Hi, again! Today I tried again tinkering around my UPS, but now the message is different:
upsdrvctl start Network UPS Tools - UPS driver controller 2.2.2 Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec_usb] Carlos Rodrigues (c) 2003-2008 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) 2007 Megatec protocol UPS detected. Startup timer elapsed, continuing... What to do now? brgds Janeks ----- Original Message ----- From: "Janeks Kamerovskis" <[EMAIL PROTECTED]> To: "Alexander I. Gordeev" <[EMAIL PROTECTED]> Cc: <[email protected]> Sent: Thursday, November 06, 2008 9:08 PM Subject: Re: [Nut-upsuser] Mustek PowerMust 600 USB configuration > Thanks, Alexander for your help! > > Finaly I got to manage to compile NUT. > > Now I am configuring it: > my ups.conf: > [mustekUPS] > driver = megatec_usb > port = /dev/usb/hiddev0 > # port = auto > desc = "Mustek PowerMust 600 USB" > > But I am getting errors: > > /usr/local/ups/bin/upsdrvctl start > Network UPS Tools - UPS driver controller 2.2.2 > Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec_usb] > Carlos Rodrigues (c) 2003-2008 > > Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] > Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) > 2007 > > ser_send_pace: Device detached? (error -1: error sending control message: > Operation not permitted) > Successfully reconnected > ser_send_pace: Device detached? (error -1: error sending control message: > Operation not permitted) > Successfully reconnected > ser_send_pace: Device detached? (error -1: error sending control message: > Operation not permitted) > Successfully reconnected > ser_send_pace: Device detached? (error -1: error sending control message: > Operation not permitted) > Successfully reconnected > ser_send_pace: Device detached? (error -1: error sending control message: > Operation not permitted) > Successfully reconnected > Megatec protocol UPS not detected. > Driver failed to start (exit status=1) > > Also I am not shure how to configure hotplugging scripts for permissions. > I did like for serial ports using /dev/usb/diddev0 > Could you give me some advice/link? > > brgds > Janeks > > ----- Original Message ----- > From: "Alexander I. Gordeev" <[EMAIL PROTECTED]> > To: "Janeks Kamerovskis" <[EMAIL PROTECTED]> > Cc: <[email protected]> > Sent: Wednesday, November 05, 2008 1:14 AM > Subject: Re: [Nut-upsuser] Mustek PowerMust 600 USB configuration > > >> I've updated the packages: >> http://lvk.cs.msu.su/~lasaine/nut-backport/lenny/nut_2.2.2-6.2~stable1_powerpc.deb >> http://lvk.cs.msu.su/~lasaine/nut-backport/lenny/libupsclient1_2.2.2-6.2~stable1_powerpc.deb >> >> There are also over packages if needed here: >> http://lvk.cs.msu.su/~lasaine/nut-backport/lenny/ >> >> On Wednesday 05 November 2008 00:28:23 you wrote: >>> Thanks, Alexander! >>> >>> I tried both ways: >>> Both of them are asking for additional packages/libraries. >>> >>> Do I need them at all? I am asking so because Bubba is device without >>> monitor i.e. no GUI things only ssh acces or web GUIs. >>> >>> The console copy: >>> >> [snip] >>> bubba:/home/janeks/dls# apt-get install libgd2-xpm-dev >>> Reading package lists... Done >>> Building dependency tree... Done >>> You might want to run `apt-get -f install' to correct these: >>> The following packages have unmet dependencies: >>> libgd2-xpm-dev: Depends: libfontconfig1-dev but it is not going to be >>> installed >>> Depends: libfreetype6-dev but it is not going to be >>> installed >>> Depends: libpng12-0-dev >>> Depends: libx11-dev but it is not going to be >>> installed or >>> xlibs-dev (< 4.3.0) but it is not installable >>> Depends: libxpm-dev but it is not going to be >>> installed or >>> xlibs-dev (< 4.3.0) but it is not installable >>> nut: Depends: libupsclient1 but it is not installable >>> Depends: udev (>= 0.124-1) but 0.105-4 is to be installed >>> E: Unmet dependencies. Try 'apt-get -f install' with no packages (or >>> specify a solution). >> >> I thought you have X server. Use libgd2-noxpm-dev instead. >> >> -- >> Alexander > > > _______________________________________________ > Nut-upsuser mailing list > [email protected] > http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
