anyone could tell me how to resolve the problem, I want NOT to change my
kamikaze version.
I used the kamikaze r19358.
2010/3/10 OpenWrt <openwrt-devel@lists.openwrt.org>
> #6812: kamikaze trunk can't start RB433AH
>
> --------------------------------+-------------------------------------------
> Reporter: jete...@… | Owner: developers
> Type: defect | Status: closed
> Priority: high | Milestone: Kamikaze
> Component: base system | Version: Kamikaze trunk
> Resolution: worksforme | Keywords:
>
> --------------------------------+-------------------------------------------
> Changes (by juhosg):
>
> * status: new => closed
> * resolution: => worksforme
>
>
> Comment:
>
> Booting of the intramfs kernel:
> {{{
> RouterBOOT booter 2.15
>
> RouterBoard 433AH
>
> Authorization: Passed
> CPU frequency: 680 MHz
> Memory size: 128 MB
>
> Press any key within 4 seconds to enter setup.
>
> RouterBOOT-2.15
> What do you want to configure?
> d - boot delay
> k - boot key
> s - serial console
> o - boot device
> u - cpu mode
> f - cpu frequency
> r - reset booter configuration
> e - format nand
> g - upgrade firmware
> i - board info
> p - boot protocol
> x - exit setup
> your choice: o - boot device
>
> Select boot device:
> * e - boot over Ethernet
> n - boot from NAND, if fail then Ethernet
> 1 - boot Ethernet once, then NAND
> o - boot from NAND only
> b - boot chosen device
> your choice: b - boot chosen device
> trying dhcp protocol... OK
> resolved mac address 00:1F:D0:3F:39:3C
> transfer started .............................. transfer ok, time=1.51s
> setting up elf image... OK
> jumping to kernel code
> Linux version 2.6.32.9 (juh...@idared) (gcc version 4.3.3 (GCC) ) #12 Tue
> Mar 9 21:36:31 CET 2010
> bootconsole [early0] enabled
> CPU revision is: 00019374 (MIPS 24Kc)
> Atheros AR7161 rev 2, CPU:680.000 MHz, AHB:170.000 MHz, DDR:340.000 MHz
> Determined physical RAM map:
> memory: 08000000 @ 00000000 (usable)
> User-defined physical RAM map:
> memory: 08000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 0x00000000 -> 0x00008000
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0x00000000 -> 0x00008000
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
> Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd
> console=ttyS0,115200 console=ttyS0,115200 gpio=4031 HZ=3
> 40000000 mem=128M kmac=00:0C:42:2D:B6:E4 board=433 boot=0
> PID hash table entries: 512 (order: -1, 2048 bytes)
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
> Writing ErrCtl register=00012000
> Readback ErrCtl register=00012000
> Memory: 125396k/131072k available (2027k kernel code, 5508k reserved, 523k
> data, 1336k init, 0k highmem)
> SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Hierarchical RCU implementation.
> NR_IRQS:56
> Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
> Mount-cache hash table entries: 512
> NET: Registered protocol family 16
> MIPS: machine is MikroTik RouterBOARD 433/AH
> registering PCI controller with io_map_base unset
> bio: create slab <bio-0> at 0
> pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:00.0: PME# disabled
> Switching to clocksource MIPS
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> NET: Registered protocol family 1
> squashfs: version 4.0 (2009/01/31) Phillip Lougher
> Registering mini_fo version $Id$
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> yaffs Mar 9 2010 09:16:07 Installing.
> msgmni has been set to 245
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
> serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
> console [ttyS0] enabled, bootconsole disabled
> console [ttyS0] enabled, bootconsole disabled
> NAND flash driver for RouterBoard 4xx series version 0.1.10
> NAND SPI clock 28333 kHz (AHB 170000 kHz / 6)
> FLASH SPI clock 28333 kHz (AHB 170000 kHz / 6)
> NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V
> 8-bit)
> Scanning device for bad blocks
> Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
> 0x000000000000-0x000000040000 : "booter"
> 0x000000040000-0x000000400000 : "kernel"
> 0x000000400000-0x000004000000 : "rootfs"
> mtd: partition "rootfs" set to be root filesystem
> split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
> Atheros AR71xx SPI Controller driver version 0.2.4
> ag71xx_mdio: probed
> eth0: Atheros AG71xx at 0xba000000, irq 5
> eth1: Atheros AG71xx at 0xb9000000, irq 4
> Atheros AR71xx hardware watchdog driver version 0.1.0
> TCP westwood registered
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
> All bugs added by David S. Miller <da...@redhat.com>
> Freeing unused kernel memory: 1336k freed
> gpio-buttons driver version 0.1.2
> input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
> Button Hotplug driver version 0.3.1
> - preinit -
> Registered led device: rb4xx:yellow:user
> Press f<ENTER> to enter failsafe mode
> - regular preinit -
>
> Please press Enter to activate this console. device eth0 entered
> promiscuous mode
> eth1: link up (100Mbps/Full duplex)
> Generic kernel compatibility enabled based on linux-next next-20100113
> cfg80211: Calling CRDA to update world regulatory domain
> PPP generic driver version 2.4.2
> ip_tables: (C) 2000-2006 Netfilter Core Team
> NET: Registered protocol family 24
> nf_conntrack version 0.5.0 (1982 buckets, 7928 max)
> eth0: link up (100Mbps/Full duplex)
> br-lan: port 1(eth0) entering forwarding state
>
>
>
> BusyBox v1.15.3 (2010-03-09 20:58:41 CET) built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> _______ ________ __
> | |.-----.-----.-----.| | | |.----.| |_
> | - || _ | -__| || | | || _|| _|
> |_______|| __|_____|__|__||________||__| |____|
> |__| W I R E L E S S F R E E D O M
> KAMIKAZE (bleeding edge, r20099) ------------------
> * 10 oz Vodka Shake well with ice and strain
> * 10 oz Triple sec mixture into 10 shot glasses.
