--- Begin Message ---
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1]
https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.bez...@microchip.com>
---
package/boot/at91bootstrap/Makefile | 14 +
package/boot/uboot-at91/Makefile | 14 +
target/linux/at91/image/sama5.mk | 11 +
.../at91/patches-5.4/106-add-wlsom1.patch | 600 ++++++++++++++++++
4 files changed, 639 insertions(+)
create mode 100644 target/linux/at91/patches-5.4/106-add-wlsom1.patch
diff --git a/package/boot/at91bootstrap/Makefile
b/package/boot/at91bootstrap/Makefile
index 56e14c57703c..8711acd286bd 100644
--- a/package/boot/at91bootstrap/Makefile
+++ b/package/boot/at91bootstrap/Makefile
@@ -118,6 +118,18 @@ define AT91Bootstrap/sama5d27_som1_ekqspi_uboot
BUILD_DEVICES:=microchip_sama5d27-som1-ek
endef
+define AT91Bootstrap/sama5d27_wlsom1_eksd_uboot
+ TITLE:=AT91Bootstrap for SAMA5D27 WLSOM1 Ek (SDcard0)
+ BUILD_SUBTARGET:=sama5
+ BUILD_DEVICES:=microchip_sama5d27-wlsom1-ek
+endef
+
+define AT91Bootstrap/sama5d27_wlsom1_ekdf_qspi_uboot
+ TITLE:=AT91Bootstrap for SAMA5D27 WLSOM1 Ek (QSPI Flash)
+ BUILD_SUBTARGET:=sama5
+ BUILD_DEVICES:=microchip_sama5d27-wlsom1-ek
+endef
+
define AT91Bootstrap/sama5d2_ptc_eknf_uboot
TITLE:=AT91Bootstrap for SAMA5D2 PTC EK (Nand Flash)
BUILD_SUBTARGET:=sama5
@@ -145,6 +157,8 @@ AT91BOOTSTRAP_TARGETS := \
sama5d4_xplainedsd_uboot_secure \
sama5d27_som1_eksd1_uboot \
sama5d27_som1_ekqspi_uboot \
+ sama5d27_wlsom1_eksd_uboot \
+ sama5d27_wlsom1_ekdf_qspi_uboot \
sama5d2_ptc_eknf_uboot \
sama5d2_ptc_eksd_uboot
diff --git a/package/boot/uboot-at91/Makefile b/package/boot/uboot-at91/Makefile
index 193f26dae471..5aade7de9cf9 100644
--- a/package/boot/uboot-at91/Makefile
+++ b/package/boot/uboot-at91/Makefile
@@ -107,6 +107,18 @@ define U-Boot/sama5d27_som1_ek_qspiflash
BUILD_DEVICES:=microchip_sama5d27-som1-ek
endef
+define U-Boot/sama5d27_wlsom1_ek_mmc
+ NAME:=SAMA5D27 WLSOM1 Ek (SDCard)
+ BUILD_SUBTARGET:=sama5
+ BUILD_DEVICES:=microchip_sama5d27-wlsom1-ek
+endef
+
+define U-Boot/sama5d27_wlsom1_ek_qspiflash
+ NAME:=SAMA5D27 WLSOM1 Ek (QSPI Flash)
+ BUILD_SUBTARGET:=sama5
+ BUILD_DEVICES:=microchip_sama5d27-wlsom1-ek
+endef
+
define U-Boot/sama5d2_ptc_ek_nandflash
NAME:=SAMA5D2 PTC Ek (Nand Flash)
BUILD_SUBTARGET:=sama5
@@ -133,6 +145,8 @@ UBOOT_TARGETS := \
sama5d4_xplained_nandflash\
sama5d27_som1_ek_mmc1 \
sama5d27_som1_ek_qspiflash \
+ sama5d27_wlsom1_ek_mmc \
+ sama5d27_wlsom1_ek_qspiflash \
sama5d2_ptc_ek_nandflash \
sama5d2_ptc_ek_mmc
diff --git a/target/linux/at91/image/sama5.mk b/target/linux/at91/image/sama5.mk
index d02d09e835ec..af1ef44dc83a 100644
--- a/target/linux/at91/image/sama5.mk
+++ b/target/linux/at91/image/sama5.mk
@@ -87,6 +87,17 @@ define Device/microchip_sama5d27-som1-ek
endef
TARGET_DEVICES += microchip_sama5d27-som1-ek
+define Device/microchip_sama5d27-wlsom1-ek
+ $(Device/evaluation-dtb)
+ DEVICE_VENDOR := Microchip
+ DEVICE_MODEL := SAMA5D27 WSOM1 Ek
+ DEVICE_DTS := at91-sama5d27_wlsom1_ek
+ SUPPORTED_DEVICES := microchip,sama5d27-wlsom1-ek
+ KERNEL_SIZE := 6144k
+ $(Device/evaluation-sdimage)
+endef
+TARGET_DEVICES += microchip_sama5d27-wlsom1-ek
+
define Device/microchip_sama5d2-ptc-ek
$(Device/evaluation-dtb)
