Hi, I'd like to help to port R6100 to ath79. I've experience with serial interfaces/resetting/flashing/testing put not contributing code to openwrt. The WNDR4300SW and WNDR3700 v4 ath9 look technically similar to the R6100. Enclosed are relevant data [1] gathered running 19.07.7. Thanks in advance for your help.
Best Regards Thomas [1] https://openwrt.org/docs/guide-developer/adding_new_device dmesg [ 0.000000] Linux version 4.14.221 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11306-c4a6851c72)) #0 Mon Feb 15 15:22:37 2021 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 80538bc0, node_mem_map 81000020 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from 0x8053c740 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=R6100 console=ttyS0,115200 mtdparts=ar934x-nfc:128k(u-boot)ro,256k(caldata)ro,256k(caldata-backup),512k(config),512k(pot),2048k(kernel),122240k(ubi),25600k@0x1a0000(firmware),2048k(language),3072k(traffic_meter) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 124100K/131072K available (4263K kernel code, 176K rwdata, 528K rodata, 208K init, 213K bss, 6972K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns [ 0.000010] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns [ 0.008331] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.084944] pid_max: default: 32768 minimum: 301 [ 0.090073] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.097138] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.106953] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.117467] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.125182] NET: Registered protocol family 16 [ 0.131313] MIPS: machine is NETGEAR R6100 [ 0.135882] ar71xx: using random MAC address for eth0 [ 0.370229] ar71xx: using random MAC address for eth1 [ 0.614734] registering PCI controller with io_map_base unset [ 0.634182] PCI host bridge to bus 0000:00 [ 0.638561] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.645930] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.651858] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.659098] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.667564] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000 [ 0.667581] pci 0000:00:00.0: invalid calibration data [ 0.673104] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.673161] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.673243] pci 0000:00:00.0: supports D1 D2 [ 0.673468] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.673497] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.681294] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.692398] clocksource: Switched to clocksource MIPS [ 0.698855] NET: Registered protocol family 2 [ 0.704487] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.711916] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.718737] TCP: Hash tables configured (established 1024 bind 1024) [ 0.725663] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.731896] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.738870] NET: Registered protocol family 1 [ 0.743594] PCI: CLS 0 bytes, default 32 [ 0.746660] Crashlog allocated RAM at address 0x3f00000 [ 0.753637] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.765860] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.772065] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.793842] io scheduler noop registered [ 0.798021] io scheduler deadline registered (default) [ 0.803975] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.812914] console [ttyS0] disabled [ 0.836817] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.846027] console [ttyS0] enabled [ 0.853462] bootconsole [early0] disabled [ 0.869045] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1 [ 0.875543] nand: Micron NAND 128MiB 3,3V 8-bit [ 0.880145] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.887864] Scanning device for bad blocks [ 0.895339] random: fast init done [ 0.976126] 10 cmdlinepart partitions found on MTD device ar934x-nfc [ 0.982605] Creating 10 MTD partitions on "ar934x-nfc": [ 0.987919] 0x000000000000-0x000000020000 : "u-boot" [ 0.994371] 0x000000020000-0x000000060000 : "caldata" [ 1.001577] 0x000000060000-0x0000000a0000 : "caldata-backup" [ 1.008757] 0x0000000a0000-0x000000120000 : "config" [ 1.015908] 0x000000120000-0x0000001a0000 : "pot" [ 1.022046] 0x0000001a0000-0x0000003a0000 : "kernel" [ 1.029220] 0x0000003a0000-0x000007b00000 : "ubi" [ 1.036036] 0x0000001a0000-0x000001aa0000 : "firmware" [ 1.398042] 0x000001aa0000-0x000001ca0000 : "language" [ 1.405026] 0x000001ca0000-0x000001fa0000 : "traffic_meter" [ 1.412868] libphy: Fixed MDIO Bus: probed [ 1.429325] libphy: ag71xx_mdio: probed [ 2.064374] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY] [ 2.074265] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 2.704285] ag71xx-mdio.1: Found an AR934X built-in switch [ 2.756475] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 2.764931] NET: Registered protocol family 10 [ 2.774940] Segment Routing with IPv6 [ 2.778777] NET: Registered protocol family 17 [ 2.783396] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.797115] 8021q: 802.1Q VLAN Support v1.8 [ 2.805228] UBI: auto-attach mtd6 [ 2.808625] ubi0: attaching mtd6 [ 3.831874] random: crng init done [ 4.139094] ubi0: fixable bit-flip detected at PEB 868 [ 4.281654] ubi0: scanning is finished [ 4.303050] ubi0: attached mtd6 (name "ubi", size 119 MiB) [ 4.308626] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.315655] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.322555] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.329612] ubi0: good PEBs: 955, bad PEBs: 0, corrupted PEBs: 0 [ 4.335718] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.343060] ubi0: max/mean erase counter: 48/8, WL threshold: 4096, image sequence number: 1540979924 [ 4.352429] ubi0: available PEBs: 0, total reserved PEBs: 955, PEBs reserved for bad PEB handling: 20 [ 4.361826] ubi0: background thread "ubi_bgt0d" started, PID 345 [ 4.369561] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.375204] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.382268] hctosys: unable to open rtc device (rtc0) [ 4.395961] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.404294] Freeing unused kernel memory: 208K [ 4.408801] This architecture does not have kernel memory protection. [ 5.003439] init: Console is alive [ 5.007139] init: - watchdog - [ 6.175017] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.233045] usbcore: registered new interface driver usbfs [ 6.238681] usbcore: registered new interface driver hub [ 6.244215] usbcore: registered new device driver usb [ 6.255127] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.263585] ehci-platform: EHCI generic platform driver [ 6.268985] ehci-platform ehci-platform: EHCI Host Controller [ 6.274925] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 6.285077] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 6.312435] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 6.319606] hub 1-0:1.0: USB hub found [ 6.323888] hub 1-0:1.0: 1 port detected [ 6.329114] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.346960] init: - preinit - [ 6.792436] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 7.440055] print_req_error: I/O error, dev mtdblock1, sector 8 [ 7.486118] print_req_error: I/O error, dev mtdblock1, sector 8 [ 7.540100] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.870280] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 435 [ 10.974478] UBIFS (ubi0:1): recovery needed [ 11.188920] UBIFS (ubi0:1): recovery completed [ 11.193599] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 11.201546] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.211634] UBIFS (ubi0:1): FS size: 113643520 bytes (108 MiB, 895 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs) [ 11.222407] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 11.229118] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID C395A2AD-AD8B-4340-8097-601A5CC7ACDC, small LPT model [ 11.254929] mount_root: loading kmods from internal overlay [ 11.361568] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 11.651806] SCSI subsystem initialized [ 11.685083] usb-storage 1-1:1.0: USB Mass Storage device detected [ 11.691648] scsi host0: usb-storage 1-1:1.0 [ 11.696475] usbcore: registered new interface driver usb-storage [ 11.704131] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 11.756844] print_req_error: I/O error, dev mtdblock0, sector 48 [ 11.776335] print_req_error: I/O error, dev mtdblock1, sector 8 [ 11.804299] print_req_error: I/O error, dev mtdblock1, sector 8 [ 11.810320] Buffer I/O error on dev mtdblock1, logical block 1, async page read [ 12.037864] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 12.052715] block: extroot: not configured [ 12.060361] mount_root: switching to ubifs overlay [ 12.100039] urandom-seed: Seeding with /etc/urandom.seed [ 12.325024] procd: - early - [ 12.328053] procd: - watchdog - [ 12.764773] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2 [ 12.777045] sd 0:0:0:0: [sda] 3891200 512-byte logical blocks: (1.99 GB/1.86 GiB) [ 12.792943] sd 0:0:0:0: [sda] Write Protect is off [ 12.797824] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 12.802571] sd 0:0:0:0: [sda] No