Hi Nils,
i’m still not sure, that i know what you want.
You told about clients an server in different (v)lans. If this is really what
you have, then client and server are not connected. You have to realize a
connection.
But now I think you mean different subnets, right? If yes, then you also have
to realize that the client ant server can connect. I think you have to think
about the right routing.
As I remember, then you need to set the 060 and 066 option in the dhcp. And
please check: I think there was an special needed routing option to route the
pxe signal through different subnets.
Mit freundlichem Gruß
Julian Ohm
------------------------------------------
Ohm & Meyer Immobilien e. K.
Inh. Gabor Sarkany
Schiffbrücke 66
24939 Flensburg
Tel.: 0461 / 840 31 0
Fax.: 0461 / 840 31 11
HRA 2190 FL
Haftungsbeschränkungen/Disclaimer
Diese Nachricht enthält vertrauliche Informationen und ist ausschließlich
für den Adressaten bestimmt. Der Gebrauch durch Dritte ist verboten. Das
Unternehmen ist nicht verantwortlich für die ordnungsgemäße, vollständige
oder verzögerungsfreie Übertragung dieser Nachricht. Diese Hinweise gelten
auch für zukünftige Nachrichten.
This message may contain confidential information and is intended solely
for the use by the addressee. Use of this communication by others is
prohibited. The Company is neither liable for the proper and complete
transmission of the message nor for the delay in its receipt.
Von: Bott, Nils [mailto:nb...@doduco.net]
Gesendet: Donnerstag, 22. August 2013 07:21
An: openthinclient-user@lists.sourceforge.net
Betreff: Re: [openthinclient-user] DHCP Server 2003 and registration of new pxe
clients
Hi,
thanks for answer, but thats not the problem. I Know that i need a server
connection every time, if the client is in the manager evrything also works
fine.
I try to explain my problem better:
We got a DHCP 2003n Server with 5 Vlans.
We want our IT infrastructur convert from normal pc network to a thin client
network.
The OTSServer is in VLAN e.g 301.
The DHCP Server also in 301.
If i start a PC with PXE the first time in vlan 301, the boot fail of cousre.
In the managment console of OTCServer now appears the new Client and i can
configure it. Next boot and it works.
My problem is that when i start a other PC with PXE the first time, boot also
fails but nothing in the managment Console of OTCServer appears.
So what i have to configure on my DHCP Server or Core Switch or waht else that
the OTCServer discover every try of a PXE Boot in all Vlans. I don’t want to go
arround the company and write 500 MAC-Address down ;-).
Why my Client not known after the first boot by OTCServer. If i added a Client
manuel it boots, also in different Vlans. Hope you understand my problem.
Nils
Von: Julian Ohm [mailto:j...@ohm-meyer.de]
Gesendet: Mittwoch, 21. August 2013 19:44
An: openthinclient-user@lists.sourceforge.net
Betreff: Re: [openthinclient-user] DHCP Server 2003 and registration of new pxe
clients
Hi Nils,
I'm not sure that i really understand what you want.
The Way OTC works (as far as i understood that).
With the first boot the client becomes known by the OTC Server. Heer you decide
whether the client should use OTC or not. If yes, then you have to configure
the client weithin the Manager. After that the client becomes the bootfile, his
operating System, configuration, etc from the otc Server.
Thats why the client need the connection to the server everytime it boots. Even
if you use the install on hard disk as far as i know. Then the Operation System
is installed, but the configuration still comes from the server.
Excuse me for my Bad english.
Julian
Von meinem iPad gesendet
Am 21.08.2013 um 19:10 schrieb "Bott, Nils" <nb...@doduco.net>:
Hello,
i installed the OTC-Server. If i added manuel a thin client everything works
fine, even in different vlans.
Now my Problem:
If i start a pxe client in the same subnet as the OTC first time, the client
appear in the pxe-client card of the managment console, but if i start a pxe
client in an other vlan nothing appear in the pxe-client card. So how i have to
configere my dhcp server that every pxe start will registerd by the OTCServer ?
My current configuration at the DHCP 2003 Windows Server:
043 Vendor Specific Info, 01 04 00 00 00 00
060 Client Identefier, PXEClient
066, Boot Server Host Name, my OTC-Server IP
067 Bootfile name pxelinux.0
So what i have to fix that every try of pxe boot, special in different vlan as
the OTC-Server, so that every client after the first boot-try appear in the
managment console of the OTC-Server.
Sorry for my bad english, i hope you can understand my problem and it sounds
friendly.
Many thanks for your support in advance
With best regards
Nils
------------------------------------------------------------------------------
Introducing Performance Central, a new site from SourceForge and
AppDynamics. Performance Central is your source for news, insights,
analysis and resources for efficient Application Performance Management.
Visit us today!
http://pubads.g.doubleclick.net/gampad/clk?id=48897511
<http://pubads.g.doubleclick.net/gampad/clk?id=48897511&iu=/4140/ostg.clktrk>
&iu=/4140/ostg.clktrk
_______________________________________________
The Open Source Thin Client Solution http://openthinclient.org
openthinclient-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/openthinclient-user
--
Diese E-Mail wurde auf Viren und gefährliche Anhänge
durch <http://www.mailscanner.info/> MailScanner untersucht und ist
wahrscheinlich virenfrei.
------------------------------------------------------------------------------
Introducing Performance Central, a new site from SourceForge and
AppDynamics. Performance Central is your source for news, insights,
analysis and resources for efficient Application Performance Management.
Visit us today!
http://pubads.g.doubleclick.net/gampad/clk?id=48897511&iu=/4140/ostg.clktrk
_______________________________________________
The Open Source Thin Client Solution http://openthinclient.org
openthinclient-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/openthinclient-user