We are using OCFS2 on Red Hat Enterprise Linux to share regular UNIX filesystems between three web servers and this seems to work reasonably well except that we frequently experience high load situations on our servers (all at the same time).
The underlying SAN is an HP EVA 4100 and the SAN diagnostics show that the SAN itself is coping fairly easily; CPU loads on the controllers rarely rise above 5% but usually steady at around 1%. The number of read requests per second is usually around 500-600 although this does peak occasionally at 2000-3000. On one occasion the number of requests per second went over 12,000 with an average of 52MB/s transferred; the SAN coped with this with an average latency of 0.1ms. Write requests rarely go higher than 20-30 per second but have been known to hit 2500 during busy periods. Because we are web-serving, this results in lots of read requests for small files for the majority of the time but there are periods in the day when we update many thousands of images and it is at times like this when we are doing a relatively high volume of writes that the load shoots up. We recently has a situation where the 1 minute load average hit 650. Normally when we hit high load situations, the load seems to be higher on the nodes that aren't writing to the SAN than on the one that is. Running 'iostat -x' frequently shows output similar to that below: Time: 08:05:48 AM Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 46.40 255.80 250.40 28.00 2373.60 2267.60 16.67 1.44 5.16 3.24 90.26 Time: 08:05:53 AM Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 18.47 104.22 221.49 232.93 1902.41 2699.40 10.13 2.68 5.78 2.00 90.82 Time: 08:05:58 AM Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 28.60 44.20 47.40 2.40 613.60 98.00 14.29 5.40 104.24 20.09 100.04 Time: 08:06:03 AM Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 38.80 10.20 149.80 3.00 1517.20 373.40 12.37 3.71 25.98 6.34 96.86 This situation goes on for several minutes or tens of minutes before things calm down again. The number of reads and writes per second don't seem to be unreasonably high to me, especially considering the underlying SAN performance but it is clear that the device is totally saturated with elevated figures for await and svctm. The 1 minute load averages at these times is typically 60-80 and so it seems clear to me that we are running out of steam. Oddly, vmstat doesn't indicate blocked processes or waiting on I/O during these times. CPU utilization is never more than about 20% (the servers were considerably over-spec'ed with 4 quad-core Xeon processors in each and 8GB RAM. There is no swapping taking place either. BTW, I have mounted the SAN-based filesystems with noatime and this has helped a little. It occurred to me that maybe it was the inter-node communications to negotiate locks that may be slowing things down but the servers are connected via Gigabit NICs and all are on the same subnet so network switches can be ruled out. My question is: is OCFS2 (or any clustered filesystem for that matter) suitable for the demands that we are placing on it? Has anyone any experience of using OCFS2 under what I assume to be 'extreme' conditions? Any advice would be greatly appreciated - this is causing me untold grief due to poor response times from the web servers when this is happening. On a few occasions, when the load was particularly high, one or other of the web servers have fenced and rebooted themselves. Regards, Mick.
_______________________________________________ Ocfs2-users mailing list [email protected] http://oss.oracle.com/mailman/listinfo/ocfs2-users
