Hi Ravi, Have you had a chance to review the log file yet? Was wondering if you had any suggestions, or if you need any additional data.
Thanks. Jim -----Original Message----- From: Bisirri, Christopher D (US) Sent: Friday, September 08, 2017 1:00 PM To: Ravi Sekhar Reddy Konda <[email protected]>; Carroll, James R (US) <[email protected]> Cc: [email protected] Subject: RE: EXTERNAL: Re: [users] Open-SAF 5.2 - question on TIPC usage/failovers Hi Ravi Sekhar, Attached is a smaller log file of just the standby controller's amfnd log. I previously sent multiple logs however they were too big and were quarantined. At time 20:31:01 just after the "Cold sync complete!" is when I issued the "opensafd stop" on the active controller. Thanks, Chris -----Original Message----- From: Bisirri, Christopher D (US) Sent: Tuesday, September 05, 2017 4:02 PM To: 'Ravi Sekhar Reddy Konda' <[email protected]>; Carroll, James R (US) <[email protected]> Cc: [email protected] Subject: RE: EXTERNAL: Re: [users] Open-SAF 5.2 - question on TIPC usage/failovers Hi Ravi Sekhar, Here are our logs which captures the issue Jim described earlier. This is a tar file that I renamed to ".allow" just in case your system strips attachments. You'll need to rename the file to logs.tar to view the logs. Just to give a little background. For this scenario we have 2 nodes defined as controllers, amcontroller1 (active) and amcontroller2 (standby). We performed an OpenSAF shut down on amcontroller1 expecting amcontroller2 to become the active controller. We shut down amcontroller1 by issuing the following command: "/etc/init.d/opensafd stop". Thanks for taking a look. -Chris -----Original Message----- From: Ravi Sekhar Reddy Konda [mailto:[email protected]] Sent: Monday, September 04, 2017 4:50 AM To: Carroll, James R (US) <[email protected]> Cc: [email protected] Subject: EXTERNAL: Re: [users] Open-SAF 5.2 - question on TIPC usage/failovers Hi Jim, I just tried the scenario that you explained with OpenSAF 5.2, I did not see any issue When you say reconfigure, I am expecting that you brought down the new Active and then reconfigured both the nodes OpenSAF to use TIPC. Can you share the amf logs when you face the issue, we can analyze the cause Regards, Ravi Sekhar ----- Original Message ----- From: [email protected] To: [email protected] Sent: Friday, September 1, 2017 9:48:55 PM GMT +05:30 Chennai, Kolkata, Mumbai, New Delhi Subject: Re: [users] Open-SAF 5.2 - question on TIPC usage/failovers Hi, We are running with OpenSAF 5.2. We have successfully run the following scenarios using TCP: 1) Two SC nodes, configured as active and Standby, use opensafd stop to perform graceful shutdown of active controller, Standby takes over as expected When we reconfigure OpenSAF to use TIPC, we are seeing problems with the Controller failovers. 1) Two SC nodes, use opensafd stop to perform graceful shutdown of active controller, Standby does not take over, eventually the immnd restarts, and we are left in a bad state that requires a node reboot. Is there any information available regarding this behavior, or are there other settings we need to adjust to configure TIPC properly? Additionally, we stepped back to OpenSAF 5.0, and confirmed this same identical behavior. When using TCP, the failover performs as expected. But when configured to use TIPC, this same erratic behavior occurs. Thanks. Jim ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! https://urldefense.proofpoint.com/v2/url?u=http-3A__sdm.link_slashdot&d=DwICAg&c=RoP1YumCXCgaWHvlZYR8PQcxBKCX5YTpkKY057SbK10&r=rFCQ76TW5HZUgA7b20ApVcXgXru6mvz4fvCm1_H6w1k&m=TFbplD6zN3y1rDAEkBcQvrLnBFPZ4_kUWO4dfPqxx-g&s=Lct2UGZVseNYSrM9wMoYVMOcxq4uO_Vu1cz0bhlCdrw&e= _______________________________________________ Opensaf-users mailing list [email protected] https://urldefense.proofpoint.com/v2/url?u=https-3A__lists.sourceforge.net_lists_listinfo_opensaf-2Dusers&d=DwICAg&c=RoP1YumCXCgaWHvlZYR8PQcxBKCX5YTpkKY057SbK10&r=rFCQ76TW5HZUgA7b20ApVcXgXru6mvz4fvCm1_H6w1k&m=TFbplD6zN3y1rDAEkBcQvrLnBFPZ4_kUWO4dfPqxx-g&s=-HzTg2WVlMVreo-sUSmYn-x8JTYTXeWhj4tktBHsVbg&e= ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Opensaf-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/opensaf-users ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Opensaf-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/opensaf-users
