On 19/10/2018 13:17, Ram Chandra Jangir wrote:
We have IPQ8064 AP161 board which has three GMAC's
* RGMII x2
* SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.
Signed-off-by: xiaofeis <xiaof...@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjan...@codeaurora.org>
---
.../linux/generic/files/drivers/net/phy/ar8216.c | 15 +++++++-
.../linux/generic/files/drivers/net/phy/ar8216.h | 4 ++
.../linux/generic/files/drivers/net/phy/ar8327.c | 43 ++++++++++++++++++++++
.../linux/generic/files/drivers/net/phy/ar8327.h | 7 ++++
4 files changed, 68 insertions(+), 1 deletion(-)
diff --git a/target/linux/generic/files/drivers/net/phy/ar8216.c
b/target/linux/generic/files/drivers/net/phy/ar8216.c
index 7512ee1..4c9c9ae 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8216.c
+++ b/target/linux/generic/files/drivers/net/phy/ar8216.c
@@ -295,6 +295,17 @@ ar8xxx_rmw(struct ar8xxx_priv *priv, int reg, u32 mask,
u32 val)
return ret;
}
+void
+ar8xxx_phy_dbg_read(struct ar8xxx_priv *priv, int phy_addr,
+ u16 dbg_addr, u16 *dbg_data)
+{
+ struct mii_bus *bus = priv->mii_bus;
+
+ mutex_lock(&bus->mdio_lock);
+ bus->write(bus, phy_addr, MII_ATH_DBG_ADDR, dbg_addr);
+ *dbg_data = bus->read(bus, phy_addr, MII_ATH_DBG_DATA);
+ mutex_unlock(&bus->mdio_lock);
+}
void
ar8xxx_phy_dbg_write(struct ar8xxx_priv *priv, int phy_addr,
@@ -2167,7 +2178,7 @@ ar8xxx_phy_probe(struct phy_device *phydev)
int ret;
/* skip PHYs at unused adresses */
- if (phydev->mdio.addr != 0 && phydev->mdio.addr != 4)
+ if (phydev->mdio.addr != 0 && phydev->mdio.addr != 3 &&
phydev->mdio.addr != 4)
return -ENODEV;
if (!ar8xxx_is_possible(phydev->mdio.bus))
@@ -2226,6 +2237,8 @@ found:
phydev->supported |= SUPPORTED_1000baseT_Full;
phydev->advertising |= ADVERTISED_1000baseT_Full;
}
+ if (priv->chip->phy_rgmii_set)
+ priv->chip->phy_rgmii_set(priv, phydev);
}
phydev->priv = priv;
diff --git a/target/linux/generic/files/drivers/net/phy/ar8216.h
b/target/linux/generic/files/drivers/net/phy/ar8216.h
index ba0e0dd..ecb91f4 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8216.h
+++ b/target/linux/generic/files/drivers/net/phy/ar8216.h
@@ -412,6 +412,7 @@ struct ar8xxx_chip {
void (*get_arl_entry)(struct ar8xxx_priv *priv, struct arl_entry *a,
u32 *status, enum arl_op op);
int (*sw_hw_apply)(struct switch_dev *dev);
+ void (*phy_rgmii_set)(struct ar8xxx_priv *priv, struct phy_device
*phydev);
const struct ar8xxx_mib_desc *mib_decs;
unsigned num_mibs;
@@ -477,6 +478,9 @@ u32
ar8xxx_rmw(struct ar8xxx_priv *priv, int reg, u32 mask, u32 val);
void
+ar8xxx_phy_dbg_read(struct ar8xxx_priv *priv, int phy_addr,
+ u16 dbg_addr, u16 *dbg_data);
+void
ar8xxx_phy_dbg_write(struct ar8xxx_priv *priv, int phy_addr,
u16 dbg_addr, u16 dbg_data);
void
diff --git a/target/linux/generic/files/drivers/net/phy/ar8327.c
