On 9/11/2020 11:56 PM, Nikolay Aleksandrov wrote:
On Sat, 2020-09-12 at 02:16 +0300, Vladimir Oltean wrote:
Currently the bridge untags VLANs from its VLAN group in
__allowed_ingress() only when VLAN filtering is enabled.
When installing a pvid in egress-tagged mode, DSA switches have a
problem:
ip link add dev br0 type bridge vlan_filtering 0
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid
When adding a VLAN on a DSA switch interface, DSA configures the VLAN
membership of the CPU port using the same flags as swp0 (in this case
"pvid and not untagged"), in an attempt to copy the frame as-is from
ingress to the CPU.
However, in this case, the packet may arrive untagged on ingress, it
will be pvid-tagged by the ingress port, and will be sent as
egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN
tag where there was none to speak of on ingress.
When vlan_filtering is 1, this is not a problem, as stated in the first
paragraph, because __allowed_ingress() will pop it. But currently, when
vlan_filtering is 0 and we have such a VLAN configuration, we need an
8021q upper (br0.1) to be able to ping over that VLAN.
Make the 2 cases (vlan_filtering 0 and 1) behave the same way by popping
the pvid, if the skb happens to be tagged with it, when vlan_filtering
is 0.
There was an attempt to resolve this issue locally within the DSA
receive data path, but even though we can determine that we are under a
bridge with vlan_filtering=0, there are still some challenges:
- we cannot be certain that the skb will end up in the software bridge's
data path, and for that reason, we may be popping the VLAN for
nothing. Example: there might exist an 8021q upper with the same VLAN,
or this interface might be a DSA master for another switch. In that
case, the VLAN should definitely not be popped even if it is equal to
the default_pvid of the bridge, because it will be consumed about the
DSA layer below.
Could you point me to a thread where these problems were discussed and why
they couldn't be resolved within DSA in detail ?
- the bridge API only offers a race-free API for determining the pvid of
a port, br_vlan_get_pvid(), under RTNL.
The API can be easily extended.
And in fact this might not even be a situation unique to DSA. Any driver
that receives untagged frames as pvid-tagged is now able to communicate
without needing an 8021q upper for the pvid.
I would prefer we don't add hardware/driver-specific fixes in the bridge, when
vlan filtering is disabled there should be no vlan manipulation/filtering done
by the bridge. This could potentially break users who have added 8021q devices
as bridge ports. At the very least this needs to be hidden behind a new option,
but I would like to find a way to actually push it back to DSA. But again adding
hardware/driver-specific options should be avoided.
Can you use tc to pop the vlan on ingress ? I mean the cases above are visible
to the user, so they might decide to add the ingress vlan rule.
We had discussed various options with Vladimir in the threads he points
out but this one is by far the cleanest and basically aligns the data
path when the bridge is configured with vlan_filtering=0 or 1.
Some Ethernet switches supported via DSA either insist on or the driver
has been written in such a way that the default_pvid of the bridge which
is egress untagged for the user-facing ports is configured as egress
tagged for the CPU port. That CPU port is ultimately responsible for
bringing the Ethernet frames into the Linux host and the bridge data
path which is how we got VLAN tagged frames into the bridge, even if a
vlan_filtering=0 bridge is not supposed to.
We can solve this today by having a 802.1Q upper on top of the bridge
default to pop/push the default_pvid VLAN tag, but this is not obvious,
represents a divergence from a pure software bridge, and leads to
support questions. What is also utterly confusing for instance is that a
raw socket like one opened by a DHCP client will successfully allow br0
to obtain an IP address, but the data path still is not functional, as
you would need to use br0.1 to have a working data path taking care of
the VLAN tag.
Vladimir had offered a DSA centric solution to this problem, which was
not that bad after all, but this one is also my favorite.
Let us know when you are caught up on the thread and we can see how to
solve that the best way.
--
Florian
