You ask a great question but it needs parameters to qualify it. You say lost? 
By that do you mean it was better at some time before ? The 650 has a quite 
distinct burst at 4500RPM when it comes into the sweet spot for it's tuning. If 
you have ridden others that worked better then we have a case to work on. They 
have a single accelerator pump that feeds all carbs via a passage way. Even so, 
the pump only provides a short squirt of fuel when opening the throttle. With 
them off and the bowls filled, operate the throttle linkage and observe the 
discharge from the intake valve side. There was a wonderful book on carb basics 
by the Mikuni people, I haven't seen one in years. Mine was stolen by a 
customer. The book had a great explanation of the sequence of jet systems. 
Idle, several stages of slight throttle opening, slow jet, and the transition 
to the main. The slides are controlled by vacuum and also meter fuel via the 
jet needle / needle jet combination.The
 needle jet is also the emulsification tube. Blockage at ANY point causes 
problems. I try to never remove the diaphragm capsĀ  and disassemble them. 
Because of the age of these bikes and the high cost replacements, they are 
better left alone. I test them by lifting them with a finger and releasing 
them. With four to test, any one that does not feel "right" may be torn or 
otherwise defective. (Right=a breathing noise, and some resistance to lifting 
with a controlled return) Yes, they are critical to mid-range performance. 
However, a failed one would not allow acceptable high speed performance. I 
dismiss the ignition as a problem because in all my years I have not seen a 
failure mode that was RPM related. Yours idles smoothly and goes good at high 
RPM. 
Now, lets take a different approach Are you sure the replacement slow jets are 
the right size ? I've sweated my way through many customer carb problems only 
to find that somebody had already re-jetted the bike. After that, I always 
check the jets with a wire gauge set to ensure they haven't been drilled out. 
An over-rich condition exhibits almost the same as a too lean one. Plug checks 
become vital. Try to induce the problem RPM range for as long as you can (IE: 
up a grade at a fixed throttle position) shut the motor off, pull the clutch 
and coast to a stop. If you could hold it that way long enough, the plugs will 
show what the condition is. An over-rich condition looks like a lean one since 
the intake tract air speed is too slow to carry in the excess fuel. Lets say 
the plugs look as though a lean condition exists. Repeat the ride and slowly 
add choke to it. Gets worse ? Gets better ? The choke is an enrichener and is 
adding fuel as opposed to a choke
 butterfly that would restrict air. Now they both sound as though they would do 
the same thing but that isn't so. The butterfly is actually causing an increase 
in air speed as it's closed. At a certain point, the increased air speed may 
make things work fine. 
Sorry, no easy answers. Have you examined the rubber spigots that hold the 
carbs ? They are known to crack and let in air. With the motor running, spray 
them with carb cleaner and note if engine speed increases. 
After all this boring BS, try for a detailed description of throttle opening / 
road speed / engine speed. 

--- On Mon, 11/24/08, Graham Kraker <[EMAIL PROTECTED]> wrote:
From: Graham Kraker <[EMAIL PROTECTED]>
Subject: [Nighthawk Lovers] What happened to my middle???
To: "Nighthawk Motorcycle Lovers!" <[email protected]>
Date: Monday, November 24, 2008, 4:01 AM

I've tried about everything I know of to repair this loss of midrange
power as my bike revs up with no luck.  Such as:  plugs, wires, carb
removal/disassemble/clean/inspect/install, air filter, petcock rebuild
and countless hours with no sucsess.  It idles way better now and has
more top end than ever, but it still feels like cylinders 1-2, or 2-3
die during acceleration unless I keep the rpms over 4500.  I learned
that the slow jet may play a role in this and no change except the
smoother idle after replacing them.  I heard somewhere else about an
accelerator pump, but can't locate/identify it.  Since the carbs main
aperature is vacuum controlled possiblly I have insufficient vacuum
under 4500rps, but why the vacuum seems cool at idle and high?

Open to speculation and educated guesses

Thanks Graham M.




      
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to [EMAIL PROTECTED]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to