Gerhard, The filter is correct and properly parsed by ntopng. So what is the issue you are experiencing?
Simone On Thu, Jan 5, 2017 at 7:58 PM, Gerhard Mourani <gmour...@prival.ca> wrote: > This doesn't work for me, I'm using the following parameters to exclude > 10.0.0.39 which is my ntopng server IP: > --packet-filter "ip and not proto ipv6 and not ether host > ff:ff:ff:ff:ff:ff and not net (224.0.0.0/8 or 239.0.0.0/8) and not > host 10.0.0.39" > > Gerhard, > > On Jan 5, 2017, at 12:09 PM, brett.sti...@cargocarriers.co.zw wrote: > > Thank you Simone. > > I will try that tomorrow morning. > > Much appreciated. > > > > On January 5, 2017 6:40:25 PM GMT+02:00, Simone Mainardi < > maina...@ntop.org> wrote: > > Brett, the filter is not complete. If you want to exclude 10.0.50.246 > set: > > --packet-filter="not host 10.0.50.246" > > If you look at the ntopng output you will see if the filter is parsed > correctly. > > > > > On Thu, Jan 5, 2017 at 4:05 PM, Brett Stiell (CCIH) < > brett.sti...@cargocarriers.co.zw> wrote: > > Hi there. > > > > Thanks for getting back to me > > > > This is the contents of my ntopng.start file:- > > > > -G=/var/run/ntopng.pid > > --daemon= > > --local-networks="10.0.50.0/25,10.0.50.128/26,10.0.50.193/30" > > --packet-filter 10.0.50.246 > > -m "10.0.50.0/25,10.0.50.128/26,10.0.50.193/30" > > --track-local-hosts > > > > Regards, > > > > Brett > > > > *From:* Simone Mainardi [mailto:maina...@ntop.org] > *Sent:* Thursday, January 05, 2017 3:26 PM > *To:* n...@unipi.it > *Cc:* ntop mailing list > *Subject:* Re: [Ntop] Excluding hosts or a subnet from being > > monitored > > > > > Hi, > > > > --packet-filter is the proper way to do that. Can you please report > > the > > exact filter you specified? Also check (and paste) ntopng output. > > ntopng > > prints a confirmation message if it has successfully parsed the > > filter. > > > > > Regards > > Simone > > > > On Thu, Jan 5, 2017 at 11:14 AM, Brett Stiell (CCIH) < > brett.sti...@cargocarriers.co.zw> wrote: > > Hi. > > > > Is there any way to exclude a subnet or a range of hosts from being > monitored and appearing on the dashboard etc. > > > > Our servers are in a specific IP range and I am not interested in > receiving their usage data. > > > > I tried –B and –packet-filter and “not” but they don’t seem to work. > > > > Thanks > > > _______________________________________________ > Ntop mailing list > Ntop@listgateway.unipi.it > http://listgateway.unipi.it/mailman/listinfo/ntop > > > > > -- > Sent from my Android device with Email Mail. Please excuse my > brevity._______________________________________________ > Ntop mailing list > Ntop@listgateway.unipi.it > http://listgateway.unipi.it/mailman/listinfo/ntop > > >
_______________________________________________ Ntop mailing list Ntop@listgateway.unipi.it http://listgateway.unipi.it/mailman/listinfo/ntop