I finished this project a while back, and I extend my apologies. I forgot about the netmask issue. I had that same problem when I did it, I was going down the wrong path.
On 10/17/07, Abhayjeet Singh Grewal <[EMAIL PROTECTED]> wrote: > > Thanks a million sir. > You have no idea, how happy I am to see the iscsi-ls output. This was > tricky one, I would have never thought of MASK to be a problem. I understand > that now and would setup my other nodes tomorrow and continue to configure > Oracle cluster. > > If you ever plan to visit India, Delhi, just let me know. > > Cheers !!!! > > > > On 10/17/07, Rafiu Fakunle <[EMAIL PROTECTED]> wrote: > > > > Abhayjeet Singh Grewal wrote: > > > I have checked the initiator, I could not see anything wrong. > > > > > > These are test servers, if you could putty and see yourself it would > > be > > > really helpfull > > > https://61.246.5.203:446/ > > > IP open filer: 61.246.5.203 > > > user: root > > > password: cdsfiler > > > > > > for racnode3 > > > user: root > > > password: centos > > > > > > > Seems to be a netmask issue. Set netmask to 255.255.255.255 for each > > node in openfiler network ACL. > > > > > > [EMAIL PROTECTED] ~]# cat /proc/scsi/scsi > > Attached devices: > > Host: scsi0 Channel: 00 Id: 00 Lun: 00 > > Vendor: Openfile Model: Virtual disk Rev: 0 > > Type: Direct-Access ANSI SCSI revision: 04 > > Host: scsi2 Channel: 00 Id: 00 Lun: 00 > > Vendor: Openfile Model: Virtual disk Rev: 0 > > Type: Direct-Access ANSI SCSI revision: 04 > > Host: scsi1 Channel: 00 Id: 00 Lun: 00 > > Vendor: Openfile Model: Virtual disk Rev: 0 > > Type: Direct-Access ANSI SCSI revision: 04 > > Host: scsi3 Channel: 00 Id: 00 Lun: 00 > > Vendor: Openfile Model: Virtual disk Rev: 0 > > Type: Direct-Access ANSI SCSI revision: 04 > > > > R, > > > > > On 10/17/07, Rafiu Fakunle <[EMAIL PROTECTED]> wrote: > > > > > >> Abhayjeet Singh Grewal wrote: > > >> > > >>> [EMAIL PROTECTED] iet]# cat session > > >>> tid:5 name:iqn.2006-01.com.openfiler:rac1.asm4 > > >>> tid:4 name:iqn.2006-01.com.openfiler:rac1.asm3 > > >>> tid:3 name:iqn.2006-01.com.openfiler:rac1.asm2 > > >>> tid:2 name:iqn.2006-01.com.openfiler:rac1.asm1 > > >>> tid:1 name:iqn.2006-01.com.openfiler:rac1.crs > > >>> [EMAIL PROTECTED] iet]# cat volume > > >>> tid:5 name:iqn.2006-01.com.openfiler:rac1.asm4 > > >>> lun:0 state:0 iotype:fileio iomode:wt path:/dev/rac1/asm4 > > >>> tid:4 name:iqn.2006-01.com.openfiler:rac1.asm3 > > >>> lun:0 state:0 iotype:fileio iomode:wt path:/dev/rac1/asm3 > > >>> tid:3 name:iqn.2006-01.com.openfiler:rac1.asm2 > > >>> lun:0 state:0 iotype:fileio iomode:wt path:/dev/rac1/asm2 > > >>> tid:2 name:iqn.2006-01.com.openfiler:rac1.asm1 > > >>> lun:0 state:0 iotype:fileio iomode:wt path:/dev/rac1/asm1 > > >>> tid:1 name:iqn.2006-01.com.openfiler:rac1.crs > > >>> lun:0 state:0 iotype:fileio iomode:wt path:/dev/rac1/crs > > >>> > > >>> > > >> All's well on the Openfiler target front. Check your initiator > > settings. > > >> > > >> > > >> R. > > >> > > >> > > >>> On 10/17/07, Rafiu Fakunle <[EMAIL PROTECTED]> wrote: > > >>> > > >>> > > >>>> Abhayjeet Singh Grewal wrote: > > >>>> > > >>>> > > >>>> > > >>>> > > >>>>> Hi, > > >>>>> I tried everything to best of knowledge and am not able to mount > > iscsi > > >>>>> device on client. Node connects to target and show connection > > >>>>> > > >>>>> > > >>>> established > > >>>> > > >>>> > > >>>>> but does nothing. In my administration page of openfiler evrything > > is > > >>>>> > > >>>>> > > >>>> good > > >>>> > > >>>> > > >>>>> and status page for iscsi it show LV but under intitiator > > connection > > >>>>> > > >>>>> > > >>>> shows > > >>>> > > >>>> > > >>>>> nothing. I have given the dump of the things below. > > >>>>> > > >>>>> Please