b/target/linux/generic/files/drivers/net/phy/ar8327.c
index 74f0a08..6fe7bb1 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8327.c
+++ b/target/linux/generic/files/drivers/net/phy/ar8327.c
@@ -128,6 +128,48 @@ ar8327_get_pad_cfg(struct ar8327_pad_cfg *cfg)
}
static void
+ar8327_phy_rgmii_set(struct ar8xxx_priv *priv, struct phy_device *phydev)
+{
+ u32 rgmii = 0, tx_delay = 0, rx_delay = 0;
+ u16 phy_val = 0;
+ int phyaddr = phydev->mdio.addr;
+ struct device_node *np = phydev->mdio.dev.of_node;
+
+ if (!np)
+ return;
+
+ if (!of_property_read_u32(np, "phy_rgmii_en", &rgmii)) {
+ if (!rgmii)
+ return;
+ ar8xxx_phy_dbg_read(priv, phyaddr,
+ AR8327_PHY_MODE_SEL, &phy_val);
+ phy_val |= AR8327_PHY_MODE_SEL_RGMII;
+ ar8xxx_phy_dbg_write(priv, phyaddr,
+ AR8327_PHY_MODE_SEL, phy_val);
+
+ /* set rgmii tx clock delay if needed */
+ if (!of_property_read_u32(np, "txclk_delay_en", &tx_delay)
property names need to be prefixed by qca, and use dashes and not
underscores. please make these properties boolean and return directly
when they are not present, rather than indenting the code block
John
+ && tx_delay == 1) {
+ ar8xxx_phy_dbg_read(priv, phyaddr,
+ AR8327_PHY_SYS_CTRL, &phy_val);
+ phy_val |= AR8327_PHY_SYS_CTRL_RGMII_TX_DELAY;
+ ar8xxx_phy_dbg_write(priv, phyaddr,
+ AR8327_PHY_SYS_CTRL, phy_val);
+ }
+
+ /* set rgmii rx clock delay if needed */
+ if (!of_property_read_u32(np, "rxclk_delay_en", &rx_delay)
+ && rx_delay == 1) {
+ ar8xxx_phy_dbg_read(priv, phyaddr,
+ AR8327_PHY_TEST_CTRL, &phy_val);
+ phy_val |= AR8327_PHY_TEST_CTRL_RGMII_RX_DELAY;
+ ar8xxx_phy_dbg_write(priv, phyaddr,
+ AR8327_PHY_TEST_CTRL, phy_val);
+ }
+ }
+}
+
+static void
ar8327_phy_fixup(struct ar8xxx_priv *priv, int phy)
{
switch (priv->chip_rev) {
@@ -1496,6 +1538,7 @@ const struct ar8xxx_chip ar8337_chip = {
.set_mirror_regs = ar8327_set_mirror_regs,
.get_arl_entry = ar8327_get_arl_entry,
.sw_hw_apply = ar8327_sw_hw_apply,
+ .phy_rgmii_set = ar8327_phy_rgmii_set,
.num_mibs = ARRAY_SIZE(ar8236_mibs),
.mib_decs = ar8236_mibs,
diff --git a/target/linux/generic/files/drivers/net/phy/ar8327.h
b/target/linux/generic/files/drivers/net/phy/ar8327.h
index d53ef88..d79f14a 100644
--- a/target/linux/generic/files/drivers/net/phy/ar8327.h
+++ b/target/linux/generic/files/drivers/net/phy/ar8327.h
@@ -283,6 +283,13 @@
#define AR8337_PAD_MAC06_EXCHANGE_EN BIT(31)
+#define AR8327_PHY_MODE_SEL 0x12
+#define AR8327_PHY_MODE_SEL_RGMII BIT(3)
+#define AR8327_PHY_TEST_CTRL 0x0
+#define AR8327_PHY_TEST_CTRL_RGMII_RX_DELAY BIT(15)
+#define AR8327_PHY_SYS_CTRL 0x5
+#define AR8327_PHY_SYS_CTRL_RGMII_TX_DELAY BIT(8)
+
enum ar8327_led_pattern {
AR8327_LED_PATTERN_OFF = 0,
AR8327_LED_PATTERN_BLINK,
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel