Hi, On 29-07-19, David Hutchison wrote: > https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/412 > > I've been working on the hAP AC2 port, and haven't tested with SMP yet. > > I posted the DTS files I came up with on the RB3011 thread as we were all > working on Mikrotik IPQ40XX boards.
Thanks a lot, diff-ing against your DTS allowed me to spot the issue! The problem is that I was defining 256 MiB of RAM in the DTS, because that's what wikidevi says: https://wikidevi.com/wiki/MikroTik_RouterBOARD_hAP_ac_2_(RBD52G-5HacD2HnD-TC) It turns out that the board actually has 128 MiB of RAM (as shown by the bootloader and by examining the RAM chip). Defining more RAM than actually available booted fine with 1 CPU core, but not with the full 4 cores enabled. The FCC photos (used by wikidevi) do show a 256 MiB RAM chip, so Mikrotik probably decided later to ship with less RAM than anticipated. > I'm stuck on decompressing the WiFi radio calibration data , I can't seem > to figure out how to get the LZO / RLE portion to work. > I know exactly where the LZO / RLE data is as well. Ok, let's work together then :) > If you want, I'll try to enable SMP and see if my board boots. > If you have any insight on WiFi, please let me know. > > I'd like to help where I can. > > On Mon, Jul 29, 2019 at 4:10 PM Baptiste Jonglez < > bapti...@bitsofnetworks.org> wrote: > > > On 29-07-19, Hauke Mehrtens wrote: > > > On 7/29/19 11:25 AM, Baptiste Jonglez wrote: > > > > Is there something obviously wrong in the DTS? As far as I know, other > > > > ipq40xx devices don't have an issue with SMP. > > > > > > Did you try to revert this commit: > > > > > https://github.com/mmaker/openwrt/commit/481615d2f5e4bb053af805dccb901050e1e7a4ed > > > > > > The vendor dts file uses these 3 blocks, I do not know if they are > > > loaded to these regions by some boot loader or later by some driver. If > > > they are loaded there by the boot loader we should probably not use this > > > memory in Linux and let it run there. > > > > Yes, this commit is just a recent attempt to fix a warning during boot. > > The upstream DTS (qcom-ipq4019.dtsi) already reserves a memory region, > > exactly for the reasons you mention: > > https://patchwork.kernel.org/patch/10347459/ > > > > This reserved region in the dtsi is overlapping with the one in the DTS, > > and there was a warning during boot ("OVERLAP DETECTED" below). The > > commit did fix the warning, but did not change anything about the initial > > problem with SMP. > > > > > I attached the vendor.dts file we extracted from the flash of the board. > > > > Thanks, could you spot anything interesting in it? It looks very verbose. > > > > Baptiste > > > > > > PS: here is the failing bootlog, getting stuck after "Testing write > > buffer coherency": > > > > > > > > [ 0.000000] Booting Linux on physical CPU 0x0 > > > > [ 0.000000] Linux version 4.19.57 (bjonglez@gcc14) (gcc version > > 7.4.0 (OpenWrt GCC 7.4.0 r10506-a0c97101d6)) #0 SMP Mon Jul 29 08:51:07 2019 > > > > [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), > > cr=10c5387d > > > > [ 0.000000] CPU: div instructions available: patching division code > > > > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > > instruction cache > > > > [ 0.000000] OF: fdt: Machine model: Mikrotik RouterBOARD > > RBD52G-5HacD2HnD (hAP ac²) > > > > [ 0.000000] bootconsole [earlycon0] enabled > > > > [ 0.000000] Memory policy: Data cache writealloc > > > > [ 0.000000] OF: reserved mem: OVERLAP DETECTED! > > > > [ 0.000000] rsvd2@87B00000 (0x87b00000--0x88000000) overlaps with > > smem@87e00000 (0x87e00000--0x87e80000) > > > > [ 0.000000] random: get_random_bytes called from > > start_kernel+0x7c/0x438 with crng_init=0 > > > > [ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440 > > > > [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: > > 60864 > > > > [ 0.000000] Kernel command line: earlyprintk > > > > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, > > 131072 bytes) > > > > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 > > bytes) > > > > [ 0.000000] Memory: 232420K/245760K available (4720K