On 17.08.2018 11:51, Harald Hoyer wrote: > On 16.08.2018 00:17, Siwei Liu wrote: >> On Wed, Aug 15, 2018 at 12:05 PM, Samudrala, Sridhar >> <sridhar.samudr...@intel.com> wrote: >>> On 8/14/2018 5:03 PM, Siwei Liu wrote: >>>> >>>> Are we sure all userspace apps skip and ignore slave interfaces by >>>> just looking at "IFLA_MASTER" attribute? >>>> >>>> When STANDBY is enabled on virtio-net, a failover master interface >>>> will appear, which automatically enslaves the virtio device. But it is >>>> found out that iSCSI (or any network boot) cannot boot strap over the >>>> new failover interface together with a standby virtio (without any VF >>>> or PT device in place). >>>> >>>> Dracut (initramfs) ends up with timeout and dropping into emergency shell: >>>> >>>> [ 228.170425] dracut-initqueue[377]: Warning: dracut-initqueue >>>> timeout - starting timeout scripts >>>> [ 228.171788] dracut-initqueue[377]: Warning: Could not boot. >>>> Starting Dracut Emergency Shell... >>>> Generating "/run/initramfs/rdsosreport.txt" >>>> Entering emergency mode. Exit the shell to continue. >>>> Type "journalctl" to view system logs. >>>> You might want to save "/run/initramfs/rdsosreport.txt" to a USB stick or >>>> /boot >>>> after mounting them and attach it to a bug report. >>>> dracut:/# ip l sh >>>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN >>>> mode DEFAULT group default qlen 1000 >>>> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 >>>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue >>>> state UP mode DEFAULT group default qlen 1000 >>>> link/ether 9a:46:22:ae:33:54 brd ff:ff:ff:ff:ff:ff\ >>>> 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast >>>> master eth0 state UP mode DEFAULT group default qlen 1000 >>>> link/ether 9a:46:22:ae:33:54 brd ff:ff:ff:ff:ff:ff >>>> dracut:/# >>>> >>>> If changing dracut code to ignore eth1 (with IFLA_MASTER attr), >>>> network boot starts to work. >>> >>> >>> Does dracut by default tries to use all the interfaces that are UP? >>> >> Yes. The specific dracut cmdline of our case is "ip=dhcp >> netroot=iscsi:... ", but it's not specific to iscsi boot. And because >> of same MAC address for failover and standby, while dracut tries to >> run DHCP on all interfaces that are up it eventually gets same route >> for each interface. Those conflict route entries kill off the network >> connection. >> >>> >>>> >>>> The reason is that dracut has its own means to differentiate virtual >>>> interfaces for network boot: it does not look at IFLA_MASTER and >>>> ignores slave interfaces. Instead, users have to provide explicit >>>> option e.g. bond=eth0,eth1 in the boot line, then dracut would know >>>> the config and ignore the slave interfaces. >>> >>> >>> Isn't it possible to specify the interface that should be used for network >>> boot? >> As I understand it, one can only specify interface name for running >> DHCP but not select interface for network boot. We want DHCP to run >> on every NIC that is up (excluding the enslaved interfaces), and only >> one of them can get a route entry to the network boot server (ie.g. >> iSCSI target). >> >>> >>> >>>> >>>> However, with automatic creation of failover interface that assumption >>>> is no longer true. Can we change dracut to ignore all slave interface >>>> by checking IFLA_MASTER? I don't think so. It has a large impact to >>>> existing configs. >>> >>> >>> What is the issue with checking for IFLA_MASTER? I guess this is used with >>> team/bonding setups. >> That should be discussed within and determined by the dracut >> community. But the current dracut code doesn't check IFLA_MASTER for >> team or bonding specifically. I guess this change might have broader >> impact to existing userspace that might be already relying on the >> current behaviour. >> >> Thanks, >> -Siwei > > Is there a sysfs flag for IFF_SLAVE? Or any "ip" output I can use to detect, > that it is a IFF_SLAVE? >
Oh, it's the other way around.. dracut should ignore "master" (eth1). Can the master enslave the "eth0", if it is already "UP" and busy later on?