but you must see something when you start/stop red5 in order to say why it does not work... other things might be hard to debug from that point.
2008/12/19 Steph <stephane.art...@gmail.com> > > I have a connection error on the localhost:5080 ?? > > > On 19 déc, 12:35, seba.wag...@gmail.com wrote: > > What happens if you run ./red5.sh on fedora? > > > > -- Urspr. Mitt. -- > > Betreff: Re: Bad rooms_id value > > Von: Steph <stephane.art...@gmail.com> > > Datum: 19.12.2008 12:08 > > > > I don't have enought knowledge to do that, how can I have the correct > > hack to run red5 on fedora ? > > Where can I write this value ? > > > > On 19 déc, 09:13, "Sebastian Wagner" <seba.wag...@gmail.com> wrote: > > > > > its r3200 from the red5 repository. > > > you can checkout from red5-repo r3200 and build that on fedora > > > > > anyway I think you should be able to start that on fedora too, if you > know > > > the correct hack to run the red5.sh in fedora. > > > > > sebastian > > > > > 2008/12/19 Steph <stephane.art...@gmail.com> > > > > > > ok thanks Sebastian > > > > it works very well with the last openmeetings version in the SVN. > > > > I have to use the red5_snapshot_r3200, and I don't have any problem > in > > > > Windows side, but this version of red5 doesn't start in my fedora. > > > > Could it be possible to tell me what is this version of red5 (red5 > > > > 0.6.3, 0.7 or 0.8 ???) ! > > > > > > Thanks again > > > > > > Regards > > > > > > On 18 déc, 10:04, "Sebastian Wagner" <seba.wag...@gmail.com> wrote: > > > > > yes that is a known bug and already resolved. > > > > > But I am not sure if its resolved in 0.5.2 or in the SVN only. > > > > > > > sebastian > > > > > > > 2008/12/17 Steph <stephane.art...@gmail.com> > > > > > > > > Hi Sebasdtian, > > > > > > > > I added a room by using the addroom methods, it is worked very > well, > > > > > > but when the value of the rooms_id is bigger than 127, room > doesn't > > > > > > work very well. Is it a known bug ? > > > > > > When the value is smaller than 127, both persons are connected > and the > > > > > > 2 webcams is showed very well. If the value is bigger than 127(I > > > > > > change the value manually in the rooms table), both persons are > > > > > > connected very well, but each person is alone in the room (only > his > > > > > > webcam shown) > > > > > > I installed version 052 without any modification. > > > > > > > > Do you confirm me that bug ? it is very important for me to solve > that > > > > > > very soon or I am wrong once more :) > > > > > > I hope the descritpion of this issue is enought clear. > > > > > > > > Thank you very much for you support > > > > > > > > Steph > > > > > > > -- > > > > > Sebastian > > > > > Wagnerhttp://www.webbase-design.dehttp://openmeetings.googlecode.comhttp:// > > > >www.laszlo-forum.de > > > > > seba.wag...@gmail.com > > > > > -- > > > Sebastian > Wagnerhttp://www.webbase-design.dehttp://openmeetings.googlecode.comhttp://... > > > seba.wag...@gmail.com > > > -- Sebastian Wagner http://www.webbase-design.de http://openmeetings.googlecode.com http://www.laszlo-forum.de seba.wag...@gmail.com --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "OpenMeetings User" group. To post to this group, send email to openmeetings-user@googlegroups.com To unsubscribe from this group, send email to openmeetings-user+unsubscr...@googlegroups.com For more options, visit this group at http://groups.google.com/group/openmeetings-user?hl=en -~----------~----~----~----~------~----~------~--~---