Hi,
Can anyone help? I have been struggling with this problem for ages, RTFM etc. hasn't resolved it for me.
MDK9.1. Using cdrecord on the CLI. My Sony CD-writer writes happily to a Toshiba CD-RW, multi-session ,etc. no problem; but I cannot write anything to a CD-R (I've tried Sony Supremas, Kodak Ultima 80, Packard Bell 1-32x).
The messages I get are all minor variations on the following, and the commands minor variations on "cdrecord -v speed=2 dev=0,0,0 -data image-name" (burnfree ON,OFF; multi, no multi,etc)
What the h**l is going on?
DougB
Cdrecord 2.0 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.24 Using libscg version 'schily-0.7' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'SONY ' Identifikation : 'CD-RW CRX175E2 ' Revision : 'S002' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : MMC-2 SWABAUDIO BURNFREE FORCESPEED Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R Drive buf size : 1359872 = 1328 KB FIFO size : 4194304 = 4096 KB Track 01: data 0 MB padsize: 312 KB Total size: 0 MB (00:04.02) = 302 sectors Lout start: 1 MB (00:06/02) = 302 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 4 Is not unrestricted Is not erasable Disk sub type: Medium Type A, low Beta category (A-) (2) ATIP start of lead in: -12508 (97:15/17) ATIP start of lead out: 359848 (79:59/73) Disk type: Short strategy type (Phthalocyanine or similar) Manuf. index: 22 Manufacturer: Ritek Co. Blocks total: 359848 Blocks current: 359848 Blocks remaining: 359546 Forcespeed is OFF. Starting to write CD/DVD at speed 4 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Performing OPC... cdrecord: Input/output error. send opc: scsi sendcmd: no error CDB: 54 01 00 00 00 00 00 00 00 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 03 00 00 00 00 0C 00 00 00 00 73 03 00 00 Sense Key: 0x3 Medium Error, Segment 0 Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 3.693s timeout 60s cdrecord: OPC failed. Writing time: 3.711s cdrecord: fifo had 5 puts and 0 gets. cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
"cdrecord: OPC failed" I believe it is saying that the drive has failed. That could mean anything. Maybe the drive isn't set up right for cdrecord to work with it. or maybe the driver doesn't work with your make and model.
First thing I would do is in a terminal,
[EMAIL PROTECTED] root]# cdrecord -scanbus, Cdrecord 2.0 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
scsibus0:
0,0,0 0) 'Generic ' 'USB Storage-SMC ' '0090' Removable Disk
scsibus1:
1,0,0 100) 'PIONEER ' 'DVD-ROM DVD-116 ' '1.22' Removable CD-ROM
1,1,0 101) 'MITSUMI ' 'CR-48X9TE ' '1.0C' Removable CD-ROM
To see what you have got in the way of recognised devices.
John
--
John Richard Smith
[EMAIL PROTECTED]
Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com
