Mahjoub,
I think you are using a very old configuration file. Some of the commands in
the file have changed for OpenOCD 0.4.0. i recommend you use the
configuration files that come with the OpenOCD itself, look for cfg files
corresponding to your board/requirements, in directories board,interface and
target. That should solve most of these problems.
- Nived
On Fri, Sep 17, 2010 at 10:53 AM, Mahjoub Kamel <mahjoubkame...@gmail.com>wrote:
> Thank you for your answer.
> Knowing that i'm new to such developments and at the same time i have to
> accomplish openocd flash programming, i had yet corrected my
> code i succeded only to program the On-chip flash of the lpc2212. by the
> script ".cfg" here attached ( I have only one WARNING to correct it !).
>
>
> flash write_bank 0 X35AU.bin 0x0 ===============>
> Warn : Verification will fail since checksum in image
> (0xe1a00000) to be written to flash is different from calculated vector
> checksum (0xb8
> a06f60).
> Warn : To remove this warning modify build tools on
> developer PC to inject correct LPC vector checksum.
> wrote 1452 bytes from file BootLoader_108.bin to flash bank 0 at offset
> 0x00000000 in 0.187501s (7.562 kb/s)
>
> My serious problem now and three days ago, is to program the external
> flash of the ARM7 LPC2212 based board. This flash is *S29AL016D SPANSION
> 2Mo Nor flash* (normally, we use a CFI method for that) so, i wrote and
> tryed the following code but, there are many error messages displayed for me
> and i couldn't understand them in order to correct them.
>
> I wish you help me to resolve this.
> For OnCHIP ^programming micro i have the following WARNING :
>
>
> I resume my error messages as the following :
>
> flash protect 0 0 0 off =========> Error: auto_probe failed -601
> flash protect 0 0 1 off =========> Error: auto_probe failed -601
> flash protect 0 0 2 off =========> Error: auto_probe failed -601
> flash protect 0 0 3 off =========> Error: auto_probe failed -601
> flash erase_sector 0 0 1 =========> Error: auto_probe failed -601
> flash write_image X35A_20_90.bin 0x8001000 =======> Error: Argument
> overflow
> image.base_address option value
> ('0x80010000') is not valid
> Command handler execution failed
>
> when i change this by :
> flash write_image X35A_20_90.bin 0x0 wrote 0 bytes from file
> X35A_20_90.bin in 0.000000s (nan kb/s)
> Perhaps, i didn't right configured jtag, ram and flash bank as it must be .
>
> Console Error messages, cfg files are attached with this mail.
>
> Note : I have too some cmm good programming files, i can send them to you
> if that make my problem more clear.
>
>
> Yours truly.
>
>
>
> 2010/9/17 Andreas Fritiofson <andreas.fritiof...@gmail.com>
>
> > flash write_binary 0 BootLoader_108.bin 0x0 0: command requires more
>> > arguments
>>
>> There is no command with the name 'flash write_binary'. Perhaps you
>> mean 'flash write_bank'? In that case, the extra zero on the end
>> shouldn't be there. The error message is nonsense.
>>
>> "> help flash write_bank
>> flash write_bank bank_id filename offset
>> Write binary data from file to flash bank, starting at specified
>> byte offset from the beginning of the bank."
>>
>> /Andreas
>>
>
>
> _______________________________________________
> Openocd-development mailing list
> Openocd-development@lists.berlios.de
> https://lists.berlios.de/mailman/listinfo/openocd-development
>
>
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