> * 10 oz lime juice Salute!
> ---------------------------------------------------
> r...@openwrt:/#
> }}}
>
> Installing OpenWrt:
>
> {{{
> r...@openwrt:/# wget2nand ftp://192.168.1.254:2121/openwrt
> udhcpc (v1.15.3) started
> Sending discover...
> Sending select for 192.168.1.7...
> Lease of 192.168.1.7 obtained, lease time 36000
> udhcpc: ifconfig br-lan 192.168.1.7 netmask 255.255.255.0 broadcast +
> Connecting to 192.168.1.254:2121 (192.168.1.254:2121)
> kernel 100% |*******************************| 2735k
> 00:00:00 ETA
> Connecting to 192.168.1.254:2121 (192.168.1.254:2121)
> rootfs.tgz 100% |*******************************| 1710k
> 00:00:00 ETA
> Erasing filesystem...
> Mounting /dev/mtdblock2 as new root and /dev/mtdblock1 as kernel partition
> yaffs: dev is 32505857 name is "mtdblock1"
> yaffs: passed flags ""
> yaffs: Attempting MTD mount on 31.1, "mtdblock1"
> yaffs: auto selecting yaffs1
> yaffs_read_super: isCheckpointed 0
> yaffs: dev is 32505858 name is "mtdblock2"
> yaffs: passed flags ""
> yaffs: Attempting MTD mount on 31.2, "mtdblock2"
> yaffs: auto selecting yaffs1
> yaffs_read_super: isCheckpointed 0
> Copying kernel...
> Preparing filesystem...
> ./
> ./sys/
> ./mnt/
> ./proc/
> ./etc/
> [...]
> ./bin/pwd
> ./bin/ps
> ./bin/egrep
> ./bin/mktemp
> save exit: isCheckpointed 0
> save exit: isCheckpointed 0
> Cleaning up...
> save exit: isCheckpointed 0
> save exit: isCheckpointed 0
> Image written, you can now reboot. Remember to change the boot source to
> Boot from Nand
> r...@openwrt:/#
> }}}
>
> Reboot:
> {{{
> r...@openwrt:/# reboot
> r...@openwrt:/# br-lan: port 2(eth1) entering disabled state
> device eth1 left promiscuous mode
> br-lan: port 2(eth1) entering disabled state
> device eth0 left promiscuous mode
> br-lan: port 1(eth0) entering disabled state
> eth1: link down
> Restarting system.
>
>
> RouterBOOT booter 2.15
>
> RouterBoard 433AH
>
> Authorization: Passed
> CPU frequency: 680 MHz
> Memory size: 128 MB
>
> Press any key within 4 seconds to enter setup....
> Please, check ethernet cable...
> Ethernet link absent...
> trying dhcp protocol............................ failed
> kernel loading failed
>
>
> RouterBOOT booter 2.15
>
> RouterBoard 433AH
>
> Authorization: Passed
> CPU frequency: 680 MHz
> Memory size: 128 MB
>
> Press any key within 4 seconds to enter setup
>
> RouterBOOT-2.15
> What do you want to configure?
> d - boot delay
> k - boot key
> s - serial console
> o - boot device
> u - cpu mode
> f - cpu frequency
> r - reset booter configuration
> e - format nand
> g - upgrade firmware
> i - board info
> p - boot protocol
> x - exit setup
> your choice: o - boot device
>
> Select boot device:
> * e - boot over Ethernet
> n - boot from NAND, if fail then Ethernet
> 1 - boot Ethernet once, then NAND
> o - boot from NAND only
> b - boot chosen device
> your choice: n - boot from NAND, if fail then Ethernet
>
> RouterBOOT-2.15
> What do you want to configure?
> d - boot delay
> k - boot key
> s - serial console
> o - boot device
> u - cpu mode
> f - cpu frequency
> r - reset booter configuration
> e - format nand
> g - upgrade firmware
> i - board info
> p - boot protocol
> x - exit setup
> your choice: x - exit setup
>
>
> writing settings to flash... OK
>
>
> RouterBOOT booter 2.15
>
> RouterBoard 433AH
>
> Authorization: Passed
> CPU frequency: 680 MHz
> Memory size: 128 MB
>
> Press any key within 4 seconds to enter setup....