kernel code, > > 168K rwdata, 1288K rodata, 3072K init, 231K bss, 13340K reserved, 0K > > cma-reserved, 0K highmem) > > > > [ 0.000000] Virtual kernel memory layout: > > > > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > > > > [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > > > > [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) > > > > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) > > > > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > > > > [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > > > > [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (5713 kB) > > > > [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (3072 kB) > > > > [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 168 kB) > > > > [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 232 kB) > > > > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, > > Nodes=1 > > > > [ 0.000000] rcu: Hierarchical RCU implementation. > > > > [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 > > > > [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). > > > > [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff > > max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns > > > > [ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps > > every 4398046511096ns > > > > [ 0.007985] Switching to timer-based delay loop, resolution 20ns > > > > [ 0.014242] Calibrating delay loop (skipped), value calculated > > using timer frequency.. 96.00 BogoMIPS (lpj=480000) > > > > [ 0.024315] pid_max: default: 32768 minimum: 301 > > > > [ 0.029081] Mount-cache hash table entries: 1024 (order: 0, 4096 > > bytes) > > > > [ 0.035524] Mountpoint-cache hash table entries: 1024 (order: 0, > > 4096 bytes) > > > > [ 0.043539] CPU: Testing write buffer coherency: ok > > > > > > > > > > > > Here is a working bootlog, same image but with "nosmp": > > > > > > > > [ 0.000000] Booting Linux on physical CPU 0x0 > > > > [ 0.000000] Linux version 4.19.57 (bjonglez@gcc14) (gcc version > > 7.4.0 (OpenWrt GCC 7.4.0 r10506-a0c97101d6)) #0 SMP Mon Jul 29 08:13:02 2019 > > > > [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), > > cr=10c5387d > > > > [ 0.000000] CPU: div instructions available: patching division code > > > > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > > instruction cache > > > > [ 0.000000] OF: fdt: Machine model: Mikrotik RouterBOARD > > RBD52G-5HacD2HnD (hAP ac²) > > > > [ 0.000000] bootconsole [earlycon0] enabled > > > > [ 0.000000] Memory policy: Data cache writealloc > > > > [ 0.000000] OF: reserved mem: OVERLAP DETECTED! > > > > [ 0.000000] rsvd2@87B00000 (0x87b00000--0x88000000) overlaps with > > smem@87e00000 (0x87e00000--0x87e80000) > > > > [ 0.000000] random: get_random_bytes called from > > start_kernel+0x7c/0x438 with crng_init=0 > > > > [ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440 > > > > [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: > > 60864 > > > > [ 0.000000] Kernel command line: earlyprintk nosmp > > > > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, > > 131072 bytes) > > > > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 > > bytes) > > > > [ 0.000000] Memory: 232420K/245760K available (4720K kernel code, > > 168K rwdata, 1288K rodata, 3072K init, 231K bss, 13340K reserved, 0K > > cma-reserved, 0K highmem) > > > > [ 0.000000] Virtual kernel memory layout: > > > > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > > > > [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > > > > [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) > > > > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) > > > > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > > > > [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > > > > [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (5713 kB) > > > > [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (3072 kB) > > > > [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 168 kB) > > > > [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 232 kB) > > > > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, > > Nodes=1 > > > > [ 0.000000] rcu: Hierarchical RCU implementation. > > > > [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 > > > > [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). > > > > [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff > > max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns > > > > [ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps > > every 4398046511096ns > > > > [ 0.007985] Switching to timer-based delay loop, resolution 20ns > > > > [ 0.014242] Calibrating delay loop (skipped), value calculated > > using timer frequency.. 