help me. > > >>>>> > > >>>>> > > >>>>> > > >>>>> > > >>>> Pls show output of following commands: > > >>>> > > >>>> 1) cat /proc/net/iet/sessions > > >>>> 2) cat /proc/net/iet/volumes > > >>>> > > >>>> > > >>>> R. > > >>>> > > >>>> > > >>>> > > >>>> > > >>>>> ----My Node Info --- > > >>>>> > > >>>>> [ [EMAIL PROTECTED] etc]# ifconfig > > >>>>> eth1 Link encap:Ethernet HWaddr 00:19:5B:FD:14:E0 > > >>>>> inet addr:192.168.2.82 Bcast: 192.168.2.255 Mask: > > >>>>> > > >>>>> > > >>>> 255.255.255.0 > > >>>> > > >>>> > > >>>>> inet6 addr: fe80::219:5bff:fefd:14e0/64 Scope:Link > > >>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > >>>>> RX packets:15928 errors:0 dropped:0 overruns:0 frame:0 > > >>>>> TX packets:13635 errors:0 dropped:0 overruns:0 carrier:0 > > > > >>>>> collisions:0 txqueuelen:1000 > > >>>>> RX bytes:8249769 (7.8 MiB) TX bytes:2492548 (2.3 MiB) > > >>>>> Interrupt:209 Base address:0xc00 > > >>>>> > > >>>>> lo Link encap:Local Loopback > > >>>>> inet addr:127.0.0.1 Mask:255.0.0.0 > > >>>>> inet6 addr: ::1/128 Scope:Host > > >>>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 > > >>>>> RX packets:2917 errors:0 dropped:0 overruns:0 frame:0 > > >>>>> TX packets:2917 errors:0 dropped:0 overruns:0 carrier:0 > > >>>>> collisions:0 txqueuelen:0 > > >>>>> RX bytes:4077067 (3.8 MiB) TX bytes:4077067 (3.8 MiB) > > >>>>> > > >>>>> > > >>>>> [ [EMAIL PROTECTED] etc]# uname -ar > > >>>>> Linux racnode3 2.6.9-42.ELsmp #1 SMP Sat Aug 12 09:39:11 CDT 2006 > > i686 > > >>>>> > > >>>>> > > >>>> i686 > > >>>> > > >>>> > > >>>>> i386 GNU/Linux > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# vi iscsi.conf > > >>>>> DiscoveryAddress=192.168.2.195 > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# service iscsi restart > > >>>>> Searching for iscsi-based multipath maps > > >>>>> Found 0 maps > > >>>>> Stopping iscsid: > > [ OK ] > > >>>>> Removing iscsi driver: > > [ OK ] > > >>>>> Checking iscsi config: > > [ OK ] > > >>>>> Loading iscsi > > driver: [ OK ] > > >>>>> Starting iscsid: > > [ OK ] > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# iscsi-ls > > >>>>> > > >>>>> > > >>>>> > > >> > > ******************************************************************************* > > >> > > >>>>> SFNet iSCSI Driver Version ...4:0.1.11-4(15-Jan-2007) > > >>>>> > > >>>>> > > >>>>> > > >> > > ******************************************************************************* > > >> > > >>>>> [EMAIL PROTECTED] etc]#dmesg > > >>>>> iscsi-sfnet: Loading iscsi_sfnet version 4: 0.1.11-3 > > >>>>> iscsi-sfnet: Control device major number 254 > > >>>>> > > >>>>> ----- My Openfiler Info ----- > > >>>>> [EMAIL PROTECTED] etc]# ifconfig > > >>>>> eth0 Link encap:Ethernet HWaddr 00:30:18:A2:A5:61 > > >>>>> inet addr:192.168.2.195 Bcast:192.168.2.255 Mask: > > >>>>> > > >>>>> > > >>>> 255.255.255.0 > > >>>> > > >>>> > > >>>>> inet6 addr: fe80::230:18ff:fea2:a561/64 Scope:Link > > >>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > >>>>> RX packets:11049 errors:0 dropped:0 overruns:0 frame:0 > > >>>>> TX packets:5605 errors:0 dropped:0 overruns:0 carrier:0 > > >>>>> collisions:0 txqueuelen:1000 > > >>>>> RX bytes:7327206 (6.9 Mb) TX bytes:1102959 (1.0 Mb) > > >>>>> Interrupt:17 Base address:0xc000 > > >>>>> > > >>>>> lo Link encap:Local Loopback > > >>>>> inet addr:127.0.0.1 Mask:255.0.0.0 > > >>>>> inet6 addr: ::1/128 Scope:Host > > >>>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 > > >>>>> RX packets:95 errors:0 dropped:0 overruns:0 frame:0 > > >>>>> TX packets:95 errors:0 dropped:0 overruns:0 carrier:0 > > >>>>> collisions:0 txqueuelen:0 > > >>>>> RX bytes:7400 (7.2 Kb) TX bytes:7400 (7.2 Kb) > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# uname -an > > >>>>> Linux openfiler1 2.6.19.7-0.3.smp.gcc3.4.x86.i686 #1 SMP Thu Apr > > 12 > > >>>>> > > >>>>> > > >>>> 02:16:08 > > >>>> > > >>>> > > >>>>> EDT 2007 i686 i686 i386 GNU/Linux > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# netstat -an| grep ESTABLISHED > > >>>>> tcp 0 0 192.168.2.195:3260 192.168.2.82:33340 > > >>>>> ESTABLISHED > > >>>>> tcp 827356 0 192.168.2.195:54729 38.100.0.20:80 > > >>>>> ESTABLISHED > > >>>>> tcp 0 52 ::ffff:192.168.2.195:22 ::ffff: > > >>>>> > > >>>>> > > >>>> 192.168.2.:60068ESTABLISHED > > >>>> > > >>>> > > >>>>> [EMAIL PROTECTED] etc]# lvscan > > >>>>> ACTIVE '/dev/rac1/crs' [2.00 GB] inherit > > >>>>> ACTIVE '/dev/rac1/asm1' [ 115.94 GB] inherit > > >>>>> ACTIVE '/dev/rac1/asm2' [115.94 GB] inherit > > >>>>> ACTIVE '/dev/rac1/asm3' [115.94 GB] inherit > > >>>>> ACTIVE '/dev/rac1/asm4' [ 115.94 GB] inherit > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# vi iscsid.conf > > >>>>> # > > >>>>> # Open-iSCSI default configuration. > > >>>>> # Could be located at /etc/iscsid.conf or ~/.iscsid.conf > > >>>>> # > > >>>>> > > >>>>> node.active_cnx = 1 > > >>>>> node.startup = automatic > > >>>>> > > >>>>> #node.session.auth.username = abhay > > >>>>> #node.session.auth.password = abhay > > >>>>> > > >>>>> node.session.timeo.replacement_timeout = 0 > > >>>>> node.session.err_timeo.abort_timeout = 10 > > >>>>> node.session.err_timeo.reset_timeout = 30 > > >>>>> node.session.iscsi.InitialR2T = No > > >>>>> node.session.iscsi.ImmediateData = Yes > > >>>>> node.session.iscsi.FirstBurstLength = 262144 > > >>>>> node.session.iscsi.MaxBurstLength = 16776192 > > >>>>> node.session.iscsi.DefaultTime2Wait = 0 > > >>>>> node.session.iscsi.DefaultTime2Retain = 0 > > >>>>> node.session.iscsi.MaxConnections = 0 > > >>>>> node.cnx[0].iscsi.HeaderDigest = None > > >>>>> node.cnx[0].iscsi.DataDigest = None > > >>>>> node.cnx[0].iscsi.MaxRecvDataSegmentLength = 65536 > > >>>>> #discovery.sendtargets.auth.authmethod = CHAP > > >>>>> #discovery.sendtargets.auth.username = dima > > >>>>> #discovery.sendtargets.auth.password = aloha > > >>>>> > > >>>>> [EMAIL PROTECTED] etc]# vi initiators.allow > > >>>>> iqn.2006-01.com.openfiler:rac1.crs 192.168.2.26/24, 192.168.2.72/24 > > , > > >>>>> 192.168.2.82/24 > > >>>>> iqn.2006-01.com.openfiler:rac1.asm1 192.168.2.26/24, > > 192.168.2.72/24, > > >>>>> 192.168.2.82/24 > > >>>>> iqn.2006-01.com.openfiler:rac1.asm2 192.168.2.26/24, > > 192.168.2.72/24, > > >>>>> 192.168.2.82/24 > > >>>>> iqn.2006-01.com.openfiler:rac1.asm3 192.168.2.26/24, > > 192.168.2.72/24, > > >>>>> 192.168.2.82/24 > > >>>>> iqn.2006-01.com.openfiler:rac1.asm4 192.168.2.26/24, > > 192.168.2.72/24, > > >>>>> 192.168.2.82/24 > > >>>>> > > >>>>> > > >>>>> Regards, > > >>>>> > > >>>>> Abhay Grewal > > >>>>> > > >>>>> > > >>>>> > > >>>>> > > >> > > ------------------------------------------------------------------------ > > >> > > >>>>> _______________________________________________ > > >>>>> Openfiler-users mailing list > > >>>>> [email protected] > > >>>>> https://lists.openfiler.com/mailman/listinfo/openfiler-users > > >>>>> > > >>>>> > > >>>>> > > >>> > > >> > > > > > > > > > > > > > > > > -- > Regards, > > Abhayjeet Singh Grewal > > V.P. Business Development > Core Database Systems Pvt. Ltd. > > Cell: +91.99103.11114 > www.coredbsystems.com > > _______________________________________________ > Openfiler-users mailing list > [email protected] > https://lists.openfiler.com/mailman/listinfo/openfiler-users > > -- Andrew W. Kerber 'If at first you dont succeed, dont take up skydiving.'
_______________________________________________ Openfiler-users mailing list [email protected] https://lists.openfiler.com/mailman/listinfo/openfiler-users
