That would be "insmod 3c59x <ENTER>" and that will do it just "ifup
eth0<ENTER> and it will work.
Sean
shuxclams wrote:
>
> the module for a 905b is 3c59x, give that awhirl. ;)
>
> Sean
>
> Dave wrote:
> >
> > ...but insmod of course doesn't work when I use 3c90x (3c905 and 3c905b
> > don't exist...)
> > -dave
> >
> > -----Original Message-----
> > From: Jaguar [mailto:[EMAIL PROTECTED]]
> > Sent: Thursday, February 03, 2000 10:11 AM
> > To: [EMAIL PROTECTED]
> > Subject: Re: [RE: [newbie] DHCP...]
> >
> > There seems to be confusion about the chipset.
> > Since there is both a 3C509, and a 3C905...I suggest pulling the card after
> > POWER OFF....and reading the chipset off of the card...to make sure you are
> > trying the correct Driver.
> > HTH
> > Jaguar
> >
> > "Dave" <[EMAIL PROTECTED]> wrote:
> > > yep...I know it's a 3c905B card...
> > > and I looked through the documentation again and didn't see anything of
> > > help. One thing I'm confused about,however: if it is the IRQ etc., how do
> > i
> > > change that? (I have win98 too)
> > > Thanks
> > > Dave
> > >
> > > -----Original Message-----
> > > From: flupke [mailto:[EMAIL PROTECTED]]
> > > Sent: Thursday, February 03, 2000 5:07 AM
> > > To: [EMAIL PROTECTED]
> > > Subject: RE: [newbie] DHCP...
> > >
> > >
> > > there is a task manager called ktop. It seems that it's what you need.
> > > About your 3com card : are you sure this is the module you need?
> > > Is there anything mentionned about that in your card's documentation?
> > >
> > > Dave wrote :
> > > > insmod 3c509 gives me
> > > > ./3c509.o: init_module: Device or resource busy
> > > > ....sorry to have so little to go on, but I have no way of figuring out
> > > what
> > > > tto do next.
> > > > (on a side note, is there a taskmanager or ctrl+alt+del equivalent in
> > > linux?
> > > > I know that there is ps, but anything else (especially if it is
> > accesible
> > > in
> > > > KDE))?
> > > > Thanks
> > > > Dave
> > > >
> > > > >>>>>>>>>
> > > > have you tried a insmod 3c509 ??
> > > > does not look like the mod for the nic is loaded (hence the no eth0 in
> > > > ifconfig)
> > > > after you try the insmod (and get no errors ) try a modprobe 3c509
> > > > and then a ifconfig if you then see a eth0 ... BINGO
> > > > you can go into linuxconf and edit eth0 to use the 3c509 modual and dhcp
> > > > protocol.
> > > > after you save and exit linuxconf try ifconfig again you should see
> > eth0,
> > > > if no do a ifup eth0
> > > >
> > > > Regards,
> > > > ROn
> >
> > ____________________________________________________________________
> > Get your own FREE, personal Netscape WebMail account today at
> > http://webmail.netscape.com.
>
> __________________________________________________
> Do You Yahoo!?
> Talk to your friends online with Yahoo! Messenger.
> http://im.yahoo.com
__________________________________________________
Do You Yahoo!?
Talk to your friends online with Yahoo! Messenger.
http://im.yahoo.com