Caching mode page found [ 12.808014] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 12.829470] sda: sda1 [ 12.836965] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 13.333169] procd: - watchdog - [ 13.336698] procd: - ubus - [ 13.498417] procd: - init - [ 14.483986] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.579284] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 14.614517] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b [ 14.622293] Backport generated by backports.git v4.19.161-1-0-g4bb568fe [ 14.655135] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.679966] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 14.855435] urngd: v1.0.2 started. [ 14.898912] xt_time: kernel timezone is -0000 [ 15.178479] PPP generic driver version 2.4.2 [ 15.193497] NET: Registered protocol family 24 [ 15.265662] pci 0000:00:00.0: using irq 40 for pin 1 [ 15.270719] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x3c. [ 15.293351] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 15.299271] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 15.614036] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2 [ 15.624776] ath10k_pci 0000:00:00.0: Falling back to user helper [ 15.987905] EXT4-fs (sda1): recovery complete [ 16.002436] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: [ 16.189996] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed [ 16.199299] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 16.210198] ath10k_pci 0000:00:00.0: Falling back to user helper [ 16.397987] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 16.409656] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2 [ 16.420840] ath10k_pci 0000:00:00.0: Falling back to user helper [ 16.608683] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 16.618412] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2 [ 16.629577] ath10k_pci 0000:00:00.0: Falling back to user helper [ 16.815806] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 16.825538] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2 [ 16.836441] ath10k_pci 0000:00:00.0: Falling back to user helper [ 17.024604] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 17.034073] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2 [ 17.044974] ath10k_pci 0000:00:00.0: Falling back to user helper [ 17.234309] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed [ 17.243773] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2 [ 17.254678] ath10k_pci 0000:00:00.0: Falling back to user helper [ 17.443044] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed [ 17.452507] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2 [ 17.463389] ath10k_pci 0000:00:00.0: Falling back to user helper [ 17.651882] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed [ 17.667030] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000 [ 17.676464] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 17.690148] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-538f0906 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 e1c91a74 [ 17.803158] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 17.813794] ath10k_pci 0000:00:00.0: Falling back to user helper [ 17.932862] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 17.942270] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 18.895208] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 18.913188] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410' [ 18.919568] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 18.927733] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 20984 iram: 25656' [ 18.984928] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 19.000179] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 19.136267] ath: EEPROM regdomain: 0x0 [ 19.136276] ath: EEPROM indicates default country code should be used [ 19.136280] ath: doing EEPROM country->regdmn map search [ 19.136297] ath: country maps to regdmn code: 0x3a [ 19.136303] ath: Country alpha2 being used: US [ 19.136308] ath: Regpair used: 0x3a [ 19.277961] ath: EEPROM regdomain: 0x0 [ 19.277971] ath: EEPROM indicates default country code should be used [ 19.277975] ath: doing EEPROM country->regdmn map search [ 19.277992] ath: country maps to regdmn code: 0x3a [ 19.277998] ath: Country alpha2 being used: US [ 19.278002] ath: Regpair used: 0x3a [ 19.292178] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 19.294346] ieee80211 phy1: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47 [ 19.332916] kmodloader: done loading kernel modules from /etc/modules.d/* [ 33.714606] print_req_error: I/O error, dev mtdblock0, sector 48 [ 33.768164] print_req_error: