I found some .debs to install network manager 0.7.0 from CVS in the ubuntu forums. They were dated 10/10/2006. I tried using the program to connect to the wireless network here at school, but no dice. I followed another users suggestion and made a symlink libdbus-1.so.2 to libdbus-1.so.3 and made sure that wpa_supplicant was either in /sbin or linked to from /sbin (it was in /sbin). I then ran:
sudo NetworkManager --no-daemon in one terminal and: nm-applet in another. I got the following output from the first command: [EMAIL PROTECTED]:~$ sudo NetworkManager --no-daemon Password: NetworkManager: <info> starting... NetworkManager: <info> New VPN service 'vpnc' ( org.freedesktop.NetworkManager.vpnc). NetworkManager: <info> ath0: Device is fully-supported using driver 'ath_pci'. NetworkManager: <info> nm_device_init(): waiting for device's worker thread to start NetworkManager: <info> nm_device_init(): device's worker thread started, continuing. NetworkManager: <info> Now managing wireless (802.11) device 'ath0'. NetworkManager: <info> Deactivating device ath0. NetworkManager: <info> eth0: Device is fully-supported using driver 'e100'. NetworkManager: <info> nm_device_init(): waiting for device's worker thread to start NetworkManager: <info> nm_device_init(): device's worker thread started, continuing. NetworkManager: <info> Now managing wired Ethernet (802.3) device 'eth0'. NetworkManager: <info> Deactivating device eth0. NetworkManager: <info> Updating allowed wireless network lists. NetworkManager: <debug> [1172696570.353095] nm_device_802_11_wireless_get_activation_ap(): Forcing AP 'tsunami' NetworkManager: <info> User Switch: /org/freedesktop/NetworkManager/Devices/ath0 / tsunami NetworkManager: <info> Deactivating device ath0. NetworkManager: <info> Device ath0 activation scheduled... NetworkManager: <info> Activation (ath0) started... NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) scheduled... NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) started... NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) scheduled... NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) complete. NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) starting... NetworkManager: <info> Activation (ath0/wireless): access point 'tsunami' is encrypted, but NO valid key exists. New key needed. NetworkManager: <info> Activation (ath0) New wireless user key requested for network 'tsunami'. NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) complete. NetworkManager: <info> Activation (ath0) New wireless user key for network 'tsunami' received. NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) scheduled... NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) started... NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) scheduled... NetworkManager: <info> Activation (ath0) Stage 1 of 5 (Device Prepare) complete. NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) starting... NetworkManager: <info> Activation (ath0/wireless): access point 'tsunami' is encrypted, and a key exists. No new key needed. NetworkManager: <info> SUP: sending command 'INTERFACE_ADD ath0 wext /var/run/wpa_supplicant ' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'AP_SCAN 1' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'ADD_NETWORK' NetworkManager: <info> SUP: response was '0' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 ssid 7473756e616d69' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 proto WPA' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 key_mgmt IEEE8021X' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 eap LEAP' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 identity "mds50"' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 password <password>' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> SUP: sending command 'ENABLE_NETWORK 0' NetworkManager: <info> SUP: response was 'OK' NetworkManager: <info> Activation (ath0) Stage 2 of 5 (Device Configure) complete. NetworkManager: <info> Old device 'ath0' activating, won't change. NetworkManager: <info> Activation (ath0/wireless): association took too long (>120s), failing activation. NetworkManager: <info> Activation (ath0) failure scheduled... NetworkManager: <info> Activation (ath0) failed for access point (tsunami) NetworkManager: <info> Activation (ath0) failed. NetworkManager: <info> Deactivating device ath0. sendmsg(CTRL_IFACE monitor): No such file or directory I have no idea what this means, but it looks like it should be working??? I have been told that the network is standard cisco LEAP here at the University of Akron, but then again I haven't tried to talk to the top guy in charge of the network. The school is currently having a problem with people buying laptops with Vista as Vista will not do LEAP either, so maybe we can convince them to use some other solution. What should I suggest to them that would provide good security and be easy to set up for many users? Oh, I am using a Proxim Orinoco Gold 11a/b/g ComboCard with the Atheros Chipset under Madwifi. Should I try ndiswrapper or is there some other card I can get that will work natively?
_______________________________________________ NetworkManager-list mailing list NetworkManager-list@gnome.org http://mail.gnome.org/mailman/listinfo/networkmanager-list