DEVICE_VENDOR := Microchip
diff --git a/target/linux/at91/patches-5.4/106-add-wlsom1.patch
b/target/linux/at91/patches-5.4/106-add-wlsom1.patch
new file mode 100644
index 000000000000..9d86aadd0da7
--- /dev/null
+++ b/target/linux/at91/patches-5.4/106-add-wlsom1.patch
@@ -0,0 +1,600 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
+ at91-kizbox2.dtb \
+ at91-nattis-2-natte-2.dtb \
+ at91-sama5d27_som1_ek.dtb \
++ at91-sama5d27_wlsom1_ek.dtb \
+ at91-sama5d2_icp.dtb \
+ at91-sama5d2_ptc_ek.dtb \
+ at91-sama5d2_xplained.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+@@ -0,0 +1,314 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++/*
++ * at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1
++ *
++ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
++ *
++ * Author: Nicolas Ferre <nicolas.fe...@microcihp.com>
++ * Author: Eugen Hristev <eugen.hris...@microcihp.com>
++ */
++#include "sama5d2.dtsi"
++#include "sama5d2-pinfunc.h"
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/mfd/atmel-flexcom.h>
++#include <dt-bindings/pinctrl/at91.h>
++
++/ {
++ model = "Microchip SAMA5D27 WLSOM1";
++ compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27",
"atmel,sama5d2", "atmel,sama5";
++
++ aliases {
++ i2c0 = &i2c0;
++ };
++
++ clocks {
++ slow_xtal {
++ clock-frequency = <32768>;
++ };
++
++ main_xtal {
++ clock-frequency = <24000000>;
++ };
++ };
++};
++
++&flx1 {
++ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
++
++ uart6: serial@200 {
++ pinctrl-0 = <&pinctrl_flx1_default>;
++ pinctrl-names = "default";
++ };
++};
++
++&i2c0 {
++ pinctrl-0 = <&pinctrl_i2c0_default>;
++ pinctrl-1 = <&pinctrl_i2c0_gpio>;
++ pinctrl-names = "default", "gpio";
++ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
++ scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
++ status = "okay";
++};
++
++&i2c1 {
++ dmas = <0>, <0>;
++ pinctrl-names = "default", "gpio";
++ pinctrl-0 = <&pinctrl_i2c1_default>;
++ pinctrl-1 = <&pinctrl_i2c1_gpio>;
++ sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
++ scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
++ status = "okay";
++
++ mcp16502@5b {
++ compatible = "microchip,mcp16502";
++ reg = <0x5b>;
++ status = "okay";
++ lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
++
++ regulators {
++ vdd_3v3: VDD_IO {
++ regulator-name = "VDD_IO";
++ regulator-min-microvolt = <1200000>;
++ regulator-max-microvolt = <3700000>;
++ regulator-initial-mode = <2>;
++ regulator-allowed-modes = <2>, <4>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ regulator-mode = <4>;
++ };
++
++ regulator-state-mem {
++ regulator-off-in-suspend;
++ regulator-mode = <4>;
++ };
++ };
++
++ vddio_ddr: VDD_DDR {
++ regulator-name = "VDD_DDR";
++ regulator-min-microvolt = <600000>;
++ regulator-max-microvolt = <1850000>;
++ regulator-initial-mode = <2>;
++ regulator-allowed-modes = <2>, <4>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ regulator-suspend-microvolt = <1200000>;
++ regulator-changeable-in-suspend;
++ regulator-mode = <4>;
++ };
++
++ regulator-state-mem {
++ regulator-on-in-suspend;
++ regulator-suspend-microvolt = <1200000>;
++ regulator-changeable-in-suspend;
++ regulator-mode = <4>;
