Is the pool usable during comstar hang? Can you write and read from the pool (test both, in my case, when pool froze, I wasn’t able to write to the pool, but I could read).
Again, this might not be connected with Comstar, but in my case, Comstar and pool hang were exchanging. Matej > On 08 Jan 2016, at 20:11, Brian Hechinger <wo...@4amlunch.net> wrote: > > Yeah, I’m using the 1068E to boot from (this has been supported since before > Illumos) but that doesn’t have anything accessed by COMSTAR. > > It’s the ICH10R SATA that hosts the disks that COMSTAR shares out space from. > > -brian > >> On Jan 8, 2016, at 1:31 PM, Richard Jahnel <rjah...@ellipseinc.com> wrote: >> >> First off, love SuperMicro good choice IMHO. >> >> This board has two on board controllers. >> >> LSI SAS1068E (not 100% sure there are working illumos drivers for this one) >> >> And >> >> Intel ICH10R SATA (So I'm guessing your using this one.) >> >> -----Original Message----- >> From: OmniOS-discuss [mailto:omnios-discuss-boun...@lists.omniti.com] On >> Behalf Of Brian Hechinger >> Sent: Friday, January 08, 2016 12:16 PM >> To: Matej Zerovnik <ma...@zunaj.si> >> Cc: omnios-discuss <omnios-discuss@lists.omniti.com> >> Subject: Re: [OmniOS-discuss] [discuss] COMSTAR hanging >> >> >>> Which controller exactly do you have? >> >> Whatever ACHI stuff is built into the motherboard. Motherboard is X8DTL-3F. >> >>> Do you know firmware version? >> >> I’m assuming this is linked to the BIOS version? >> >>> Which hard drives? >> >> Hitachi-HUA723030ALA640-MKAOAA50-2.73TB >> >>> It might not tell much, but it’s good to have as much information as >>> possible. >>> >>> When comstar hangs, can you telnet to the iSCSI port? >>> What does svcs says, is the service running? >>> What happens in you try to restart it? >>> How do you restart it? >> >> I’ll try all these things next time. >> >>> In my case, svcs reported service running, but when I tried to telnet, >>> there was no connection as well as there was no listening port opened when >>> checking with 'netstat -an'. If I tried to restart target and stmf service, >>> but stmf service got stucked in online* state and would not start. Reboot >>> was the only solution in my case, but as I said, latest 014 release is >>> working OK (but then again, load got reduced). >> >> All good info. Thanks! >> >> -brian >> >>> >>> Matej >>> >>>> On 08 Jan 2016, at 17:50, Dave Pooser <dave...@pooserville.com> wrote: >>>> >>>>>> On Jan 8, 2016, at 11:22 AM, Brian Hechinger <wo...@4amlunch.net> wrote: >>>>>> >>>>>> No, ZFS raid10 >>>>> >>>>> Saw the HW-RAID term, and got concerned. That's what, raidz2 in ZFS-ese? >>>> >>>> It's a zpool with multiple mirror vdevs. >>>> >>>> -- >>>> Dave Pooser >>>> Cat-Herder-in-Chief, Pooserville.com >>>> >>>> >>>> _______________________________________________ >>>> OmniOS-discuss mailing list >>>> OmniOS-discuss@lists.omniti.com >>>> http://lists.omniti.com/mailman/listinfo/omnios-discuss >>> >>> _______________________________________________ >>> OmniOS-discuss mailing list >>> OmniOS-discuss@lists.omniti.com >>> http://lists.omniti.com/mailman/listinfo/omnios-discuss >> >> _______________________________________________ >> OmniOS-discuss mailing list >> OmniOS-discuss@lists.omniti.com >> http://lists.omniti.com/mailman/listinfo/omnios-discuss >
smime.p7s
Description: S/MIME cryptographic signature
_______________________________________________ OmniOS-discuss mailing list OmniOS-discuss@lists.omniti.com http://lists.omniti.com/mailman/listinfo/omnios-discuss