Hi, > -----Original Message----- > From: openwrt-devel [mailto:openwrt-devel-boun...@lists.openwrt.org] > On Behalf Of Ernst Spielmann > Sent: Donnerstag, 9. April 2020 19:27 > To: openwrt-devel@lists.openwrt.org > Cc: Ernst Spielmann <endsp...@disroot.org> > Subject: [OpenWrt-Devel] [PATCH 19.07 v2] ramips: add support for Asus RT- > N10P V3 / RT-N11P B1 / RT-N12 VP B1
I do not see this device in master.
Please submit a patch that is based on master.
Note that we do not add devices to stable branch without a special reason.
Concerning the content, since the names of these devices are different, and I
think the image should reflect that, I'd create three separate "devices" in
OpenWrt for them, and only use a shared DTSI to reduce code duplication. That
will be much more user-friendly at the end.
Best
Adrian
>
> Specifications:
>
> - MT7628NN @ 580 MHz
> - 32 MB RAM
> - 8 MB Flash
> - 5x 10/100 Mbps Ethernet (built-in switch)
> - 2.4 GHz WLAN
> - 2x external, non-detachable antennas (1x for RT-N10P V3)
>
> Flash instructions:
>
> 1. Set PC network interface to 192.168.1.75/24.
> 2. Connect PC to the router via LAN.
> 3. Turn router off, press and hold reset button, then turn it on.
> 4. Keep the button pressed till power led starts to blink.
> 5. Upload the firmware file via TFTP. (Any filename is accepted.) 6. Wait
> until
> the router reboots.
>
> Signed-off-by: Ernst Spielmann <endsp...@disroot.org>
> ---
> v2: RT-N12 VP *B1* was incorrectly mentioned as *B3* in mt76x8.mk
>
> target/linux/ramips/base-files/etc/board.d/01_leds | 5 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> target/linux/ramips/dts/RT-N11P_B1.dts | 125
> +++++++++++++++++++++
> target/linux/ramips/image/mt76x8.mk | 7 ++
> 5 files changed, 141 insertions(+)
> create mode 100644 target/linux/ramips/dts/RT-N11P_B1.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 5c005db0c1..c89af17d52 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -291,6 +291,11 @@ rp-n53)
> ucidef_set_led_netdev "eth" "Network" "$boardname:white:back"
> "eth0"
> set_wifi_led "$boardname:blue:wifi"
> ;;
> +rt-n11p_b1)
> + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0"
> "0xf"
> + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan"
> "switch0" "0x10"
> + ucidef_set_led_wlan "wlan" "wlan" "$boardname:green:wlan"
> "phy0tpt"
> + ;;
> rt-n12p)
> ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" eth0.1
> ucidef_set_led_netdev "wan" "wan" "$boardname:green:wan"
> eth0.2 diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index f743ce851a..4ea5cf0565 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -112,6 +112,7 @@ ramips_setup_interfaces()
> pbr-m1|\
> psg1208|\
> psg1218a|\
> + rt-n11p_b1|\
> rt-n12p|\
> sap-g3200u3|\
> sk-wb8|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index 093303892c..d1caa9d5ea 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -439,6 +439,9 @@ ramips_board_detect() {
> *"RT-N10+")
> name="rt-n10-plus"
> ;;
> + *"RT-N11P B1")
> + name="rt-n11p_b1"
> + ;;
> *"RT-N12+")
> name="rt-n12p"
> ;;
> diff --git a/target/linux/ramips/dts/RT-N11P_B1.dts
> b/target/linux/ramips/dts/RT-N11P_B1.dts
> new file mode 100644
> index 0000000000..d2824f8995
> --- /dev/null
> +++ b/target/linux/ramips/dts/RT-N11P_B1.dts
> @@ -0,0 +1,125 @@
> +/dts-v1/;
> +
> +#include "mt7628an.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + compatible = "asus,rt-n11p_b1", "mediatek,mt7628an-soc";
> + model = "Asus RT-N11P B1";
> +
> + aliases {
> + led-boot = &led_power;
> + led-failsafe = &led_power;
> + led-running = &led_power;
> + led-upgrade = &led_power;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,57600";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_power: power {
> + label = "rt-n11p_b1:green:power";
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + };
> +
> + wlan {
> + label = "rt-n11p_b1:green:wlan";
> + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + wan {
> + label = "rt-n11p_b1:green:wan";
> + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan {
> + label = "rt-n11p_b1:green:lan";
> + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + keys {
> + compatible = "gpio-keys-polled";
> + poll-interval = <20>;
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + m25p80@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <10000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition@30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition@40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition@50000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x50000 0x7b0000>;
> + };
> + };
> + };
> +};
> +
> +ðernet {
> + mtd-mac-address = <&factory 0x4>;
> + mediatek,portmap = <0x3e>;
> +};
> +
> +&wmac {
> + status = "okay";
> +};
> +
> +&state_default {
> + default {
> + ralink,group = "refclk";
> + ralink,function = "gpio";
> + };
> +};
> +
> +&usbphy {
> + status = "disabled";
> +};
> +
> +&ehci {
> + status = "disabled";
> +};
> +
> +&ohci {
> + status = "disabled";
> +};
> diff --git a/target/linux/ramips/image/mt76x8.mk
> b/target/linux/ramips/image/mt76x8.mk
> index 7df5c04297..b9c37c58a0 100644
> --- a/target/linux/ramips/image/mt76x8.mk
> +++ b/target/linux/ramips/image/mt76x8.mk
> @@ -175,6 +175,13 @@ define Device/rakwireless_rak633 endef
> TARGET_DEVICES += rakwireless_rak633
>
> +define Device/rt-n11p_b1
> + DTS := RT-N11P_B1
> + IMAGE_SIZE := $(ralink_default_fw_size_8M)
> + DEVICE_TITLE := Asus RT-N10P V3/RT-N11P B1/RT-N12 VP B1 endef
> +TARGET_DEVICES += rt-n11p_b1
> +
> define Device/skylab_skw92a
> DTS := SKW92A
> IMAGE_SIZE := 16064k
> --
> 2.14.5
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
openpgp-digital-signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