I/O error, dev mtdblock1, sector 8 [ 33.815148] print_req_error: I/O error, dev mtdblock1, sector 8 [ 33.821173] Buffer I/O error on dev mtdblock1, logical block 1, async page read [ 41.590254] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 41.638425] br-lan: port 1(eth1.1) entered blocking state [ 41.643978] br-lan: port 1(eth1.1) entered disabled state [ 41.649795] device eth1.1 entered promiscuous mode [ 41.654716] device eth1 entered promiscuous mode [ 41.782686] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 44.431039] ath: EEPROM regdomain: 0x8024 [ 44.435170] ath: EEPROM indicates we should expect a country code [ 44.441346] ath: doing EEPROM country->regdmn map search [ 44.446761] ath: country maps to regdmn code: 0x3b [ 44.451617] ath: Country alpha2 being used: AU [ 44.456140] ath: Regpair used: 0x3b [ 44.459679] ath: regdomain 0x8024 dynamically updated by user [ 44.465607] ath: EEPROM regdomain: 0x8024 [ 44.469673] ath: EEPROM indicates we should expect a country code [ 44.475875] ath: doing EEPROM country->regdmn map search [ 44.481263] ath: country maps to regdmn code: 0x3b [ 44.486137] ath: Country alpha2 being used: AU [ 44.490644] ath: Regpair used: 0x3b [ 44.494200] ath: regdomain 0x8024 dynamically updated by user [ 45.433371] ath: EEPROM regdomain: 0x8028 [ 45.437447] ath: EEPROM indicates we should expect a country code [ 45.443684] ath: doing EEPROM country->regdmn map search [ 45.449069] ath: country maps to regdmn code: 0x37 [ 45.453948] ath: Country alpha2 being used: AT [ 45.458450] ath: Regpair used: 0x37 [ 45.461990] ath: regdomain 0x8028 dynamically updated by user [ 45.467921] ath: EEPROM regdomain: 0x8028 [ 45.471984] ath: EEPROM indicates we should expect a country code [ 45.478188] ath: doing EEPROM country->regdmn map search [ 45.483591] ath: country maps to regdmn code: 0x37 [ 45.488450] ath: Country alpha2 being used: AT [ 45.492972] ath: Regpair used: 0x37 [ 45.496511] ath: regdomain 0x8028 dynamically updated by user [ 48.534990] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 50.190172] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 50.208178] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410' [ 50.214359] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 50.223078] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 20984 iram: 25656' [ 50.307031] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware [ 50.323908] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready [ 50.330173] br-lan: port 2(wlan1) entered blocking state [ 50.335633] br-lan: port 2(wlan1) entered disabled state [ 50.341326] device wlan1 entered promiscuous mode [ 50.356632] br-lan: port 3(wlan0-1) entered blocking state [ 50.362214] br-lan: port 3(wlan0-1) entered disabled state [ 50.368342] device wlan0-1 entered promiscuous mode [ 50.393416] ath: EEPROM regdomain: 0x8024 [ 50.397496] ath: EEPROM indicates we should expect a country code [ 50.403740] ath: doing EEPROM country->regdmn map search [ 50.409129] ath: country maps to regdmn code: 0x3b [ 50.414022] ath: Country alpha2 being used: AU [ 50.418610] ath: Regpair used: 0x3b [ 50.422155] ath: regdomain 0x8024 dynamically updated by user [ 50.428103] ath: EEPROM regdomain: 0x8024 [ 50.432165] ath: EEPROM indicates we should expect a country code [ 50.438375] ath: doing EEPROM country->regdmn map search [ 50.443795] ath: country maps to regdmn code: 0x3b [ 50.448649] ath: Country alpha2 being used: AU [ 50.453175] ath: Regpair used: 0x3b [ 50.456710] ath: regdomain 0x8024 dynamically updated by user [ 50.587716] ath: EEPROM regdomain: 0x8028 [ 50.591911] ath: EEPROM indicates we should expect a country code [ 50.598244] ath: doing EEPROM country->regdmn map search [ 50.603674] ath: country maps to regdmn code: 0x37 [ 50.608529] ath: Country alpha2 being used: AT [ 50.613051] ath: Regpair used: 0x37 [ 50.616591] ath: regdomain 0x8028 dynamically updated by user [ 50.622521] ath: EEPROM regdomain: 0x8028 [ 50.626680] ath: EEPROM indicates we should expect a country code [ 50.632900] ath: doing EEPROM country->regdmn map search [ 50.638289] ath: country maps to regdmn code: 0x37 [ 50.643165] ath: Country alpha2 being used: AT [ 50.647669] ath: Regpair used: 0x37 [ 50.651209] ath: regdomain 0x8028 dynamically updated by user [ 58.848191] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 58.854993] br-lan: port 2(wlan1) entered blocking state [ 58.860402] br-lan: port 2(wlan1) entered forwarding state [ 58.879950] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready cat /proc/cmdline board=R6100 console=ttyS0,115200 mtdparts=ar934x-nfc:128k(u-boot)ro,256k(caldata)ro,256k(caldata-backup),512k(config),512k(pot),2048k(kernel),122240k(ubi),25600k@0x1a0000(firmware),2048k(language),3072k(traffic_meter) rootfstype=squashfs noinitrd cat /proc/cpuinfo system type : Atheros AR9344 rev 2 machine : NETGEAR R6100 processor : 0 cpu model : MIPS 74Kc V4.12 BogoMIPS : 278.93 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] isa : mips1 mips2 mips32r1 mips32r2 ASEs implemented : mips16 dsp dsp2 Options implemented : tlb 4kex 4k_cache prefetch mcheck ejtag llsc dc_aliases perf_cntr_intr_bit nan_legacy nan_2008 perf shadow register sets : 1 kscratch registers : 0 package : 0 core : 0 VCED exceptions : not available VCEI exceptions : not available cat /proc/meminfo MemTotal: 124308 kB MemFree: 48760 kB MemAvailable: 35732 kB Buffers: 6864 kB Cached: 12996 kB SwapCached: 0 kB Active: 33188 kB Inactive: 8452 kB Active(anon): 21836 kB Inactive(anon): 32 kB Active(file): 11352 kB Inactive(file): 8420 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 4 kB Writeback: 0 kB AnonPages: 21788 kB Mapped: 4392 kB Shmem: 92 kB Slab: 8948 kB SReclaimable: 3316 kB SUnreclaim: 5632 kB KernelStack: 408 kB PageTables: 324 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 62152 kB Committed_AS: 25248 kB VmallocTotal: 1048372 kB VmallocUsed: 0 kB VmallocChunk: 0 kB cat /proc/devices Character devices: 1 mem 4 ttyS 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 90 mtd 108 ppp 128 ptm 136 pts 180 usb 189 usb_device 251 ubi0 252 watchdog 253 rtc 254 gpiochip Block devices: 8 sd 31 mtdblock 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd 254 ubiblock 259 blkext ls /sys/devices/platform Fixed MDIO bus.0 ag71xx-mdio.1 ag71xx.0 ag71xx.1 alarmtimer ar724x-pci ar934x-nfc ar934x_wmac ath79-gpio ath79-wdt ehci-platform gpio-keys-polled leds-gpio regulatory.0 serial8250 serial8250.0 uevent cat /proc/mtd dev: size erasesize name mtd0: 00020000 00020000 "u-boot" mtd1: 00040000 00020000 "caldata" mtd2: 00040000 00020000 "caldata-backup" mtd3: 00080000 00020000 "config" mtd4: 00080000 00020000 "pot" mtd5: 00200000 00020000 "kernel" mtd6: 07760000 00020000 "ubi" mtd7: 01900000 00020000 "firmware" mtd8: 00200000 00020000 "language" mtd9: 00300000 00020000 "traffic_meter" cat /sys/class/mtd/mtd*/offset 0 131072 393216 655360 1179648 1703936 3801088 1703936 27918336 30015488 ifconfig -a br-lan Link encap:Ethernet HWaddr E4:F4:C6:F4:76:52 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e6f4:c6ff:fef4:7652/64 Scope:Link inet6 addr: fd5c:467a:1dd7::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22047 errors:0 dropped:0 overruns:0 frame:0 TX packets:17047 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1337715 (1.2 MiB) TX bytes:1127243 (1.0 MiB) eth0 Link encap:Ethernet HWaddr E4:F4:C6:F4:76:53 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:4 eth1 Link encap:Ethernet HWaddr E4:F4:C6:F4:76:52 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:5 eth1.1 Link encap:Ethernet HWaddr E4:F4:C6:F4:76:52 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:14975 errors:0 dropped:0 overruns:0 frame:0 TX packets:14975 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1121966 (1.0 MiB) TX bytes:1121966 (1.0 MiB) wlan0 Link encap:Ethernet HWaddr E4:F4:C6:F4:76:54 inet6 addr: fe80::e6f4:c6ff:fef4:7654/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:355340 errors:0 dropped:0 overruns:0 frame:0 TX packets:197408 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:358958926 (342.3 MiB) TX bytes:31615152 (30.1 MiB) wlan0-1 Link encap:Ethernet HWaddr E6:F4:C6:F4:76:54 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan1 Link encap:Ethernet HWaddr E4:F4:C6:F4:76:52 inet6 addr: fe80::e6f4:c6ff:fef4:7652/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:195643 errors:0 dropped:0 overruns:0 frame:0 TX packets:355083 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26267406 (25.0 MiB) TX bytes:367850439 (350.8 MiB) ls /sys/class/net br-lan eth0 eth1 eth1.1 lo wlan0 wlan0-1 wlan1 brctl show bridge name bridge id STP enabled interfaces br-lan 7fff.e4f4c6f47652 no eth1.1 wlan1 wlan0-1 wlan0 cat /sys/kernel/debug/gpio gpiochip0: GPIOs 0-31, parent: platform/ath79-gpio, ath79-gpio: gpio-0 ( |netgear:blue:wlan ) out lo gpio-1 ( |RFKILL switch ) in hi gpio-3 ( |WPS button ) in hi gpio-11 ( |netgear:blue:usb ) out lo gpio-12 ( |Reset button ) in hi gpio-13 ( |netgear:green:wan ) out hi gpio-14 ( |netgear:amber:power ) out hi gpio-15 ( |netgear:amber:wan ) out hi gpio-16 ( |USB power ) out hi gpio-17 ( |netgear:green:power ) out lo gpiochip1: GPIOs 489-511, ath9k-phy1: gpio-490 ( |ath9k-phy1 ) in lo _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
