Stephen, this is not the behaviour I expect. Can you please add “-b 1” and show me some logs after nprobe stops sending data out?
thanks luca > On 09 Mar 2015, at 13:55, Stephen Stocke <[email protected]> wrote: > > Hi Luca > > Yes, it seems like it is happy with the license as below. However, I started > out using a trial version and added the license later, i.e. the nprobe.exe is > the one from the trial installation. Could that be relevant? > > Thanks for the prompt reply. > > Kind regards > Steve > > C:\Program Files\nProbe>nprobe /c > Running nProbe for Win32. > About to start nProbe > nProbe started > 09/Mar/2015 12:51:20 [nprobe.c:6144] Valid nProbe license found > 09/Mar/2015 12:51:20 [nprobe.c:4197] WARNING: The output interfaceId is set > to 0: did you forget to > use -Q perhaps ? > 09/Mar/2015 12:51:20 [nprobe.c:4200] WARNING: The input interfaceId is set to > 0: did you forget to u > se -u perhaps ? > 09/Mar/2015 12:51:20 [nprobe.c:4255] Welcome to nprobe v.7.1.150107 > ($Revision: 4384 $) for Windows > > 09/Mar/2015 12:51:20 [nprobe.c:4273] nProbe SystemId: 362669240-b205a206 > 09/Mar/2015 12:51:20 [nprobe.c:4285] nProbe License: > 4040F6C8C6E284C6F2B10A4A449DB7451455036041BA4D > 16D8 > 09/Mar/2015 12:51:20 [nprobe.c:4326] WARNING: -n parameter is missing. > 127.0.0.1:2055 <http://127.0.0.1:2055/> will be used. > 09/Mar/2015 12:51:20 [nprobe.c:6179] Welcome to nprobe v.7.1.150107 for > Windows > 09/Mar/2015 12:51:20 [plugin.c:990] 0 plugin(s) enabled > 09/Mar/2015 12:51:20 [nprobe.c:4783] Using packet capture length 128 > 09/Mar/2015 12:51:20 [nprobe.c:6347] IPv6 traffic will NOT be > exported/accounted by this probe > 09/Mar/2015 12:51:20 [nprobe.c:6348] due to configuration options (e.g. use > NetFlow v9) > 09/Mar/2015 12:51:20 [nprobe.c:6393] Flows ASs will not be computed (missing > GeoIP support) > 09/Mar/2015 12:51:20 [nprobe.c:6478] Capturing packets from interface > \Device\NPF_{9754458C-9D75-4E5 > 3-AC60-D52FE2EA3FD8} [snaplen: 128 bytes] > 09/Mar/2015 12:51:20 [nprobe.c:6684] nProbe started successfully > > > On 9 March 2015 at 12:21, Luca Deri <[email protected] <mailto:[email protected]>> > wrote: > Steve > is the license installed? Please start it from shell and do nprobe.exe /c to > see if it complains > > Regards Luca > > > On 03/09/2015 12:56 PM, Stephen Stocke wrote: >> Hi All >> >> I'm running nProbe v.7.1.150107 Rev.4384 on a Windows 2008R2 server to >> collect flows from a pair of switch mirror ports. >> >> If I run nProbe in an interactive command prompt it works without issue. >> However, if I install it as a service using the same parameters, it stops >> sending data to the collector after a few hours. The service is still >> running but the collector doesn't receive any flows. >> >> Has anyone seen this issue or have any ideas what I can try next? >> >> The services were configured using the following: >> >> nprobe.exe /i nProbe-16 -n 172.19.91.80:2055 <http://172.19.91.80:2055/> -i >> 3 -u 16 -Q 0 -L 172.16.0.0/16 <http://172.16.0.0/16> -r >> nprobe.exe /i nProbe-17 -n 172.19.91.80:2055 <http://172.19.91.80:2055/> -i >> 1 -u 17 -Q 0 -L 172.17.0.0/16 <http://172.17.0.0/16> -r >> >> Kind regards >> Steve >> >> >> _______________________________________________ >> Ntop-misc mailing list >> [email protected] <mailto:[email protected]> >> http://listgateway.unipi.it/mailman/listinfo/ntop-misc >> <http://listgateway.unipi.it/mailman/listinfo/ntop-misc> > > _______________________________________________ > Ntop-misc mailing list > [email protected] <mailto:[email protected]> > http://listgateway.unipi.it/mailman/listinfo/ntop-misc > <http://listgateway.unipi.it/mailman/listinfo/ntop-misc> > > _______________________________________________ > Ntop-misc mailing list > [email protected] > http://listgateway.unipi.it/mailman/listinfo/ntop-misc
_______________________________________________ Ntop-misc mailing list [email protected] http://listgateway.unipi.it/mailman/listinfo/ntop-misc
