Signed-off-by: Øyvind Harboe <[email protected]>
---
tcl/board/stm3220f_eval.cfg | 66 +++++++++++++++++++++++++++++++++++++++++++
1 files changed, 66 insertions(+), 0 deletions(-)
create mode 100644 tcl/board/stm3220f_eval.cfg
diff --git a/tcl/board/stm3220f_eval.cfg b/tcl/board/stm3220f_eval.cfg
new file mode 100644
index 0000000..3123f4b
--- /dev/null
+++ b/tcl/board/stm3220f_eval.cfg
@@ -0,0 +1,66 @@
+set CPUTAPID 0x4ba00477
+
+set _CHIPNAME stm32
+set _ENDIAN little
+
+# Work-area is a space in RAM used for flash programming
+# By default use 16kB
+if { [info exists WORKAREASIZE] } {
+ set _WORKAREASIZE $WORKAREASIZE
+} else {
+ set _WORKAREASIZE 0x4000
+}
+
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG =
1MHz
+adapter_khz 1000
+
+adapter_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#jtag scan chain
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ # See STM Document RM0008
+ # Section 26.6.3
+ set _CPUTAPID 0x3ba00477
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id
$_CPUTAPID
+
+if { [info exists BSTAPID ] } {
+ # FIXME this never gets used to override defaults...
+ set _BSTAPID $BSTAPID
+} else {
+ # See STM Document RM0008
+ # Section 29.6.2
+ # Low density devices, Rev A
+ set _BSTAPID1 0x06411041
+ # Medium density devices, Rev A
+ set _BSTAPID2 0x06410041
+ # Medium density devices, Rev B and Rev Z
+ set _BSTAPID3 0x16410041
+ # High density devices, Rev A
+ set _BSTAPID4 0x06414041
+ # Connectivity line devices, Rev A and Rev Z
+ set _BSTAPID5 0x06418041
+ # XL line devices, Rev A
+ set _BSTAPID6 0x06430041
+}
+jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+ -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
+ -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 \
+ -expected-id $_BSTAPID6
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME
+
+# FIX! flash programming fails with or without work area set.
+#$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size
$_WORKAREASIZE -work-area-backup 0
+
+# flash size will be probed
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME stm32x 0x08000000 0 0 0 $_TARGETNAME
+
+# if srst is not fitted use SYSRESETREQ to
+# perform a soft reset
+cortex_m3 reset_config sysresetreq
--
1.7.0.4
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
