On 13-03-19 11:27 PM, Rafał Miłecki wrote:
> 2013/3/20 Owen Kirby <o...@exegin.com>:
>> I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing
>> into the box did I find it
>> was one of the v3 boards, with poor OpenWRT support. This patch should add
>> the board detection and
>> LED/button control to the broadcom-diag module, and should generate a
>> netgear .chk image that the
>> bootloader and stock firmware will accept.
>>
>> The changes to the broadcom-diag module are more than a few lines because
>> the WNDR3700v3 is driving
>> its LEDs through an HC164 8-bit shift register.
> Wow, thanks for looking at this! Could you provide us booting log, please?
>
Sure, here's the factory boot log
Decompressing..........done
Decompressing..........done
CFE for WNDR3700v3 version: v1.0.6
Build Date: Wed May 18 17:25:10 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 2010.09.30.0
CPU type 0x19740: 480MHz
Tot mem: 65536 KBytes
Device eth0: hwaddr 2C-B0-5D-44-1B-54, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Linux version 2.6.22 (peter@localhost.localdomain) (gcc version 4.2.3) #1 Wed
Sep 14 10:38:51 CST 2011
CPU revision is: 00019740
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Determined physical RAM map:
memory: 03fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 16383
HighMem 16383 -> 16383
early_node_map[1] active PFN ranges
0: 0 -> 16383
Built 1 zonelists. Total pages: 16383
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60016k/65532k available (3086k kernel code, 5460k reserved, 593k data,
204k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: no core
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1646
Creating 15 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x00740000 : "linux"
0x0019b96c-0x00740000 : "rootfs"
0x00740000-0x00750000 : "ML1"
0x00750000-0x00760000 : "ML2"
0x00760000-0x00770000 : "ML3"
0x00770000-0x00780000 : "ML4"
0x00780000-0x00790000 : "ML5"
0x00790000-0x007a0000 : "ML6"
0x007a0000-0x007b0000 : "ML7"
0x007b0000-0x007c0000 : "T_Meter1"
0x007c0000-0x007d0000 : "T_Meter2"
0x007d0000-0x007e0000 : "POT"
0x007e0000-0x007f0000 : "board_data"
0x007f0000-0x00800000 : "nvram"
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
All bugs added by David S. Miller <da...@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
Warning: unable to open an initial console.
Failed to execute /init
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
Reading board data...
WSC UUID: 0xdd7f9f4f97939e4b3d6fd1cc93a2afe3
NTP synchronized date/time: 00-00-00
MAC address of 1st STA connected: 00-25-BC-79-16-1F
invalid RF magic!
No RF parameters! Use default.
Initialise conn table 2048 entries
Hit enter to continue...wlconf: PHYTYPE: 4
wlconf: PHYTYPE: 7
wlconf: PHYTYPE: 4
wlconf: PHYTYPE: 7
killall: upnp: no process killed
Reaped 1916
UPnP daemon is ready to run
killall: wps_monitor: no process killed
killall: wps_ap: no process killed
killall: wps_enr: no process killed
### wps_wfi_init(): <wl0_wfi_enable=(null)><wl1_wfi_enable=(null)>WFI is not
enabled ###
Reading board data...
WSC UUID: 0xdd7f9f4f97939e4b3d6fd1cc93a2afe3
info, udhcp server (v0.9.8) started
error, unable to parse 'option wins '
error, unable to parse 'option domain '
POT integrity check OK.
Info: No FWPT default policies.
/tmp/samba/private/smb.conf: no files!
killall: bftpd: no process killed
--> start minidlna.exe.
httpd: socket bound in 0.0.0.0:80.
Scanning /tmp/shares finished (0 files)!
IOCTL_AG_REGION_SET: English
Start DHCP client daemon
info, udhcp client (v0.9.8) started
eth0: No such process
route: ioctl 0x890c failed: No such process
killall: dhcp6c: no process killed
killall: IPv6-relay: no process killed
killall: pppdv6: no process killed
killall: rtsol: no process killed
killall: dhcp6s: no process killed
killall: radvd: no process killed
route: ioctl 0x890c failed: No such process
killall: dhcp6s: no process killed
killall: radvd: no process killed
Hit enter to continue...
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
