Hello. I have just run-tested the patch from your tree on actual
hardware - the web GUI works fine, as do both internet and wireless
interfaces.
An investigation into the art partition has shown that there are four
sequential MAC addresses stored in memory.
The first and the third are back-to-back, addresses 0x0000 and 0x0006
respectively.
The second one is located at 0x1002, and the fourth one is at 0x5006. I
have no explanation for why it is like that.
To answer your question - it's not an exact match, but it's close to that.
P.S. Thank you for catching the v5/v6 difference - or lack of thereof,
rather.
On 2020-05-24 7:45 a.m., m...@adrianschmutzler.de wrote:
Hi,
-----Original Message-----
From: openwrt-devel [mailto:openwrt-devel-boun...@lists.openwrt.org]
On Behalf Of ad...@kryma.net
Sent: Freitag, 27. März 2020 04:33
To: openwrt-devel@lists.openwrt.org
Cc: Pavel Balan <ad...@kryma.net>
Subject: [OpenWrt-Devel] [PATCH v6] ath79: add support for COMFAST CF-
E130N v2
From: Pavel Balan <ad...@kryma.net>
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.
Specifications:
- QCA9531 SoC
- 1x 10/100 Mbps Ethernet with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 5 dBi built-in antenna
- POWER/LAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI.
The U-boot bootloader also contains a backup TFTP client to upload the
firmware from. Upon boot, it checks its ethernet network for the IP
192.168.1.10. Host a TFTP server and provide the image to be flashed as file
firmware_auto.bin.
Signed-off-by: Pavel Balan <ad...@kryma.net>
---
Run-tested on hardware.
Changes since v5:
Made partition@7e0000 read-only.
Changed IMAGE_SIZE to 7936k.
it looks like you have actually sent the v5 version of your patch again, as the
v6-changes you report are not included. Anyway, I've added these (and a few
others) myself and pushed the result to my staging tree here:
https://git.openwrt.org/?p=openwrt/staging/adrian.git;a=shortlog;h=refs/heads/staging
Please run this on your device and check whether everything is okay, so I can
merge this.
Despite, I'd be interested whether the MAC address from calibration data (art
0x1002) is actually the same as art 0x0, so we can drop mtd-mac-address from
wmac.
Best
Adrian
---
.../ath79/dts/qca9531_comfast_cf-e130n-v2.dts | 150
++++++++++++++++++
.../generic/base-files/etc/board.d/01_leds | 8 +
.../generic/base-files/etc/board.d/02_network | 1 +
target/linux/ath79/image/generic.mk | 10 ++
4 files changed, 169 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e130n-
v2.dts
diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
new file mode 100644
index 0000000000..dc1e037307
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+ compatible = "comfast,cf-e130n-v2", "qca,qca9531";
+ model = "COMFAST CF-E130N v2";
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_rssihigh;
+ led-failsafe = &led_rssihigh;
+ led-upgrade = &led_rssihigh;
+ label-mac-device = ð1;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+
+ wlan {
+ label = "cf-e130n-v2:green:wlan";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ lan {
+ label = "cf-e130n-v2:green:lan";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ unused {
+ label = "cf-e130n-v2:green:unused";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ rssilow {
+ label = "cf-e130n-v2:red:rssilow";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumlow {
+ label = "cf-e130n-v2:red:rssimediumlow";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumhigh {
+ label = "cf-e130n-v2:green:rssimediumhigh";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_rssihigh: rssihigh {
+ label = "cf-e130n-v2:green:rssihigh";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x010000>;
+ read-only;
+ };
+
+ art: partition@10000 {
+ label = "art";
+ reg = <0x010000 0x010000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x020000 0x7c0000>;
+ };
+
+ partition@7e0000 {
+ compatible = "denx,uimage";
+ label = "configs";
+ reg = <0x7e0000 0x010000>;
+ };
+
+ partition@7f0000 {
+ label = "nvram";
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+
+};
+
+ð0 {
+ compatible = "syscon", "simple-mfd";
+};
+
+ð1 {
+ status = "okay";
+
+ phy-handle = <&swphy0>;
+
+ mtd-mac-address = <&art 0x0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index fbb0d0ea03..3046d34605 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -47,6 +47,14 @@ comfast,cf-e120a-v3)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH"
"$boardname:green:rssihigh" "wlan0" "76" "100"
;;
+comfast,cf-e130n-v2)
+ ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow"
"wlan0" "1" "100"
+ ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW"
"$boardname:red:rssimediumlow" "wlan0" "26" "100"
+ ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
+ ucidef_set_led_rssi "rssihigh" "RSSIHIGH"
"$boardname:green:rssihigh" "wlan0" "76" "100"
+ ;;
comfast,cf-e313ac)
ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan"
"switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan"
"eth1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 10ca213e70..b1ecc066fd 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ ath79_setup_interfaces()
alfa-network,ap121f|\
aruba,ap-105|\
avm,fritz300e|\
+ comfast,cf-e130n-v2|\
devolo,dvl1200i|\
devolo,dvl1750c|\
devolo,dvl1750i|\
diff --git a/target/linux/ath79/image/generic.mk
b/target/linux/ath79/image/generic.mk
index 70631c20d0..256481ece3 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -258,6 +258,16 @@ define Device/comfast_cf-e120a-v3 endef
TARGET_DEVICES += comfast_cf-e120a-v3
+define Device/comfast_cf-e130n-v2
+ ATH_SOC := qca9531
+ DEVICE_VENDOR := COMFAST
+ DEVICE_MODEL := CF-E130N
+ DEVICE_VARIANT := v2
+ DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
+ IMAGE_SIZE := 8000k
+endef
+TARGET_DEVICES += comfast_cf-e130n-v2
+
define Device/comfast_cf-e313ac
ATH_SOC := qca9531
DEVICE_VENDOR := COMFAST
--
2.17.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