++ };
++ };
++
++ vdd_core: VDD_CORE {
++ regulator-name = "VDD_CORE";
++ regulator-min-microvolt = <600000>;
++ regulator-max-microvolt = <1850000>;
++ regulator-initial-mode = <2>;
++ regulator-allowed-modes = <2>, <4>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ regulator-mode = <4>;
++ };
++
++ regulator-state-mem {
++ regulator-off-in-suspend;
++ regulator-mode = <4>;
++ };
++ };
++
++ vdd_ddr: VDD_OTHER {
++ regulator-name = "VDD_OTHER";
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <1800000>;
++ regulator-initial-mode = <2>;
++ regulator-allowed-modes = <2>, <4>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ regulator-suspend-microvolt = <1800000>;
++ regulator-changeable-in-suspend;
++ regulator-mode = <4>;
++ };
++
++ regulator-state-mem {
++ regulator-on-in-suspend;
++ regulator-suspend-microvolt = <1800000>;
++ regulator-changeable-in-suspend;
++ regulator-mode = <4>;
++ };
++ };
++
++ LDO1 {
++ regulator-name = "LDO1";
++ regulator-min-microvolt = <1200000>;
++ regulator-max-microvolt = <3700000>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ };
++
++ regulator-state-mem {
++ regulator-off-in-suspend;
++ };
++ };
++
++ LDO2 {
++ regulator-name = "LDO2";
++ regulator-min-microvolt = <1200000>;
++ regulator-max-microvolt = <3700000>;
++ regulator-always-on;
++
++ regulator-state-standby {
++ regulator-on-in-suspend;
++ };
++
++ regulator-state-mem {
++ regulator-off-in-suspend;
++ };
++ };
++ };
++ };
++};
++
++&macb0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_macb0_default>;
++ phy-mode = "rmii";
++
++ ethernet-phy@0 {
++ reg = <0x0>;
++ interrupt-parent = <&pioA>;
++ interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_macb0_phy_irq>;
++ };
++};
++
++&pmc {
++ atmel,osc-bypass;
++};
++
++&qspi1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_qspi1_default>;
++ status = "disabled";
++
++ qspi1_flash: spi_flash@0 {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ compatible = "jedec,spi-nor";
++ reg = <0>;
++ spi-max-frequency = <80000000>;
++ spi-rx-bus-width = <4>;
++ spi-tx-bus-width = <4>;
++ m25p,fast-read;
++ status = "disabled";
++
++ at91bootstrap@0 {
++ label = "at91bootstrap";
++ reg = <0x0 0x40000>;
++ };
++
++ bootloader@40000 {
++ label = "bootloader";
++ reg = <0x40000 0xc0000>;
++ };
++
++ bootloaderenvred@100000 {
++ label = "bootloader env redundant";
++ reg = <0x100000 0x40000>;
++ };
++
++ bootloaderenv@140000 {
++ label = "bootloader env";
++ reg = <0x140000 0x40000>;
++ };
++
++ dtb@180000 {
++ label = "device tree";
++ reg = <0x180000 0x80000>;
++ };
++
++ kernel@200000 {
++ label = "kernel";
++ reg = <0x200000 0x600000>;
++ };
++ };
++};
++
++&pioA {
++ pinctrl_flx1_default: flx1_usart_default {
++ pinmux = <PIN_PA24__FLEXCOM1_IO0>,
++ <PIN_PA23__FLEXCOM1_IO1>,
++ <PIN_PA25__FLEXCOM1_IO3>,
++ <PIN_PA26__FLEXCOM1_IO4>;
++ bias-disable;
++ };
++
++ pinctrl_i2c0_default: i2c0_default {
++ pinmux = <PIN_PD21__TWD0>,
++ <PIN_PD22__TWCK0>;
++ bias-disable;
++ };
++
++ pinctrl_i2c0_gpio: i2c0_gpio {
++ pinmux = <PIN_PD21__GPIO>,
++ <PIN_PD22__GPIO>;
++ bias-disable;
++ };
++
++ pinctrl_i2c1_default: i2c1_default {
++ pinmux = <PIN_PD19__TWD1>,
++ <PIN_PD20__TWCK1>;
