Am 12.07.19 um 19:08 schrieb Knurpht-openSUSE:
> Op vrijdag 12 juli 2019 19:03:48 CEST schreef Bernd Nachtigall:
>> Am 12.07.19 um 17:53 schrieb Knurpht-openSUSE:
>>> Op vrijdag 12 juli 2019 16:35:33 CEST schreef Bernd Nachtigall:
>>>> After I install
>>>> openSUSE-Leap-15.1-ARM-XFCE-raspberrypi3.aarch64-2019.05.17-Snapshot1.18.
>>>> raw .xz to a RasPi I get a IP via DHCP during the first boot.
>>>>
>>>> Then I configure a fix IP via YaST. But this fix IP is configured as
>>>> secondary IP. Even if I remove the interface configuration and renew it
>>>> with the fix IP - after the YaST config runs throught, there are a
>>>> interface with a primary addess from DHCP and a additional secondary IP
>>>> from the fixed config.
>>>>
>>>> Where i can change this tricky behavior?
>>>>
>>>> Bernd
>>>
>>> Please show some confirmation:
>>> ip addr
>>
>> mon:/etc/sysconfig/network # ip a s
>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
>> group default qlen 1000
>> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>> inet 127.0.0.1/8 scope host lo
>> valid_lft forever preferred_lft forever
>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
>> state UP group default qlen 1000
>> link/ether b8:27:eb:8d:5b:c2 brd ff:ff:ff:ff:ff:ff
>> inet 192.168.250.181/25 brd 192.168.250.255 scope global
>> noprefixroute dynamic eth0
>> valid_lft 2816sec preferred_lft 2816sec
>> inet 192.168.250.185/25 brd 192.168.250.255 scope global secondary
>> noprefixroute eth0
>> valid_lft forever preferred_lft forever
>> inet6 fe80::c369:b4f2:7cdc:133c/64 scope link noprefixroute
>> valid_lft forever preferred_lft forever
>> 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
>> state DOWN group default qlen 1000
>> link/ether d2:f6:86:b8:bd:70 brd ff:ff:ff:ff:ff:ff
>>
>>
>> With this config it is not possible to connect to the I-Net. When I
>> delete .181 the connection is possible but after a while dhcp is rising
>> again.
>>
>> Bernd
> How do you configure it? Looks like you added a connection instead of editing
> the existing one.
>
No, I configure the existing interface.
From my POV it looks like an added IP for an existing interface. But
there is only one address configured for this interface. When look in YaST.
If I do an:
# ip addr del 192.168.250.181/25 dev eth0
The main addr of eth0 is removed, even as the secondary IP and the
address 192.168.250.185 is set as the main addr of eth0.
After a while somewhat reconfigure the network to the old state where
the DHCP addr is set :-\
Bernd
--
To unsubscribe, e-mail: opensuse-arm+unsubscr...@opensuse.org
To contact the owner, e-mail: opensuse-arm+ow...@opensuse.org
