petzhouse private wrote:
>
> Can I figure out something from this no. But I DO know a way to just restart
> everything. After several temper tantrums and mentals breakdowns do the
> following:
>
> 1. Insert the linux mandrake cd-rom (or installation media if it is not a
> cd-rom)
>
> 2. Boot the computer with it
>
> 3. Go through the installation process normally
>
> 4. Reinstall Linux Mandrake
>
> I have used this techneque repetitivly (it works well.)
>
> >From: Jacqueline Michell <[EMAIL PROTECTED]>
> >Reply-To: [EMAIL PROTECTED]
> >To: newbie list <[EMAIL PROTECTED]>
> >Subject: [newbie] sndconfig
> >Date: Sun, 18 Feb 2001 15:32:23 -0600
> >
> >After finally running sndconfig, I have sound and CD's play music, but. .
> >. Because of new boot messages that have started to show up, I'm wondering
> >if I have the wrong soundcard configured (it should be Creative SB16) or
> >what. So far, if sndconfig provides a way to scrap everything and start
> >over I haven't found it. I'll be very grateful if some kind soul could
> >look over the info given below and give help and suggestions?
> >
> >Jacqueline Michell
> >------------------------------------------------------------------
> >
> >from relevant lines of: /var/log/messages:
> >-------
> >isapnp: Card 'Creative EMU8000 PnP (soundcard?)
> >isapnp: Card 'Creative VIBRA16C PnP (soundcard?)
> >isapnp: 2 Plug & Play cards detected total
> >isapnp: card 'CTL0070' order 1 not found (soundcard--SB16??)
> >-------
> >later kernal boot messages:
> >isapnp: Board 1 has identity 1f 00 0e 7d c0 a3 00 8c 0e: CTL00a3 Serial
> >No 949696 (checksum 1f)
> >isapnp: Board 2 has identity e5 ff ff ff ff 70 00 8c 0e: CTL0070
> >Serial No -1 (checksum e5)
> >
> >After this CTL00a3 (the wavetable) is enabled OK at I/O port 620 (just as
> >in Windows)
> >CTL0070/-1[0]is enabled OK (with same values as in Windows) and
> >CTL0070/-1[1] is enabled for games
> >(there is nothing here about 'Creative VIBRA16' but it so identified in the
> >file: /etc/isapnp.conf)
> >-------
> >even later boot messages:
> >modprobe: /lib/modules/2.2.17-21mdk/misc/sb.o:
> >modprobe: Hint: insmod errors can be caused by incorrect module parameters,
> >including invalid IO or IRQ parameters
> >modprobe: init_module: Device or resource busy
> >modprobe: /lib/modules/2.2.17-21mdk/misc/sb.o: insmod
> >/lib/modules/2.2.17-21mdk/misc/sb.o failed
> >modprobe: /lib/modules/2.2.17-21mdk/misc/sb.o: insmod sb failed
> >sound: Loading sound module (sb) failed
> >modprobe: /lib/modules/2.2.17-21mdk/misc/op13.o:
> >modprobe: Hint: insmod errors can be caused by incorrect module parameters,
> >including invalid IO or IRQ parameters
> >modprobe: init_module: Device or resource busy
> >modprobe: /lib/modules/2.2.17-21mdk/misc/op13.o: insmod
> >/lib/modules/2.2.17-21mdk/misc/op13.o failed
> >modprobe: /lib/modules/2.2.17-21mdk/misc/op13.o: insmod op13 failed
> >sound: Loading midi module (op13) failed
> >
It appears that you need to recompile your modules. As thta is why you
can not get it to work.
--
.--. `
|__| .-------. Altoine Barker
|=.| |.-----.| Maximum Time, Inc
|--| ||$SEND|| Chicago Based Enterprise
| | |'-----'| http://www.maximumtime.com
|__|~')_____('