On Thu, 25 Jun 2020 at 19:37, Russell King - ARM Linux admin <[email protected]> wrote: > > On Thu, Jun 25, 2020 at 06:23:28PM +0300, Vladimir Oltean wrote: > > From: Vladimir Oltean <[email protected]> > > > > state->speed holds a value of 10, 100, 1000 or 2500, but > > SYS_MAC_FC_CFG_FC_LINK_SPEED expects a value in the range 0, 1, 2 or 3. > > > > So set the correct speed encoding into this register. > > > > Signed-off-by: Vladimir Oltean <[email protected]> > > --- > > drivers/net/dsa/ocelot/felix.c | 27 +++++++++++++++++++++++---- > > 1 file changed, 23 insertions(+), 4 deletions(-) > > > > diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c > > index d229cb5d5f9e..da337c63e7ca 100644 > > --- a/drivers/net/dsa/ocelot/felix.c > > +++ b/drivers/net/dsa/ocelot/felix.c > > @@ -250,10 +250,25 @@ static void felix_phylink_mac_config(struct > > dsa_switch *ds, int port, > > DEV_CLOCK_CFG_LINK_SPEED(OCELOT_SPEED_1000), > > DEV_CLOCK_CFG); > > > > - /* Flow control. Link speed is only used here to evaluate the time > > - * specification in incoming pause frames. > > - */ > > - mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(state->speed); > > + switch (state->speed) { > > + case SPEED_10: > > + mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(3); > > + break; > > + case SPEED_100: > > + mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(2); > > + break; > > + case SPEED_1000: > > + case SPEED_2500: > > + mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(1); > > + break; > > + case SPEED_UNKNOWN: > > + mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(0); > > + break; > > + default: > > + dev_err(ocelot->dev, "Unsupported speed on port %d: %d\n", > > + port, state->speed); > > + return; > > + } > > > > /* handle Rx pause in all cases, with 2500base-X this is used for rate > > * adaptation. > > @@ -265,6 +280,10 @@ static void felix_phylink_mac_config(struct dsa_switch > > *ds, int port, > > SYS_MAC_FC_CFG_PAUSE_VAL_CFG(0xffff) | > > SYS_MAC_FC_CFG_FC_LATENCY_CFG(0x7) | > > SYS_MAC_FC_CFG_ZERO_PAUSE_ENA; > > + > > + /* Flow control. Link speed is only used here to evaluate the time > > + * specification in incoming pause frames. > > + */ > > ocelot_write_rix(ocelot, mac_fc_cfg, SYS_MAC_FC_CFG, port); > > I'm not that happy with the persistence of felix using the legacy > method; I can bring a horse to water but can't make it drink comes > to mind. I'm at the point where I don't care _if_ my phylink changes > break code that I've asked people to convert and they haven't yet, > and I'm planning to send the series that /may/ cause breakage in > that regard pretty soon, so the lynx PCS changes can move forward. > > I even tried to move felix forward by sending a patch for it, and I > just gave up with that approach based on your comment. > > Shrug. > > -- > RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ > FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
The callbacks clearly work the way they are, given the current structure of phylink, as proven by the users of this driver. Code that isn't there yet simply isn't there yet. What you consider "useless churn" and what I consider "useless churn" are pretty different things. To me, patch 7/7 is the useless churn, that's why it's at the end. Patches 1-6 are structured in a way that is compatible with backporting to a stable 5.4 tree. Patch 7, not so much. The fact that you have such an attitude and you make the effort to actually send an email complaining about me using state->speed in .mac_config(), when literally 3 patches later I'm moving this configuration where you want it to be, is pretty annoying.