96.00 BogoMIPS (lpj=480000) > > > > [ 0.024315] pid_max: default: 32768 minimum: 301 > > > > [ 0.029087] Mount-cache hash table entries: 1024 (order: 0, 4096 > > bytes) > > > > [ 0.035521] Mountpoint-cache hash table entries: 1024 (order: 0, > > 4096 bytes) > > > > [ 0.043529] CPU: Testing write buffer coherency: ok > > > > [ 0.048493] Setting up static identity map for 0x80300000 - > > 0x80300060 > > > > [ 0.054162] rcu: Hierarchical SRCU implementation. > > > > [ 0.059609] smp: Bringing up secondary CPUs ... > > > > [ 0.063282] smp: Brought up 1 node, 1 CPU > > > > [ 0.067274] SMP: Total of 1 processors activated (96.00 BogoMIPS). > > > > [ 0.073476] CPU: All CPU(s) started in SVC mode. > > > > [ 0.082314] VFP support v0.3: implementor 41 architecture 2 part 30 > > variant 7 rev 5 > > > > [ 0.089157] clocksource: jiffies: mask: 0xffffffff max_cycles: > > 0xffffffff, max_idle_ns: 19112604462750000 ns > > > > [ 0.098782] futex hash table entries: 1024 (order: 4, 65536 bytes) > > > > [ 0.105261] pinctrl core: initialized pinctrl subsystem > > > > [ 0.111253] NET: Registered protocol family 16 > > > > [ 0.115162] DMA: preallocated 256 KiB pool for atomic coherent > > allocations > > > > [ 0.122468] cpuidle: using governor ladder > > > > [ 0.125641] cpuidle: using governor menu > > > > [ 0.147920] usbcore: registered new interface driver usbfs > > > > [ 0.152432] usbcore: registered new interface driver hub > > > > [ 0.157828] usbcore: registered new device driver usb > > > > [ 0.162751] pps_core: LinuxPPS API ver. 1 registered > > > > [ 0.167657] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 > > Rodolfo Giometti <giome...@linux.it> > > > > [ 0.176824] PTP clock support registered > > > > [ 0.182206] clocksource: Switched to clocksource arch_sys_counter > > > > [ 0.188356] NET: Registered protocol family 2 > > > > [ 0.192405] tcp_listen_portaddr_hash hash table entries: 512 > > (order: 0, 6144 bytes) > > > > [ 0.199346] TCP established hash table entries: 2048 (order: 1, > > 8192 bytes) > > > > [ 0.206336] TCP bind hash table entries: 2048 (order: 2, 16384 > > bytes) > > > > [ 0.212745] TCP: Hash tables configured (established 2048 bind 2048) > > > > [ 0.219173] UDP hash table entries: 256 (order: 1, 8192 bytes) > > > > [ 0.224904] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) > > > > [ 0.231351] NET: Registered protocol family 1 > > > > [ 2.746607] No memory allocated for crashlog > > > > [ 2.750141] workingset: timestamp_bits=14 max_order=16 > > bucket_order=2 > > > > [ 2.761295] squashfs: version 4.0 (2009/01/31) Phillip Lougher > > > > [ 2.766200] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) > > (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. > > > > [ 2.782649] io scheduler noop registered > > > > [ 2.785548] io scheduler deadline registered (default) > > > > [ 2.793099] bam-dma-engine 8e04000.dma: num-channels unspecified in > > dt > > > > [ 2.798599] bam-dma-engine 8e04000.dma: num-ees unspecified in dt > > > > [ 2.806057] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 > > > > [ 2.810931] tcsr 194b000.tcsr: setting usb hs phy mode select = > > e700e7 > > > > [ 2.817492] tcsr 1953000.ess_tcsr: setting ess interface select = 0 > > > > [ 2.823714] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = > > 2222222 > > > > [ 2.830473] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled > > > > [ 2.837172] msm_serial 78af000.serial: msm_serial: detected port #0 > > > > [ 2.842873] msm_serial 78af000.serial: uartclk = 1843200 > > > > [ 2.848133] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, > > base_baud = 115200) is a MSM > > > > [ 2.856646] msm_serial: console setup �[ 2.861276] console > > [ttyMSM0] enabled > > > > [ 2.861276] console [ttyMSM0] enabled > > > > [ 2.867570] bootconsole [earlycon0] disabled > > > > [ 2.867570] bootconsole [earlycon0] disabled > > > > [ 2.876309] msm_serial: driver initialized > > > > [ 2.881720] loop: module loaded > > > > [ 2.883175] spi_qup 78b5000.spi: IN:block:16, fifo:64, > > OUT:block:16, fifo:64 > > > > [ 2.892706] random: fast init done > > > > [ 2.893893] m25p80 spi0.0: w25q128jv (16384 Kbytes) > > > > [ 2.895046] 6 fixed-partitions partitions found on MTD device spi0.0 > > > > [ 2.899777] Creating 6 MTD partitions on "spi0.0": > > > > [ 2.906415] 0x000000000000-0x000000023000 : "Qualcomm-boot1" > > > > [ 2.911807] 0x000000023000-0x000000080000 : "Qualcomm-boot2" > > > > [ 2.917503] 0x000000080000-0x00000008e000 : "RouterBoot" > > > > [ 2.923117] 0x00000008e000-0x00000008f000 : "hard_config" > > > > [ 2.928336] 0x000000090000-0x0000000a0000 : "dts_config" > > > > [ 2.933724] 0x0000000bd000-0x0000000be000 : "soft_config" > > > > [ 2.939783] libphy: ipq40xx_mdio: probed > > > > [ 3.021986] ESS reset ok! > > > > [ 3.054970] ESS reset ok! > > > > [ 3.473002] libphy: Fixed MDIO Bus: probed > > > > [ 3.474006] EDMA using MAC@ - using > > > > [ 3.474026] be:cf:22:8f:ab:1b > > > > [ 3.480289] EDMA using MAC@ - using > > > > [ 3.480301] ba:b5:bb:8b:4c:13 > > > > [ 3.582352] i2c /dev entries driver > > > > [ 3.589076] NET: Registered protocol family 10 > > > > [ 3.590761] Segment Routing with IPv6 > > > > [ 3.592617] NET: Registered protocol family 17 > > > > [ 3.596483] 8021q: 802.1Q VLAN Support v1.8 > > > > [ 3.600563] Registering SWP/SWPB emulation handler > > > > [ 3.611201] �[ 3.617293] Freeing unused kernel memory: 3072K > > > > [ 3.632992] Run /init as init process > > > > [ 3.658087] init: Console is alive > > > > [ 3.658335] init: - watchdog - > > > > [ 3.670018] kmodloader: loading kernel modules from > > /etc/modules-boot.d/* > > > > [ 3.682835] kmodloader: done loading kernel modules from > > /etc/modules-boot.d/* > > > > [ 3.693606] init: - preinit - > > > > [ 3.871306] random: jshn: uninitialized urandom read (4 bytes read) > > > > [ 3.904673] random: jshn: uninitialized urandom read (4 bytes read) > > > > [ 3.966511] random: jshn: uninitialized urandom read (4 bytes read) > > > > /bin/board_detect: line 10: Unsupported: not found > > > > Press the [f] key and hit [enter] to enter failsafe mode > > > > Press the [1], [2], [3] or [4] key and hit [enter] to select the debug > > level > > > > [ 7.223677] procd: - early - > > > > [ 7.223795] procd: - watchdog - > > > > [ 7.769990] procd: - watchdog - > > > > [ 7.773940] procd: - ubus - > > > > [ 7.788514] urandom_read: 5 callbacks suppressed > > > > [ 7.788528] random: ubusd: uninitialized urandom read (4 bytes read) > > > > [ 7.824888] random: ubusd: uninitialized urandom read (4 bytes read) > > > > [ 7.828410] procd: - init - > > > > Please press Enter to activate this console. > > > > [ 8.109693] urngd: v1.0.0 started. > > > > [ 8.151387] kmodloader: loading kernel modules from /etc/modules.d/* > > > > [ 8.183371] input: beeper as /devices/platform/beeper/input/input0 > > > > [ 8.194497] Loading modules backported from Linux version > > v4.19.32-0-g3a2156c839c7 > > > > [ 8.194532] Backport generated by backports.git > > v4.19.32-1-0-g1c4f7569 > > > > [ 8.224703] xt_time: kernel timezone is -0000 > > > > [ 8.263888] random: crng init done > > > > [ 8.270731] usbcore: registered new interface driver mt7601u > > > > [ 8.296351] PPP generic driver version 2.4.2 > > > > [ 8.298086] NET: Registered protocol family 24 > > > > [ 8.312402] usbcore: registered new interface driver mt76x0u > > > > [ 8.316366] kmodloader: done loading kernel modules from > > /etc/modules.d/* > > > > > > > > > > > > > > > > > > > _______________________________________________ > > openwrt-devel mailing list > > openwrt-devel@lists.openwrt.org > > https://lists.openwrt.org/mailman/listinfo/openwrt-devel > >
signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel