Have you tried increasing the disk readahead value? #blockdev --setra X /dev/<multipath device>
The default is 256. Use --getra to see current setting. Setting it too high will probably hurt your database performance. Since databases tend to be random, not sequential. Don On Fri, Apr 24, 2009 at 11:07 AM, jnantel <nan...@hotmail.com> wrote: > > If you recall my thread on tuning performance for writes. Now I am > attempting to squeeze as much read performance as I can from my > current setup. I've read a lot of the previous threads, and there has > been mention of "miracle" settings that resolved slow reads vs > writes. Unfortunately, most posts reference the effects and not the > changes. If I were tuning for read performance in the 4k to 128k > block range what would the best way to go about it? > > Observed behavior: > - Read performance seems to be capped out at 110meg/sec > - Write performance I get upwards of 190meg/sec > > Tuning options I'll be trying: > block alignment (stride) > Receiving buffers > multipath min io changes > iscsi cmd depth > > > Hardware: > 2 x Cisco 3750 with 32gig interconnect > 2 x Dell R900 with 128gig ram and 1 broadcom Quad (5709) and 2 dual > port intels (pro 1000/MT) > 2 x Dell Equallogic PS5000XV with 15 x SAS in raid 10 config > > > multipath.conf: > > device { > vendor "EQLOGIC" > product "100E-00" > path_grouping_policy multibus > getuid_callout "/sbin/scsi_id -g -u -s /block/%n" > features "1 queue_if_no_path" > path_checker readsector0 > failback immediate > path_selector "round-robin 0" > rr_min_io 128 > rr_weight priorities > } > > iscsi settings: > > node.tpgt = 1 > node.startup = automatic > iface.hwaddress = default > iface.iscsi_ifacename = ieth10 > iface.net_ifacename = eth10 > iface.transport_name = tcp > node.discovery_address = 10.1.253.10 > node.discovery_port = 3260 > node.discovery_type = send_targets > node.session.initial_cmdsn = 0 > node.session.initial_login_retry_max = 4 > node.session.cmds_max = 1024 > node.session.queue_depth = 128 > node.session.auth.authmethod = None > node.session.timeo.replacement_timeout = 120 > node.session.err_timeo.abort_timeout = 15 > node.session.err_timeo.lu_reset_timeout = 30 > node.session.err_timeo.host_reset_timeout = 60 > node.session.iscsi.FastAbort = Yes > node.session.iscsi.InitialR2T = No > node.session.iscsi.ImmediateData = Yes > node.session.iscsi.FirstBurstLength = 262144 > node.session.iscsi.MaxBurstLength = 16776192 > node.session.iscsi.DefaultTime2Retain = 0 > node.session.iscsi.DefaultTime2Wait = 2 > node.session.iscsi.MaxConnections = 1 > node.session.iscsi.MaxOutstandingR2T = 1 > node.session.iscsi.ERL = 0 > node.conn[0].address = 10.1.253.10 > node.conn[0].port = 3260 > node.conn[0].startup = manual > node.conn[0].tcp.window_size = 524288 > node.conn[0].tcp.type_of_service = 0 > node.conn[0].timeo.logout_timeout = 15 > node.conn[0].timeo.login_timeout = 15 > node.conn[0].timeo.auth_timeout = 45 > node.conn[0].timeo.noop_out_interval = 10 > node.conn[0].timeo.noop_out_timeout = 30 > node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 > node.conn[0].iscsi.HeaderDigest = None,CRC32C > node.conn[0].iscsi.DataDigest = None > node.conn[0].iscsi.IFMarker = No > node.conn[0].iscsi.OFMarker = No > > /etc/sysctl.conf > > net.core.rmem_default= 65536 > net.core.rmem_max=2097152 > net.core.wmem_default = 65536 > net.core.wmem_max = 262144 > net.ipv4.tcp_mem= 98304 131072 196608 > net.ipv4.tcp_window_scaling=1 > > # > # Additional options for Oracle database server > #ORACLE > kernel.panic = 2 > kernel.panic_on_oops = 1 > net.ipv4.ip_local_port_range = 1024 65000 > net.core.rmem_default=262144 > net.core.wmem_default=262144 > net.core.rmem_max=524288 > net.core.wmem_max=524288 > fs.aio-max-nr=524288 > > > > > --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to open-iscsi@googlegroups.com To unsubscribe from this group, send email to open-iscsi+unsubscr...@googlegroups.com For more options, visit this group at http://groups.google.com/group/open-iscsi -~----------~----~----~----~------~----~------~--~---