++ bias-disable;
++ };
++
++ pinctrl_i2c1_gpio: i2c1_gpio {
++ pinmux = <PIN_PD19__GPIO>,
++ <PIN_PD20__GPIO>;
++ bias-disable;
++ };
++
++ pinctrl_macb0_default: macb0_default {
++ pinmux = <PIN_PB14__GTXCK>,
++ <PIN_PB15__GTXEN>,
++ <PIN_PB16__GRXDV>,
++ <PIN_PB17__GRXER>,
++ <PIN_PB18__GRX0>,
++ <PIN_PB19__GRX1>,
++ <PIN_PB20__GTX0>,
++ <PIN_PB21__GTX1>,
++ <PIN_PB22__GMDC>,
++ <PIN_PB23__GMDIO>;
++ bias-disable;
++ };
++
++ pinctrl_macb0_phy_irq: macb0_phy_irq {
++ pinmux = <PIN_PB24__GPIO>;
++ bias-disable;
++ };
++
++ pinctrl_qspi1_default: qspi1_default {
++ pinmux = <PIN_PB5__QSPI1_SCK>,
++ <PIN_PB6__QSPI1_CS>,
++ <PIN_PB7__QSPI1_IO0>,
++ <PIN_PB8__QSPI1_IO1>,
++ <PIN_PB9__QSPI1_IO2>,
++ <PIN_PB10__QSPI1_IO3>;
++ bias-pull-up;
++ };
++};
++
+--- /dev/null
++++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
+@@ -0,0 +1,270 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++/*
++ * at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
++ *
++ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
++ *
++ * Author: Nicolas Ferre <nicolas.fe...@microcihp.com>
++ */
++/dts-v1/;
++#include "at91-sama5d27_wlsom1.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "Microchip SAMA5D27 WLSOM1 EK";
++ compatible = "microchip,sama5d27-wlsom1-ek",
"microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
++
++ aliases {
++ serial0 = &uart0; /* DBGU */
++ serial1 = &uart6; /* BT */
++ serial2 = &uart5; /* mikro BUS 2 */
++ serial3 = &uart3; /* mikro BUS 1 */
++ i2c1 = &i2c1;
++ };
++
++ chosen {
++ stdout-path = "serial0:115200n8";
++ };
++
++ gpio_keys {
++ compatible = "gpio-keys";
++
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_key_gpio_default>;
++ status = "okay";
++
++ sw4 {
++ label = "USER BUTTON";
++ gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
++ linux,code = <KEY_PROG1>;
++ wakeup-source;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_led_gpio_default>;
++ status = "okay";
++
++ red {
++ label = "red";
++ gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
++ };
++
++ green {
++ label = "green";
++ gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
++ };
++
++ blue {
++ label = "blue";
++ gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "heartbeat";
++ };
++ };
++};
++
++&adc {
++ vddana-supply = <&vdd_3v3>;
++ vref-supply = <&vdd_3v3>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_adc_default>;
++ status = "okay";
++};
++
++&flx0 {
++ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
++ status = "okay";
++
++ uart5: serial@200 {
++ pinctrl-0 = <&pinctrl_flx0_default>;
++ pinctrl-names = "default";
++ atmel,use-dma-rx;
++ atmel,use-dma-tx;
++ status = "okay";
++ };
++};
++
++&flx1 {
++ status = "okay";
++
++ uart6: serial@200 {
++ atmel,use-dma-rx;
++ atmel,use-dma-tx;
++ status = "okay";
++ };
++};
++
++&macb0 {
++ status = "okay";
++};
++
++&pioA {
++ /*
++ * There is no real pinmux for ADC, if the pin
++ * is not requested by another peripheral then
++ * the muxing is done when channel is enabled.
++ * Requesting pins for ADC is GPIO is
++ * encouraged to prevent conflicts and to
++ * disable bias in order to be in the same
++ * state when the pin is not muxed to the adc.
