Realtek PHYs implement the concept of so-called "extension pages". The
reason for this is probably because these PHYs expose more registers
than available in the standard address range.
After all read/write operations on such a page are done the driver
should switch back to page 0 where the standard MII registers (such as
MII_BMCR) are available.
When referring to such a register the datasheets of RTL8211E and
RTL8211F always specify:
- the page / "ext. page" which has to be written to RTL821x_PAGE_SELECT
- an address (sometimes also called reg)
These new utility functions make the existing code easier to read since
it removes some duplication (switching back to page 0 is done within the
new helpers for example).
No functional changes are intended.
Signed-off-by: Martin Blumenstingl <martin.blumensti...@googlemail.com>
---
drivers/net/phy/realtek.c | 83 ++++++++++++++++++++++++++++++-----------------
1 file changed, 53 insertions(+), 30 deletions(-)
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
index d6868e8daaab..5416ec5af042 100644
--- a/drivers/net/phy/realtek.c
+++ b/drivers/net/phy/realtek.c
@@ -41,6 +41,39 @@ MODULE_DESCRIPTION("Realtek PHY driver");
MODULE_AUTHOR("Johnson Leung");
MODULE_LICENSE("GPL");
+static int rtl8211x_page_read(struct phy_device *phydev, u16 page, u16 address)
+{
+ int ret;
+
+ ret = phy_write(phydev, RTL821x_PAGE_SELECT, page);
+ if (ret)
+ return ret;
+
+ ret = phy_read(phydev, address);
+
+ /* restore to default page 0 */
+ phy_write(phydev, RTL821x_PAGE_SELECT, 0x0);
+
+ return ret;
+}
+
+static int rtl8211x_page_write(struct phy_device *phydev, u16 page,
+ u16 address, u16 val)
+{
+ int ret;
+
+ ret = phy_write(phydev, RTL821x_PAGE_SELECT, page);
+ if (ret)
+ return ret;
+
+ ret = phy_write(phydev, address, val);
+
+ /* restore to default page 0 */
+ phy_write(phydev, RTL821x_PAGE_SELECT, 0x0);
+
+ return ret;
+}
+
static int rtl8201_ack_interrupt(struct phy_device *phydev)
{
int err;
@@ -63,31 +96,21 @@ static int rtl8211f_ack_interrupt(struct phy_device *phydev)
{
int err;
- phy_write(phydev, RTL821x_PAGE_SELECT, 0xa43);
- err = phy_read(phydev, RTL8211F_INSR);
- /* restore to default page 0 */
- phy_write(phydev, RTL821x_PAGE_SELECT, 0x0);
+ err = rtl8211x_page_read(phydev, 0xa43, RTL8211F_INSR);
return (err < 0) ? err : 0;
}
static int rtl8201_config_intr(struct phy_device *phydev)
{
- int err;
-
- /* switch to page 7 */
- phy_write(phydev, RTL821x_PAGE_SELECT, 0x7);
+ u16 val;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
- err = phy_write(phydev, RTL8201F_IER,
- BIT(13) | BIT(12) | BIT(11));
+ val = BIT(13) | BIT(12) | BIT(11);
else
- err = phy_write(phydev, RTL8201F_IER, 0);
+ val = 0;
- /* restore to default page 0 */
- phy_write(phydev, RTL821x_PAGE_SELECT, 0x0);
-
- return err;
+ return rtl8211x_page_write(phydev, 0x7, RTL8201F_IER, val);
}
static int rtl8211b_config_intr(struct phy_device *phydev)
@@ -118,41 +141,41 @@ static int rtl8211e_config_intr(struct phy_device *phydev)
static int rtl8211f_config_intr(struct phy_device *phydev)
{
- int err;
+ u16 val;
- phy_write(phydev, RTL821x_PAGE_SELECT, 0xa42);
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
- err = phy_write(phydev, RTL821x_INER,
- RTL8211F_INER_LINK_STATUS);
+ val = RTL8211F_INER_LINK_STATUS;
else
- err = phy_write(phydev, RTL821x_INER, 0);
- phy_write(phydev, RTL821x_PAGE_SELECT, 0);
+ val = 0;
- return err;
+ return rtl8211x_page_write(phydev, 0xa42, RTL821x_INER, val);
}
static int rtl8211f_config_init(struct phy_device *phydev)
{
int ret;
- u16 reg;
+ u16 val;
ret = genphy_config_init(phydev);
if (ret < 0)
return ret;
- phy_write(phydev, RTL821x_PAGE_SELECT, 0xd08);
- reg = phy_read(phydev, 0x11);
+ ret = rtl8211x_page_read(phydev, 0xd08, 0x11);
+ if (ret < 0)
+ return ret;
+
+ val = ret & 0xffff;
/* enable TX-delay for rgmii-id and rgmii-txid, otherwise disable it */
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
- reg |= RTL8211F_TX_DELAY;
+ val |= RTL8211F_TX_DELAY;
else
- reg &= ~RTL8211F_TX_DELAY;
+ val &= ~RTL8211F_TX_DELAY;
- phy_write(phydev, 0x11, reg);
- /* restore to default page 0 */
- phy_write(phydev, RTL821x_PAGE_SELECT, 0x0);
+ ret = rtl8211x_page_write(phydev, 0xd08, 0x11, val);
+ if (ret)
+ return ret;
return 0;
}
--
2.15.1
