Almost everything I am getting is from the Wiki. Sometimes the information is
conflicting and I have to figure out what one is fact and what one my have
applied to previous version. The one that's getting me now is the Region.ini
and the Default.xml On one page it says that the Default.xml should be in your
regions directory, and someplace else it says that with ver 0.6.6 it wasn't
created as part of the install and I need to make one manually and put it in
the Bin directory. As for the Regions.ini. I finally figured out that should
be for your default (Port 9000) region and all the others are regionname.xml
It also should be added to the configuration pages that you should use your
hosts internal IP address and not 0.0.0.0 as it states elsewhere, and that you
should use the IP address of your outside port on your modem and be sure to
open the appropriate router ports. Set up port forwarding and be sure to open
the ports on your firewall
Another tidbit should be to set up the IPTABLES correctly with the following
commands
LINUX:
* iptables -t nat -A OUTPUT --dst $EXTERNAL_IP -p tcp --dport 9000:9010
-j DNAT --to-destination $INTERNAL_IP
* iptables -t nat -A OUTPUT --dst $EXTERNAL_IP -p udp --dport 9000:9010
-j DNAT --to-destination $INTERNAL_IP
* service iptables restart
* iptables -t nat -L -n <---- this lits the rules for nat so you can
verify its set up right
Windows
iptables -t nat -A PREROUTING --dst 68.185.20.134 -p tcp --dport 9000:9010 -j
DNAT --to-destination 192.168.2.100
iptables -t nat -A PREROUTING --dst 68.185.20.134 -p udp --dport 9000:9010 -j
DNAT --to-destination 192.168.2.100
Put your proper IP's where indicated. also make sure you use the Exsternal IP
address when setting up your client if your useing a seperate machine, even if
its on the same network.
this is all in the WIKI but i think it couldn't hurt to be sure its all listed
under configuration. Will save people setting it up for the first time and
frustratingly having to dig through the documentation to find out why it isn't
working. All in all the documentation is complete, its just a little spread
out, and sometimes applies to different version. But I must applaud the people
working on it for the vast collection of information. If you spend a little
time looking you can find the answer to all your questions in there.
Rich
________________________________
From: Karen Palen <[email protected]>
To: [email protected]
Sent: Fri, October 9, 2009 2:27:16 AM
Subject: Re: [Opensim-users] Noobi question.
I hate to sound like a "broken record", but did you get all this into the wiki?
Hmm the only time I heard areal "broken record" that did that it was a 78 rpm
(!) vinyl record called "Christmas at the Front" recorded during WWi I - even
before MY time LOL
Karen
--- On Wed, 10/7/09, Richard Taft <[email protected]> wrote:
> From: Richard Taft <[email protected]>
> Subject: Re: [Opensim-users] Noobi question.
> To: [email protected]
> Date: Wednesday, October 7, 2009, 6:56 PM
> well
> I did it.... got logged in finally.... one
> pointer I can offer that did the final trick for
> me.... make sure that in the /Regions/Regions.ini file
> your internal address is set to 0.0.0.0 and make
> absolutely sure our external address is the IP address of
> your server INSIDE your firewall/router. I saw on one
> of the WIki pages that it should be set to your routers
> external address if you plan to access it from the
> outside. This is incorrect and you create a looping
> issue if you do. This will cause your viewer to freeze
> at region handshake.
>
> The other thing I noticed is that you Come up Ruthed.
> and no way to edit your appearance. what you
> have to do is go to body parts and create a shape, right
> click and edit...
> then go through each body item and move the slider
> slightly. and then save. you will have to do
> that with pants and shirt also. once your done you
> should be a real live Avitar. It seems strange, but
> there is items in the asset directory
>
> Ok Now I'm hooked, this is fun having a place all to
> myself. Still have some issues to work
> through... SLS isn't working, and I can't do
> video
>
> One thing I noticed.... what I wanted to do was creat
> seperate databases for Inventory/assets/estates/users....
> right now I have it all in one database an its
> working. so all my connect strings are
> correct... Opensim built the tables that it
> needed. so I shutdown Opensim Deleted ALL
> the tables... created a new database called opensiminv
> and granted all permissions from my existing opensim user...
> updated the inventory connect string so it pointed to this
> database. and restart
> Opensim.... it created all the tables in the
> "Default" database and creates a table called
> migrate in the inventory database, and then complains that
> it cant find an inventory table and halts. If I check
> the database, the table its looking for is in the default
> database, yet it seems to be looking in the inventory
> database. Have I found a bug? sould I attempt to
> move the inventory tables to the inventory
> database. Just as an extra, it does the same
> thing for the asset inventory and estate databases if I do
> the same procedure. What it seems to me is the routine
> that populates the tables in the database is only looking at
> one database.
>
> RichT
>
> From:
> Karen
> Palen <[email protected]>
> To:
> [email protected]
> Sent: Tue,
> October 6, 2009 11:18:54 PM
> Subject: Re:
> [Opensim-users] Noobi question.
>
>
> It is long, but I think you will find it quite well
> organized. The documentation is ambiguous in spots too, but
> Google helps. There are tutorials and "hint" files
> all over the web!