++ */
++ pinctrl_adc_default: adc_default {
++ pinmux = <PIN_PD25__GPIO>,
++ <PIN_PD26__GPIO>;
++ bias-disable;
++ };
++
++ pinctrl_flx0_default: flx0_usart_default {
++ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
++ <PIN_PB29__FLEXCOM0_IO1>;
++ bias-disable;
++ };
++
++ pinctrl_key_gpio_default: key_gpio_default {
++ pinmux = <PIN_PB2__GPIO>;
++ bias-pull-up;
++ };
++
++ pinctrl_led_gpio_default: led_gpio_default {
++ pinmux = <PIN_PA6__GPIO>,
++ <PIN_PA7__GPIO>,
++ <PIN_PA8__GPIO>;
++ bias-pull-down;
++ };
++
++ pinctrl_sdmmc0_default: sdmmc0_default {
++ cmd_data {
++ pinmux = <PIN_PA1__SDMMC0_CMD>,
++ <PIN_PA2__SDMMC0_DAT0>,
++ <PIN_PA3__SDMMC0_DAT1>,
++ <PIN_PA4__SDMMC0_DAT2>,
++ <PIN_PA5__SDMMC0_DAT3>;
++ bias-disable;
++ };
++
++ ck_cd_vddsel {
++ pinmux = <PIN_PA0__SDMMC0_CK>,
++ <PIN_PA11__SDMMC0_VDDSEL>,
++ <PIN_PA12__SDMMC0_WP>,
++ <PIN_PA13__SDMMC0_CD>;
++ bias-disable;
++ };
++ };
++
++ pinctrl_uart0_default: uart0_default {
++ pinmux = <PIN_PB26__URXD0>,
++ <PIN_PB27__UTXD0>;
++ bias-disable;
++ };
++
++ pinctrl_uart3_default: uart3_default {
++ pinmux = <PIN_PB11__URXD3>,
++ <PIN_PB12__UTXD3>;
++ bias-disable;
++ };
++
++ pinctrl_pwm0_default: pwm0_default {
++ pinmux = <PIN_PA31__PWML0>,
++ <PIN_PA30__PWMH0>;
++ bias-disable;
++ };
++
++ pinctrl_usb_default: usb_default {
++ pinmux = <PIN_PA10__GPIO>;
++ bias-disable;
++ };
++
++ pinctrl_usba_vbus: usba_vbus {
++ pinmux = <PIN_PA16__GPIO>;
++ bias-disable;
++ };
++};
++
++&pwm0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_pwm0_default>;
++ status = "okay";
++};
++
++&qspi1 {
++ status = "okay";
++
++ qspi1_flash: spi_flash@0 {
++ status = "okay";
++ };
++};
++
++&sdmmc0 {
++ bus-width = <4>;
++ mmc-ddr-3_3v;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_sdmmc0_default>;
++ status = "okay";
++};
++
++&shutdown_controller {
++ atmel,shdwc-debouncer = <976>;
++ atmel,wakeup-rtc-timer;
++
++ input@0 {
++ reg = <0>;
++ };
++};
++
++&tcb0 {
++ timer0: timer@0 {
++ compatible = "atmel,tcb-timer";
++ reg = <0>;
++ };
++
++ timer1: timer@1 {
++ compatible = "atmel,tcb-timer";
++ reg = <1>;
++ };
++};
++
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_uart0_default>;
++ atmel,use-dma-rx;
++ atmel,use-dma-tx;
++ status = "okay";
++};
++
++&uart3 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_uart3_default>;
++ atmel,use-dma-rx;
++ atmel,use-dma-tx;
++ status = "okay";
++};
++
++&usb0 {
++ atmel,vbus-gpio = <&pioA PIN_PA16 GPIO_ACTIVE_HIGH>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_usba_vbus>;
++ status = "okay";
++};
++
++&usb1 {
++ num-ports = <3>;
++ atmel,vbus-gpio = <0
++ &pioA PIN_PA10 GPIO_ACTIVE_HIGH
++ 0
++ >;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_usb_default>;
++ status = "okay";
++};
++
++&usb2 {
++ phy_type = "hsic";
++ status = "okay";
++};
++
++&watchdog {
++ status = "okay";
++};
++
--
2.23.0
--- End Message ---
