Hi,
Toshiba R600, snv_127
From time to time nwam can't configure iwh0 interface. If i restart
nwam then usually it helps and it works fine. But sometimes it doesn't
help and I have to reboot OS to recover.
When it helps I can see in logs:
Dec 1 11:50:12 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
Dec 1 11:50:12 r600 iwh: [ID 808906 kern.warning] WARNING:
iwh_init(): failed to configure device
Dec 1 11:50:26 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
Dec 1 11:50:26 r600 iwh: [ID 808906 kern.warning] WARNING:
iwh_init(): failed to configure device
Dec 1 11:51:08 r600 mac: [ID 744254 kern.info] NOTICE: iwh0 link up
Then I suspended the system and now I can't get nwam to configure iwh
interface.
Dec 1 12:28:25 r600 acpica: [ID 530733 kern.notice] NOTICE:
acpica_ddi_setwake: could not evaluate _PRW
Dec 1 12:42:03 r600 last message repeated 2 times
Dec 1 12:42:03 r600 pciehpc: [ID 786987 kern.notice] NOTICE: Unknown
Notify() event 1 on slot #1
Dec 1 12:42:05 r600 acpica: [ID 530733 kern.notice] NOTICE:
acpica_ddi_setwake: could not evaluate _PRW
Dec 1 12:42:10 r600 unix: [ID 954099 kern.info] NOTICE: IRQ16 is
being shared by drivers with different interrupt levels.
Dec 1 12:42:10 r600 This may result in reduced system performance.
Dec 1 12:42:11 r600 /sbin/dhcpagent[326]: [ID 967406 daemon.warning]
refreshing state on iwh0
Dec 1 12:42:11 r600 syseventd[12634]: [ID 555171 daemon.error]
Fatal:attempting to dump core
Dec 1 12:42:12 r600 genunix: [ID 583038 kern.notice] System has been
resumed.
Dec 1 12:42:12 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
Dec 1 12:42:12 r600 iwh: [ID 808906 kern.warning] WARNING:
iwh_init(): failed to configure device
Dec 1 12:42:15 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
Dec 1 12:42:15 r600 iwh: [ID 808906 kern.warning] WARNING:
iwh_init(): failed to configure device
Dec 1 12:42:17 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
Dec 1 12:42:17 r600 iwh: [ID 808906 kern.warning] WARNING:
iwh_init(): failed to configure device
Dec 1 12:42:19 r600 iwh: [ID 450215 kern.warning] WARNING:
iwh_config(): failed to set power mode
After I reboot it then it works fine... until next time it happens.
I'm not 100% sure but I believe that it also happens sometimes even
without going thry suspend/resume cycle.
At least it did on older builds.
--
Robert Milkowski
http://milek.blogspot.com
_______________________________________________
networking-discuss mailing list
[email protected]
