BTW, I already started x-server with windowmaker :) assuming that I have 1024 mb of vide memory, 640x480 mode with 60 hz frequency :) It seems there is no pci cards, and I was in trouble what to write as a BUS id, then just commented that line ;0
Then, I can't do right clicks in windowmaker :) I changed the mouse buttons from config, so now I can run windowmaker menu with left click and select windows with right click :) Anyway, how do I emulate right click with it? Do linux understand ps/2 attached to the ps/2 port? It there compatible protocol? Thanks On 4/6/06, Norayr Chilingaryan <[EMAIL PROTECTED]> wrote: > Hi all > Thank you all for support > About two month ago I wrote in this mailing list about troubles > installing debian sarge on my powerbook 5300cs > Yesterday my frienad returned from US and brought 56mb ram for me. > I installed it in the powerbook immediately and during this night > successfully installed debian sarge on it :) > I am already quite happy with it, but however have a few postinstall questions > > 1. I can't use modules of debian default kernel. > Should I try to hack /lib/modules/2.4.27-powerpc to rename it to > 2.4.27 and hack all files like modules.dep to try to load some kernel > modules? > For instance I may need to load slip module or may be ppp modules, if > ppp doesn't compiled into kernel already. > > 2. Is it possible to have an x server or sound working? > if yes, which keyboard, wich video card with how much memory, and wich > monitor should I select when xf86config ? > > 3. ona the nubus-powermac main page there are information about > supported hardware. > does it mean that all that drivers already compiled into miboot.image ? > > 4. to change the kernel I should download nubus-powemac kernel > sources, recompile it without modules at all, compile in all drivers I > need statically, and copy it to /dev/hda7/ partition in Linux kernels > folder? > > Now I'll try to copy default debian kernel there and boot it, but > almost sure that there is no reason to do it, because that kernel will > not support nubus :) > > > Thanks :) > > thanks for all again :) > > Beste wishes > > Norayr > > On 2/5/06, Tobias Netzel <[EMAIL PROTECTED]> wrote: > > Hello Norayr, > > > > at least now you can boot your PB from floppy disk and CD-ROM. > > As there is no CD-ROM driver on the boot floppy you need to do a > > special trick that at least works with the IDE CD-ROM drives in the > > PowerBook 1400 (which is nearly identical to the PB5300). > > - insert both the MacOS CD-ROM and the boot floppy and reboot. > > - the computer should now boot from the floppy - if not try keeping the > > mouse button pressed (after the startup sound) until it boots from the > > floppy. > > - with the CD-ROM in the drive now there should be a CD-ROM driver > > loaded and the CD-ROM should show up on the Desktop. > > - now copy the contents of the miboot CD to the harddisk (the miboot > > partition needn't be larger than 10 MB - if it's larger create a > > smaller one). > > - if the harddisk doesn't show up you need to format it with Drive > > Setup or reboot to let the finder ask for formatting. > > - open the System Folder on the harddisk in order to make it the active > > one (it must have the MacOS logo on it). > > - remove the floppy and CD from the drives and reboot. > > - miboot should boot now. > > - follow the instructions in the release notes of the miboot ISO. > > > > I hope this will help you. > > > > Tobias > > > > Am 05.02.2006 um 14:02 schrieb Norayr Chilingaryan: > > > > > > > > Hello! > > > > > > On 2/5/06, Florian Boelstler <[EMAIL PROTECTED]> wrote: > > >> > > >> Norayr Chilingaryan wrote: > > >> > again, the same issue, I have downloaded iso latest iso image from > > >> > sourceforge with wget, and wrote it to cd using cdrecord > > >> > [...] > > >> > > >> I just downloaded the ISO image again (using the link in your message) > > >> and compared it with my local copy that I uploaded to SF. > > >> The ISO is definitely OK. > > >> > > >> I have successfully applied that ISO recorded on a CD-R. > > >> Though I was using k3b to burn it (using default settings: Extras -> > > >> Burn CD image). > > >> > > >> Florian > > >> > > > > > > Very interesting! > > > I can't write it using k3b 0.11.24, because when I opened image > > > Tools->CD->Burn cd image > > > k3b doesn't check md5 sum check claims "seems not to be a usable > > > image" and burn button is disable so it seems impossible to write it > > > using k3b :) > > > > > > What does it mean? > > > > > > Thanks > > > > > > Norayr > > > > > > > > ------------------------------------------------------- This SF.Net email is sponsored by xPML, a groundbreaking scripting language that extends applications into web and mobile media. Attend the live webcast and join the prime developer group breaking into this new coding territory! http://sel.as-us.falkag.net/sel?cmd=lnk&kid0944&bid$1720&dat1642 _______________________________________________ Nubus-pmac-users mailing list Nubus-pmac-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/nubus-pmac-users
