Is it just a point to point layer 2? I've not dealt with Qwest in a long time, so I'm not familiar with their offerings.
Jonathan L. Raper, A+, MCSA, MCSE Technology Coordinator Eagle Physicians & Associates, PA jra...@eaglemds.com<BLOCKED::mailto:%20jra...@eaglemds.com> www.eaglemds.com<BLOCKED::http://www.eaglemds.com/> ________________________________ From: Eldridge, Dave [mailto:d...@parkviewmc.com] Sent: Wednesday, January 05, 2011 9:40 AM To: NT System Admin Issues Subject: RE: Metro Ethernet ? Jonathan, I am switching over from our 10mb to 100mb qmoe starting with my signoff next week. They are (Qwest) still trying to get the circuit to verify at 100Mb. It currently to them shows 82. How can I can test this with just a pc on my end? I went to qwest.speedtest.net and it isn't anywhere near even the 82 they report. How do I the customer validate the speed I am paying for? dave From: Raper, Jonathan - Eagle [mailto:jra...@eaglemds.com] Sent: Wednesday, January 05, 2011 7:33 AM To: NT System Admin Issues Subject: RE: Metro Ethernet ? We switched to Metro-E over fiber about 6 years ago, and haven't looked back, though it isn't MPLS. We just have a Point to Multi-point layer 2 network, with them breaking out switch ports at my core for each remote site. So for all intents and purposes, from my standpoint, it is a handful of point to point layer 2 connections. One thing I had to beat into my providers' head was verifying the speed and duplex of their equipment. For some, we needed 100 full, and for others, we needed 10 full. It all depended on what gear we had at each site. Even once the setting was changed, sometimes it would take an equipment reboot (theirs AND ours) in order for it to settle properly. You should not have to dumb down the connection speed to 10 mbps, as they are rate limiting on their equipment down to 5 Mbps (just like what we have). What is your terminating equipment, and are you seeing interface errors? (I know you said collisions, but what exactly are your interfaces saying?) Jonathan L. Raper, A+, MCSA, MCSE Technology Coordinator Eagle Physicians & Associates, PA jra...@eaglemds.com<BLOCKED::mailto:%20jra...@eaglemds.com> www.eaglemds.com<BLOCKED::http://www.eaglemds.com/> ________________________________ From: Tom Miller [mailto:tmil...@hnncsb.org] Sent: Wednesday, January 05, 2011 9:21 AM To: NT System Admin Issues Subject: Metro Ethernet ? Folks, I am converting our network from point to point to MVLS/Metro Ethernet. What I am noticing at some sites is that performance is worse that with the point to point circuit. Ping times greatly increased, collisions, etc. I've been working with my provider to get this resolved. First they thought it was a speed mismatch issue, so the provider's equipment and my equipment were changed to the same setting (full 100). That's not working and now we'll probably change it to full 10 (since the allocation is 5 Mbps anyway). I can also do some rate shaping on my switches, but it's a PITA and I was hoping to avoid it. Anyone else have these issues with conversion? Some sites are fine, others are not. All have same switches, model, firmware, config for trunk ports. I haven't pulled out my bag o software to look at what's on the pipe, anyone have any that would be best for this scenario? I have Praesser but I really need a site to site test/analysis tool. I just downloaded Qcheck and will see if that does it. I've also asked my provider to give me some statistics on traffic they see. Recommendations and comments welcome. Tom Miller Engineer, Information Technology Hampton-Newport News Community Services Board 757-788-0528 Confidentiality Notice: This e-mail message, including attachments, is for the sole use of the intended recipient(s) and may contain confidential and privileged information. Any unauthorized review, use, disclosure, or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply e-mail and destroy all copies of the original message. ~ Finally, powerful endpoint security that ISN'T a resource hog! ~ ~ <http://www.sunbeltsoftware.com/Business/VIPRE-Enterprise/> ~ --- To manage subscriptions click here: http://lyris.sunbelt-software.com/read/my_forums/ or send an email to listmana...@lyris.sunbeltsoftware.com<mailto:listmana...@lyris.sunbeltsoftware.com> with the body: unsubscribe ntsysadmin ________________________________ Any medical information contained in this electronic message is CONFIDENTIAL and privileged. It is unlawful for unauthorized persons to view, copy, disclose, or disseminate CONFIDENTIAL information. This electronic message may contain information that is confidential and/or legally privileged. It is intended only for the use of the individual(s) and/or entity named as recipients in the message. If you are not an intended recipient of this message, please notify the sender immediately and delete this material from your computer. Do not deliver, distribute or copy this message, and do not disclose its contents or take any action in reliance on the information that it contains. ~ Finally, powerful endpoint security that ISN'T a resource hog! ~ ~ <http://www.sunbeltsoftware.com/Business/VIPRE-Enterprise/> ~ --- To manage subscriptions click here: http://lyris.sunbelt-software.com/read/my_forums/ or send an email to listmana...@lyris.sunbeltsoftware.com<mailto:listmana...@lyris.sunbeltsoftware.com> with the body: unsubscribe ntsysadmin This e-mail contains the thoughts and opinions of the sender and does not represent official Parkview Medical Center policy. This communication is intended only for the recipient(s) named above, may be confidential and/or legally privileged: and, must be treated as such in accordance with state and federal laws. If you are not the intended recipient, you are hereby notified that any use of this communication, or any of its contents, is prohibited. If you have received this communication in error, please return to sender and delete the message from your computer system.{token} ~ Finally, powerful endpoint security that ISN'T a resource hog! ~ ~ <http://www.sunbeltsoftware.com/Business/VIPRE-Enterprise/> ~ --- To manage subscriptions click here: http://lyris.sunbelt-software.com/read/my_forums/ or send an email to listmana...@lyris.sunbeltsoftware.com<mailto:listmana...@lyris.sunbeltsoftware.com> with the body: unsubscribe ntsysadmin ~ Finally, powerful endpoint security that ISN'T a resource hog! ~ ~ <http://www.sunbeltsoftware.com/Business/VIPRE-Enterprise/> ~ --- To manage subscriptions click here: http://lyris.sunbelt-software.com/read/my_forums/ or send an email to listmana...@lyris.sunbeltsoftware.com with the body: unsubscribe ntsysadmin
