Hi!

> From: Rafael J. Wysocki <[EMAIL PROTECTED]>
> 
> Add suspend/resume support to the uli526x network driver (tested on x86_64,
> with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 
> 40').
> 
> Signed-off-by: Rafael J. Wysocki <[EMAIL PROTECTED]>

Looks ok to me.

> +#ifdef CONFIG_PM
> +
> +/*
> + *   Suspend the interface.
> + */
> +
> +static int uli526x_suspend(struct pci_dev *pdev, pm_message_t state)
> +{
> +     struct net_device *dev = pci_get_drvdata(pdev);
> +
> +     ULI526X_DBUG(0, "uli526x_suspend", 0);
> +
> +     if (dev && netdev_priv(dev)) {
> +             if (netif_running(dev)) {
> +                     netif_device_detach(dev);
> +                     uli526x_down(dev);
> +             }
> +             pci_save_state(pdev);
> +             pci_enable_wake(pdev, pci_choose_state(pdev, state), 0);
> +             pci_disable_device(pdev);
> +             pci_set_power_state(pdev, pci_choose_state(pdev, state));
> +     }
> +     return 0;
> +}
> +
> +/*
> + *   Resume the interface.
> + */
> +
> +static int uli526x_resume(struct pci_dev *pdev)
> +{
> +     struct net_device *dev = pci_get_drvdata(pdev);
> +     struct uli526x_board_info *db = netdev_priv(dev);
> +     int err;
> +
> +     ULI526X_DBUG(0, "uli526x_resume", 0);
> +
> +     if (dev && db) {
> +             pci_set_power_state(pdev, PCI_D0);
> +             err = pci_enable_device(pdev);
> +             if (err) {
> +                     printk(KERN_WARNING "%s: Could not enable device \n",
> +                             dev->name);
> +                     return err;
> +             }
> +             pci_restore_state(pdev);
> +             pci_set_master(pdev);
> +             if (netif_running(dev)) {
> +                     uli526x_up(dev);
> +                     netif_device_attach(dev);
> +             }
> +     }
> +     return 0;
> +}
> +
#else 
#define *_resume NULL
#define *_suspend NULL

> +#endif /* CONFIG_PM */

> @@ -1689,6 +1775,10 @@ static struct pci_driver uli526x_driver 
>       .id_table       = uli526x_pci_tbl,
>       .probe          = uli526x_init_one,
>       .remove         = __devexit_p(uli526x_remove_one),
> +#ifdef CONFIG_PM
> +     .suspend        = uli526x_suspend,
> +     .resume         = uli526x_resume,
> +#endif

...so that this ifdef is not needed?
                                                                Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) 
http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to