Jesse Brandeburg [EMAIL PROTECTED] wrote:
| On 9/28/06, Sukadev Bhattiprolu <[EMAIL PROTECTED]> wrote:
| >Thanks. See below for additional info
| >
| >Auke Kok [EMAIL PROTECTED] wrote:
| >| Sukadev Bhattiprolu wrote:
| >| >
| >| >I am unable to get networking to work with 2.6.18-mm1 on my system.
| >| >
| >| >But 2.6.18 kernel on same system works fine. Here is some info about
| >| >the system/debug attempts. Attached are the lspci output and config.
| >| >
| >| >Appreciate any help. Please let me know if you need more info.
|
| It seems you're having interrupt delivery problems or interrupts are
| getting lost.
| rx_missed_errors indicates frames that were dropped due to the e1000
| adapter's fifo getting full and over flowing.
| >rx_no_buffer_count: 310
| >rx_missed_errors: 5865
| rx_no_buffer_count indicates that the driver didn't return buffers to
| the hardware soon enough, but the hardware was able to store the
| packet (at the time of reception) in the fifo to try again.
|
| Both these indicate to me that there is something wrong with
| interrupts. Maybe interrupt sharing
|
| can you possibly try a back to back connection with another linux box
| and run tcpdump on both ends then ping? it will tell us if traffic is
| truely getting out and coming in okay.
Unfortunately, I can't try this week, but can try it early next week.
|
| also please send output of lspci -vv and cat /proc/interrupts
lspci-vv.out is attached. Here is the /proc/interrupts:
$ cat /proc/interrupts
CPU0 CPU1
0: 18316 0 IO-APIC-edge timer
2: 0 0 XT-PIC-level cascade
4: 1023 0 IO-APIC-edge serial
8: 0 0 IO-APIC-edge rtc
17: 3380 0 IO-APIC-fasteoi libata
19: 174 0 IO-APIC-fasteoi ohci_hcd:usb1, ohci_hcd:usb2
28: 0 0 IO-APIC-fasteoi eth0
NMI: 96 35
LOC: 18251 18524
ERR: 0
$ lspci -vv
0000:00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e8100000-e81fffff
Prefetchable memory behind bridge: 88000000-880fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [c0] #08 [0086]
Capabilities: [f0] #08 [8000]
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
Subsystem: IBM: Unknown device 7468
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
(prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 7469
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1020 [size=16]
0000:00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
Subsystem: IBM: Unknown device 746a
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin D routed to IRQ 0
Region 0: I/O ports at 1000 [size=32]
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
Subsystem: IBM: Unknown device 746b
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
(rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] Capabilities: [b8] #08 [8000]
Capabilities: [c0] #08 [004a]
0000:00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
(prog-if 10 [IO-APIC])
Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at 88100000 (64-bit, non-prefetchable) [size=4K]
0000:00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
(rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8200000-e82fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [a0] Capabilities: [b8] #08 [8000]
0000:00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
(prog-if 10 [IO-APIC])
Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at 88101000 (64-bit, non-prefetchable) [size=4K]
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] #08 [2101]
Capabilities: [a0] #08 [2101]
Capabilities: [c0] #08 [2101]
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] #08 [2101]
Capabilities: [a0] #08 [2101]
Capabilities: [c0] #08 [2101]
0000:00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
0000:01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
(prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD] AMD-8111 USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 19
Region 0: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
0000:01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
(prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD] AMD-8111 USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 19
Region 0: Memory at e8101000 (32-bit, non-prefetchable) [size=4K]
0000:01:06.0 Mass storage controller: Silicon Image, Inc. SiI 3512
[SATALink/SATARaid] Serial ATA Controller (rev 01)
Subsystem: IBM: Unknown device 3512
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 2020 [size=8]
Region 1: I/O ports at 2014 [size=4]
Region 2: I/O ports at 2018 [size=8]
Region 3: I/O ports at 2010 [size=4]
Region 4: I/O ports at 2000 [size=16]
Region 5: Memory at e8102000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at 88000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:03:03.0 Ethernet controller: Intel Corporation 82544EI Gigabit Ethernet
Controller (Copper) (rev 02)
Subsystem: Intel Corporation PRO/1000 XT Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 28
Region 0: Memory at e8240000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e8220000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3400 [size=32]
Expansion ROM at e8260000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=2, DMOST=0, DMCRS=1, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
0000:03:04.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY
[Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 029a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at e8200000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at e8280000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
