On Thu, Jul 3, 2014 at 11:09 PM, Yijing Wang <wangyij...@huawei.com> wrote: > On 2014/7/4 10:43, Ilia Mirkin wrote: >> On Thu, Jul 3, 2014 at 10:35 PM, Yijing Wang <wangyij...@huawei.com> wrote: >>> Hi Brian, >>> From your 01:00.0 VGA compatible controller PCI config register, it >>> supports 1 MSI vector, so I think this >>> card has no problem. But you didn't answer what's the pci_enable_msi() >>> return during it enable MSI fail. >>> >>> You can check PCI bus whether support MSI like: >>> >>> cat /sys/bus/pci/devices/00:0e.0/msi_bus >>> >>> Other, do you call pci_enable_device() before pci_enable_msi() ? >> >> Yes, the device is enabled. nouveau does generally work for most >> people :) And it works fine here if MSI is forced off. >> >> The problem here is that pci_enable_msi() succeeds, but it probably > > It's some strange, pci_enable_msi() succeeds, but there is nothing in MSI > address and data register > > Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Because the address and data is invalid, so MSI can not work. > > Because you said pci_enable_msi() return 0 which indicates success, so I > guess the device > current power state is not D0, because checking code in __write_msi_msi. > > void __write_msi_msg(struct msi_desc *entry, struct msi_msg *msg) > { > if (entry->dev->current_state != PCI_D0) { > /* Don't touch the hardware now */ > } else if (entry->msi_attrib.is_msix) { > void __iomem *base; > base = entry->mask_base + > entry->msi_attrib.entry_nr * PCI_MSIX_ENTRY_SIZE; > > writel(msg->address_lo, base + PCI_MSIX_ENTRY_LOWER_ADDR); > writel(msg->address_hi, base + PCI_MSIX_ENTRY_UPPER_ADDR); > writel(msg->data, base + PCI_MSIX_ENTRY_DATA); > ...... > >> shouldn't. I don't know all the details about MSI, but doesn't the CPU >> or (L)APIC have to support it? In this case, it's a P200MMX on a 430FX >> chipset board. Both quite ancient... > > MSI in x86 always send to specific interrupt address(0xfeexxxx), most x86 CPU > should support MSI, but I am not sure, I don't know hardware much.
To put things in perspective, P200MMX was released in early 1997. It looks like the PCI 2.2 spec, which defines MSI, was released in late 1998. The 430FX chipset only supports PCI 2.0. > >> >> So given that the PCI device itself supports MSI, how do we tell that >> it shouldn't actually get turned on? > > Generally, some message in dmesg like: > [ 17.322311] ahci 0000:00:1f.2: irq 119 for MSI/MSI-X > [ 17.322319] ahci 0000:00:1f.2: irq 120 for MSI/MSI-X > [ 17.322326] ahci 0000:00:1f.2: irq 121 for MSI/MSI-X > [ 17.322333] ahci 0000:00:1f.2: irq 122 for MSI/MSI-X > [ 17.322339] ahci 0000:00:1f.2: irq 123 for MSI/MSI-X > > Also you can check /proc/interrupts I think. I must not have made my question clear. Let me try again: There is a NVIDIA G96 GPU (which is PCIe only) hanging off of a PCIe <-> PCI bridge (all on one card), which is plugged into a motherboard with the 430FX chipset (PCI 2.0 supported). The GPU PCI device, of course, has full support for MSI. However my understanding is that MSI won't actually work here. This is confirmed by the fact that if we let nouveau enable MSI, the device doesn't work (presumably due to lack of interrupt delivery, although I admit to not having debugged it that far). How do I, as a nouveau driver developer, know not to call pci_enable_msi? Or alternatively how can pci_enable_msi be taught not to succeed in this case? Thanks, -ilia _______________________________________________ Nouveau mailing list Nouveau@lists.freedesktop.org http://lists.freedesktop.org/mailman/listinfo/nouveau