> loading kernel from nand... OK
> setting up elf image... OK
> jumping to kernel code
> Linux version 2.6.32.9 (juh...@idared) (gcc version 4.3.3 (GCC) ) #14 Wed
> Mar 10 08:33:17 CET 2010
> bootconsole [early0] enabled
> CPU revision is: 00019374 (MIPS 24Kc)
> Atheros AR7161 rev 2, CPU:680.000 MHz, AHB:170.000 MHz, DDR:340.000 MHz
> Determined physical RAM map:
> memory: 08000000 @ 00000000 (usable)
> User-defined physical RAM map:
> memory: 08000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 0x00000000 -> 0x00008000
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0x00000000 -> 0x00008000
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
> Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd
> console=ttyS0,115200 console=ttyS0,115200 gpio=4031 HZ=3
> 40000000 mem=128M kmac=00:0C:42:2D:B6:E4 board=433 boot=0
> PID hash table entries: 512 (order: -1, 2048 bytes)
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
> Writing ErrCtl register=00012000
> Readback ErrCtl register=00012000
> Memory: 126592k/131072k available (2000k kernel code, 4292k reserved, 518k
> data, 152k init, 0k highmem)
> SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Hierarchical RCU implementation.
> NR_IRQS:56
> Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
> Mount-cache hash table entries: 512
> NET: Registered protocol family 16
> MIPS: machine is MikroTik RouterBOARD 433/AH
> registering PCI controller with io_map_base unset
> bio: create slab <bio-0> at 0
> pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:00.0: PME# disabled
> Switching to clocksource MIPS
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> NET: Registered protocol family 1
> squashfs: version 4.0 (2009/01/31) Phillip Lougher
> Registering mini_fo version $Id$
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> yaffs Mar 9 2010 09:16:07 Installing.
> msgmni has been set to 247
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
> serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
> console [ttyS0] enabled, bootconsole disabled
> console [ttyS0] enabled, bootconsole disabled
> NAND flash driver for RouterBoard 4xx series version 0.1.10
> NAND SPI clock 28333 kHz (AHB 170000 kHz / 6)
> FLASH SPI clock 28333 kHz (AHB 170000 kHz / 6)
> NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V
> 8-bit)
> Scanning device for bad blocks
> Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
> 0x000000000000-0x000000040000 : "booter"
> 0x000000040000-0x000000400000 : "kernel"
> 0x000000400000-0x000004000000 : "rootfs"
> mtd: partition "rootfs" set to be root filesystem
> split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
> Atheros AR71xx SPI Controller driver version 0.2.4
> ag71xx_mdio: probed
> eth0: Atheros AG71xx at 0xba000000, irq 5
> eth1: Atheros AG71xx at 0xb9000000, irq 4
> Atheros AR71xx hardware watchdog driver version 0.1.0
> TCP westwood registered
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
> All bugs added by David S. Miller <da...@redhat.com>
> yaffs: dev is 32505858 name is "mtdblock2"
> yaffs: passed flags ""
> yaffs: Attempting MTD mount on 31.2, "mtdblock2"
> yaffs_read_super: isCheckpointed 0
> VFS: Mounted root (yaffs filesystem) readonly on device 31:2.
> Freeing unused kernel memory: 152k freed
> Please be patient, while OpenWrt loads ...
> gpio-buttons driver version 0.1.2
> input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
> Button Hotplug driver version 0.3.1
> - preinit -
> Registered led device: rb4xx:yellow:user
> Press f<ENTER> to enter failsafe mode
> - regular preinit -
> - init -
>
> Please press Enter to activate this console. device eth0 entered
> promiscuous mode
> eth1: link up (100Mbps/Full duplex)
> Generic kernel compatibility enabled based on linux-next next-20100113
> cfg80211: Calling CRDA to update world regulatory domain
> PPP generic driver version 2.4.2
> ip_tables: (C) 2000-2006 Netfilter Core Team
> NET: Registered protocol family 24
> nf_conntrack version 0.5.0 (1983 buckets, 7932 max)
> Driver for 1-wire Dallas network protocol.
>
>
>
> BusyBox v1.15.3 (2010-03-09 20:58:41 CET) built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> _______ ________ __
> | |.-----.-----.-----.| | | |.----.| |_
> | - || _ | -__| || | | || _|| _|
> |_______|| __|_____|__|__||________||__| |____|
> |__| W I R E L E S S F R E E D O M
> KAMIKAZE (bleeding edge, r20099) ------------------
> * 10 oz Vodka Shake well with ice and strain
> * 10 oz Triple sec mixture into 10 shot glasses.
> * 10 oz lime juice Salute!
> ---------------------------------------------------
> r...@openwrt:/#
> }}}
>
> --
> Ticket URL: <https://dev.openwrt.org/ticket/6812#comment:4>
> OpenWrt <http://openwrt.org>
> Opensource Wireless Router Technology
>
--
Yongheng Qi
Mobile: +86 1390 119 7481
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
