hi mirko, florian thanks for the info. i run 'make distclean' and recompile. will test the rootfs later.
http://www.qi-hardware.com 在 2009-Jul-27 7:44 PM，"Mirko Vogt" <li...@nanl.de> 说： "Please be patient, while OpenWrt loads ..." is the last message shown by the kernel. That indicates, the userspace isn't working / entered at this state, but mounted successfully. Mostly that is one of the following cases: - wrong binary format - /etc/preinit isn't executed by default (the bootloader _must not_ override the init= argument to the kernel) mirko (the other one) On Mon, 2009-07-27 at 11:12 +0800, Xiangfu Liu wrote: > Hi there > I work on a jz4740 cpu device. t... > plain text document attachment (error.message.txt) > NAND Secondary Program Loader > > > U-Boot 2009.06-dirty (Jul 26 2009 - 16:40:30) > > Board: Qi LB60 (Ingenic XBurst Jz4740 SoC, Speed 252 MHz) > DRAM: 32 MB > NAND: 2048 MiB > Linux version 2.6.28.10-ge8db213 (xian...@openmobilefree.net) (gcc version 4.1.9 > CPU revision is: 0ad0024f (Ingenic JZRISC) > CPU clock: 252MHz, System clock: 84MHz, Peripheral clock: 84MHz, Memory clock: z > Qi Hardware JZ4740 QI_LB60 setup > Determined physical RAM map: > memory: 04000000 @ 00000000 (usable) > User-defined physical RAM map: > memory: 02000000 @ 00000000 (usable) > Zone PFN ranges: > Normal 0x00000000 -> 0x00002000 > Movable zone start PFN for each node > early_node_map[1] active PFN ranges > 0: 0x00000000 -> 0x00002000 > Built 1 zonelists in Zone order, mobility grouping off. Total pages: 8128 > Kernel command line: mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mm2 > Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. > Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes > PID hash table entries: 128 (order: 7, 512 bytes) > ------------[ cut here ]------------ > WARNING: at kernel/time/clockevents.c:175 () > Modules linked in: > Call Trace:[<80024890>] 0x80024890 > [<80024890>] 0x80024890 > [<80041188>] 0x80041188 > [<803df198>] 0x803df198 > [<80041810>] 0x80041810 > [<803debd8>] 0x803debd8 > [<803f2e14>] 0x803f2e14 > [<803f12c8>] 0x803f12c8 > [<803ded54>] 0x803ded54 > [<80067640>] 0x80067640 > [<80069f28>] 0x80069f28 > [<80068764>] 0x80068764 > [<803d95d8>] 0x803d95d8 > [<803d5938>] 0x803d5938 > [<803d50d8>] 0x803d50d8 > > ---[ end trace 4eaa2a86a8e2da22 ]--- > Console: colour dummy device 80x25 > console [ttyS0] enabled > Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) > Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) > Memory: 28252k/32768k available (3186k kernel code, 4516k reserved, 671k data, ) > Calibrating delay loop... 250.67 BogoMIPS (lpj=1253376) > Mount-cache hash table entries: 512 > net_namespace: 288 bytes > NET: Registered protocol family 16 > SCSI subsystem initialized > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 1024 (order: 1, 8192 bytes) > TCP bind hash table entries: 1024 (order: 0, 4096 bytes) > TCP: Hash tables configured (established 1024 bind 1024) > TCP reno registered > NET: Registered protocol family 1 > Total 4MB memory at 0x1400000 was reserved for IPU > squashfs: version 3.0 (2006/03/15) Phillip Lougher > Registering mini_fo version $Id$ > JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. > msgmni has been set to 55 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered (default) > io scheduler deadline registered > io scheduler cfq registered > jzlcd use 1 framebuffer: > jzlcd fb[0] phys addr =0x01100000 > LCDC: PixClock:25200000 LcdClock:63000000 > Console: switching to colour frame buffer device 40x30 > fb0: jz-lcd frame buffer device, using 512K of video memory > JzSOC: char device family. > JZ UDC hotplug driver registered > Serial: 8250/16550 driver2 ports, IRQ sharing disabled > UDC starting pnp monitor thread > �Wߖ��|[�ޙM�ܝ�ttyS0 at MMIO 0x0 (irq = 9) is a 16550A > serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A > brd: module loaded > loop: module loaded > Driver 'sd' needs updating - please use bus_type methods > Nand DMA request channel 0. > NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit2 > Nand using two-plane mode, and resized to writesize:8192 oobsize:256 blocksize: > Scanning device for bad blocks > Bad eraseblock 16 at 0x00087f000 > Bad eraseblock 17 at 0x0008ff000 > Bad eraseblock 18 at 0x00097f000 > Bad eraseblock 19 at 0x0009ff000 > Bad eraseblock 20 at 0x000a7f000 > Bad eraseblock 21 at 0x000aff000 > Creating 6 MTD partitions on "NAND 2GiB 3,3V 8-bit": > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x00000000-0x00400000 : "NAND BOOT partition" > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x00400000-0x00800000 : "NAND KERNEL partition" > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x00800000-0x20000000 : "NAND ROOTFS partition" > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x20000000-0x40000000 : "NAND DATA1 partition" > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x40000000-0x60000000 : "NAND DATA2 partition" > Creating 1 MTD partitions on "NAND 2GiB 3,3V 8-bit": > 0x60000000-0x80000000 : "NAND VFAT partition" > JzSOC Watchdog Timer: timer margin 60 sec > JZ SD/MMC card driver registered > JzSOC On-Chip I2S controller registered (DAC: DMA(play):2/IRQ34, > ADC: DMA(record):1/IRQ33) > JZ I2S OSS audio driver initialized > TCP cubic registered > NET: Registered protocol family 17 > mmc0: new high speed SD card at address b368 > mmcblk0: mmc0:b368 NCard 1.85 GiB > mmcblk0: p1 p2 p3 p4 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > Waiting 2sec before mounting root device... > EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended > VFS: Mounted root (ext2 filesystem). > Freeing unused kernel memory: 172k freed > Please be patient, while OpenWrt loads ... > > > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/openwrt-devel _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
