev_warn(dev, "Unsupported key used: 0x%x\n",
                            cls->dissector->used_keys);
-- 
2.14.1

Reply via email to