>
> My strategy has been to update the Wiki as I figure out
> something and get it working. That way I help everyone as
> well as having good (updated!) notes the next time I run
> into an issue.
>
> I am a Ubuntu user (only 8 mos on Linux), so I haven't
> done a lot of "distro surfing" yet. All the same
> you should find a lot of helpful info on the Wiki, and of
> course more detail and corrections are always welcome!
>
> Karen
>
> --- On Tue, 10/6/09, Richard Taft <[email protected]>
> wrote:
>
> > From: Richard Taft <[email protected]>
> > Subject: Re: [Opensim-users] Noobi question.
> >
> To: [email protected]
> > Date: Tuesday, October 6, 2009, 4:06 PM
> > Well
> > for a first timer its long... I decided to
> basically
> > start from scratch. I had a lot of fits and
> starts
> > getting Fedora to even compile opensim.
> Going to
> > try pulling down a fresh copy of Opensim and
> > recompile... Then only make small changes to the
> INI
> > and test as I go. I had to install Mono, Nant, and
> > LibGDIPlus by hand. As well as Mysql & the C+ and
> on and
> > on. I probably should have written it all down since
> it
> > might have helped someone else. There are
> several
> > Fedora guides out there, but none seem to be
> > "Complete" from raw install of fedora to
> > Installing Opensim.
> >
> > I think rather then add myself to a Grid I may
> want to
> > become my own grid. There are several friends that
> have
> > gotten tired of SL and its mess. I may make a
> retreat
> > that we
> > can all go to to build create and converse in
> peace.
> >
> > Anyone that may have some insight or gotcha warning
> please
> > feel free to chime in
> >
> > RichT
> >
> > From:
> > Robert Klein <[email protected]>
> > To:
> > [email protected]
> > Sent:
> > Tuesday, October 6, 2009 4:28:23 PM
> > Subject: Re:
> > [Opensim-users] Noobi question.
> >
> >
> >
> > LOL, it is very important to understand each section
> of the
> > OpenSim.ini file
> > and it is not as long as it looks. Okay it is as long
> as it
> >
> looks... :)
> >
> > -Robert
> >
> >
> > Richard Taft wrote:
> > >
> > > Well I answered my Own question.... Seems I
> went
> > a little Nuts on the
> > > OpenSim.ini Updates and shot myself in the
> foot.
> > The Include at the
> > > bottom was set to Grid.ini, which assumes that
> you
> > will be connecting to a
> > > remote asset and inventory server. I'll
> have
> > to do a bit more research
> > > into this configuration file and its
> parameters.
> > Its very easy to get
> > > lost and mess things up.
> > >
> > > RichT
> > >
> > >
> > >
> > >
> > > ________________________________
> > > From: Richard Taft <[email protected]>
> > > To: [email protected]
> > > Sent: Monday, October 5, 2009 11:38:16 PM
> > > Subject: [Opensim-users] Noobi question.
> > >
> > >
> > > I'm sure this has been asked a million
> > times.. But being new, I'll just
> > > have to ask it again. Running Opensim on a
> > Fedora 11 (No small
> > > undertaking) I had it running in stand alone
> mode, but
> > I'm attempting to
> > > activate grid mode. I didn't want to get it
> all
> > set up only to have to
> > > come back and reconfigure. I'm trying
> to
> > start it now and I am getting an
> > > exception "No server URI named in section
> > AssetService" I checked the
> > > AssetService section and I have asset_plugin set
> to
> > the MySQL plugin & the
> > > asset_source set to the connection string for my
> asset
> > database. I have
> > > confirmed that it is accessible and the password
> is
> > correct.
> > >
> > > I'm running the
> > current version of opensim, and I know the web
> site
> > > documentation doesn't exactly match, but
> I'm
> > at a loss to know what its
> > > looking for. Anyone have any Ideas?
> > >
> > > RichT
> > >
> > >
> > >
> > > _______________________________________________
> > > Opensim-users mailing list
> > > [email protected]
> > > https://lists.berlios.de/mailman/listinfo/opensim-users
> > >
> > >
> >
> > --
> > View this message in
> context: http://n2.nabble.com/Noobi-question-tp3772995p3777921.html
> > Sent from the opensim-users mailing list archive at Nabble.com.
> > _______________________________________________
> > Opensim-users mailing list
> > [email protected]
> > https://lists.berlios.de/mailman/listinfo/opensim-users
> >
> >
> >
> >
> >
> >
> > -----Inline Attachment Follows-----
> >
> > _______________________________________________
> > Opensim-users mailing list
> > [email protected]
> > https://lists.berlios.de/mailman/listinfo/opensim-users
> >
>
>
>
>
> _______________________________________________
> Opensim-users mailing list
> [email protected]
> https://lists.berlios.de/mailman/listinfo/opensim-users
>
>
>
>
> -----Inline Attachment Follows-----
>
> _______________________________________________
> Opensim-users mailing list
> [email protected]
> https://lists.berlios.de/mailman/listinfo/opensim-users
>
_______________________________________________
Opensim-users mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/opensim-users
_______________________________________________
Opensim-users mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/opensim-users
