Hi, i have a little problem with dlink dwl650+ pcmcia. After I downloaded wireless-2.6.git with cogito, compiled, rebooted my laptop and loaded the acx_pci module. But my pcmcia don't work. If i give this command line: # iwlist scanning eth1 Interface doesn't support scanning : Resource temporarily unavailable I tried with a 2.6.18-rc5 with tiacx and 2.6.17.13 with acx module, same result. The dmesg with tiacx module is: -- Sep 9 19:19:37 vinTux acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working fir mware upload. Report them Sep 9 19:19:37 vinTux running on a little-endian CPU Sep 9 19:19:37 vinTux PCI module v0.4.7 initialized, waiting for cards to probe... Sep 9 19:19:37 vinTux PCI: Enabling device 0000:02:00.0 (0000 -> 0003) Sep 9 19:19:37 vinTux ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Sep 9 19:19:37 vinTux PCI: Setting latency timer of device 0000:02:00.0 to 64 Sep 9 19:19:37 vinTux acx: found ACX100-based wireless network card at 0000:02:00.0, irq:11, phymem1:0x42010000, ph ymem2:0x42000000, mem1:0xfc994000, mem1_size:4096, mem2:0xfc9e0000, mem2_size:65536 Sep 9 19:19:37 vinTux initial debug setting is 0x000A Sep 9 19:19:37 vinTux using IRQ 11 Sep 9 19:19:37 vinTux requesting firmware image 'tiacx100c0D' Sep 9 19:19:37 vinTux acx: firmware image 'tiacx100c0D' was not provided. Check your hotplug scripts Sep 9 19:19:37 vinTux requesting firmware image 'tiacx100' Sep 9 19:19:38 vinTux acx_write_fw (main/combined):0 Sep 9 19:19:38 vinTux acx_validate_fw (main/combined):0 Sep 9 19:19:38 vinTux acx100_s_init_wep: writing WEP options Sep 9 19:19:38 vinTux initializing max packet templates Sep 9 19:19:38 vinTux unknown chip and EEPROM version combination (ACX100, v0), don't know how to parse config opti ons yet. Please report Sep 9 19:19:38 vinTux get_mask 0x00004D82, set_mask 0x00000000 Sep 9 19:19:38 vinTux got sensitivity value 64 Sep 9 19:19:38 vinTux got antenna value 0x08 Sep 9 19:19:38 vinTux got Energy Detect (ED) threshold 112 Sep 9 19:19:38 vinTux got Channel Clear Assessment (CCA) value 13 Sep 9 19:19:38 vinTux got regulatory domain 0x30 Sep 9 19:19:38 vinTux get_mask 0x00000000, set_mask 0x00000000 - after update Sep 9 19:19:38 vinTux new ratevector: 82 84 0B 16 2C Sep 9 19:19:38 vinTux setting RXconfig to 2010:0FDD Sep 9 19:19:38 vinTux acx: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x0D (Maxim), EEPROM version 0x00, u ploaded firmware 'Rev 1.9.10.0_A4' (0x01030505) Sep 9 19:19:38 vinTux creating /proc entry driver/acx_eth1 Sep 9 19:19:38 vinTux creating /proc entry driver/acx_eth1_diag Sep 9 19:19:38 vinTux creating /proc entry driver/acx_eth1_eeprom Sep 9 19:19:38 vinTux creating /proc entry driver/acx_eth1_phy Sep 9 19:19:38 vinTux acx v0.4.7: net device eth1, driver compiled against wireless extensions 20 Sep 9 19:19:39 vinTux acx_set_status(1):SCANNING Sep 9 19:19:39 vinTux updating initial settings on iface activation Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x0036EEFC Sep 9 19:19:39 vinTux important setting has been changed. Need to update packet templates, too Sep 9 19:19:39 vinTux updating packet templates Sep 9 19:19:39 vinTux updating Tx fallback to 1 retries Sep 9 19:19:39 vinTux updating transmit power: 18 dBm Sep 9 19:19:39 vinTux updating antenna value: 0x08 Sep 9 19:19:39 vinTux updating Energy Detect (ED) threshold: 112 Sep 9 19:19:39 vinTux updating Channel Clear Assessment (CCA) value: 0x0D Sep 9 19:19:39 vinTux updating channel to: 1 Sep 9 19:19:39 vinTux updating: enable Tx Sep 9 19:19:39 vinTux updating: enable Rx on channel: 1 Sep 9 19:19:39 vinTux updating short retry limit: 7, long retry limit: 4 Sep 9 19:19:39 vinTux updating tx MSDU lifetime: 4096 Sep 9 19:19:39 vinTux updating regulatory domain: 0x30 Sep 9 19:19:39 vinTux setting RXconfig to 2010:0FDD Sep 9 19:19:39 vinTux updating WEP key settings Sep 9 19:19:39 vinTux setting WEP key 0 as default Sep 9 19:19:39 vinTux acx_set_status(1):SCANNING Sep 9 19:19:39 vinTux starting radio scan Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x00000000 - after update Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x00000040 Sep 9 19:19:39 vinTux setting RXconfig to 2010:0FDD Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x00000000 - after update Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x00000040 Sep 9 19:19:39 vinTux setting RXconfig to 2010:0FDD Sep 9 19:19:39 vinTux get_mask 0x00000000, set_mask 0x00000000 - after update Sep 9 19:19:40 vinTux acx_i_timer: adev->status=1 (SCANNING) Sep 9 19:19:40 vinTux continuing scan (1 sec) Sep 9 19:19:40 vinTux no matching station found in range yet Sep 9 19:19:40 vinTux acx_set_status(1):SCANNING Sep 9 19:19:40 vinTux starting radio scan Sep 9 19:19:41 vinTux rc-scripts: no access points found Sep 9 19:19:41 vinTux rc-scripts: Couldn't find any access points on eth1 Sep 9 19:19:41 vinTux rc-scripts: Failed to configure wireless for eth1 Sep 9 19:19:41 vinTux get_mask 0x00000000, set_mask 0x00000250 Sep 9 19:19:41 vinTux updating transmit power: 0 dBm Sep 9 19:19:41 vinTux updating: disable Tx Sep 9 19:19:41 vinTux setting RXconfig to 2010:0FDD Sep 9 19:19:41 vinTux get_mask 0x00000000, set_mask 0x00000000 - after update Sep 9 19:19:41 vinTux acx_set_status(0):STOPPED Sep 9 19:19:41 vinTux closed device --- and the dmesg with acx module is: --- acx: this driver is still EXPERIMENTAL acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them running on a little-endian CPU PCI module v0.3.35 initialized, waiting for cards to probe... ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 acx: found ACX100-based wireless network card at 0000:02:00.0, irq:11, phymem1:0x42010000, phymem2:0x42000000, mem1:0xb8966000, mem1_size:4096, mem2:0xb8980000, mem2_size:65536 initial debug setting is 0x000A using IRQ 11 requesting firmware image 'tiacx100c0D' acx: firmware image 'tiacx100c0D' was not provided. Check your hotplug scripts requesting firmware image 'tiacx100' acx_write_fw (main/combined):0 acx_validate_fw (main/combined):0 requesting firmware image 'tiacx100r0D' acx_write_fw (radio): 0 acx_validate_fw (radio): 0 acx100_s_init_wep: writing WEP options initializing max packet templates NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536 CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01 AntennaID:00 Len:02 Data:01 02 PowerLevelID:01 Len:02 Data:001E 000A DataRatesID:02 Len:05 Data:02 04 11 22 44 DomainID:03 Len:06 Data:30 20 30 31 32 41 ProductID:04 Len:09 Data:TI ACX100 ManufacturerID:05 Len:07 Data:TI Test get_mask 0x00004D82, set_mask 0x00000000 got sensitivity value 176 got antenna value 0x8D got Energy Detect (ED) threshold 112 got Channel Clear Assessment (CCA) value 13 got regulatory domain 0x30 get_mask 0x00000000, set_mask 0x00000000 - after update new ratevector: 82 84 0B 16 2C setting RXconfig to 2010:0FDD acx: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x0D (Maxim), EEPROM version 0x05, uploaded firmware 'Rev 1.9.10.0_A4' (0x01030505) creating /proc entry driver/acx_wlan0 creating /proc entry driver/acx_wlan0_diag creating /proc entry driver/acx_wlan0_eeprom creating /proc entry driver/acx_wlan0_phy acx v0.3.35: net device wlan0, driver compiled against wireless extensions 20 USB module v0.3.35 initialized, probing for devices... usbcore: registered new driver acx_usb acx_set_status(1):SCANNING updating initial settings on iface activation get_mask 0x00000000, set_mask 0x0036EEFC important setting has been changed. Need to update packet templates, too updating packet templates updating Tx fallback to 1 retries updating transmit power: 18 dBm wlan0: changing radio power level to 18 dBm (23) updating antenna value: 0x8D updating Energy Detect (ED) threshold: 112 updating Channel Clear Assessment (CCA) value: 0x0D updating channel to: 1 updating: enable Tx updating: enable Rx on channel: 1 updating short retry limit: 7, long retry limit: 4 updating tx MSDU lifetime: 4096 updating regulatory domain: 0x30 setting RXconfig to 2010:0FDD updating WEP key settings setting WEP key 0 as default acx_set_status(1):SCANNING starting radio scan get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00000040 setting RXconfig to 2010:0FDD get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00000040 setting RXconfig to 2010:0FDD get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00000200 updating transmit power: 18 dBm wlan0: changing radio power level to 18 dBm (23) get_mask 0x00000000, set_mask 0x00000000 - after update new ratevector: 82 84 8B 96 2C get_mask 0x00000000, set_mask 0x00200004 updating packet templates updating Tx fallback to 1 retries get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00010000 important setting has been changed. Need to update packet templates, too updating packet templates acx_set_status(1):SCANNING start_scan: seems like previous scan is still running. Not starting anew. Please report get_mask 0x00000000, set_mask 0x00000000 - after update acx_i_timer: adev->status=1 (SCANNING) continuing scan (1 sec) start_scan: seems like previous scan is still running. Not starting anew. Please report no matching station found in range yet acx_set_status(1):SCANNING starting radio scan get_mask 0x00000000, set_mask 0x00000200 updating transmit power: 18 dBm wlan0: changing radio power level to 18 dBm (23) get_mask 0x00000000, set_mask 0x00000000 - after update new ratevector: 82 84 8B 96 2C get_mask 0x00000000, set_mask 0x00200004 updating packet templates updating Tx fallback to 1 retries get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00000210 updating transmit power: 0 dBm wlan0: changing radio power level to 0 dBm (63) updating: disable Tx get_mask 0x00000000, set_mask 0x00000000 - after update get_mask 0x00000000, set_mask 0x00000040 setting RXconfig to 2010:0FDD get_mask 0x00000000, set_mask 0x00000000 - after update acx_set_status(0):STOPPED closed device ---
Any idea? Sorry for my bad english and for this long mail! Regards VinX - To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
