#14938: Kernel 3.10.28 doesn't work - kirkwood
------------------------+----------------------------------
Reporter: anonymous | Owner: developers
Type: defect | Status: new
Priority: high | Milestone: Chaos Calmer (trunk)
Component: kernel | Version: Trunk
Resolution: | Keywords: kernel freez
------------------------+----------------------------------
Comment (by bittorf@…):
it boots!
hmmm, dont know what i have done - at least upgrade to kernel 3.14.17
and flashed bin/kirkwood/openwrt-kirkwood-goflexnet-uImage
(this is a goflex home - but it seems to work)
{{{
NAND read: device 0 offset 0x200000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 06400000 ...
Image Name: ARM OpenWrt Linux-3.14.17
Created: 2014-08-20 9:04:51 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1602835 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Using machid 0xd0a from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.17 ([email protected]) (gcc
version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42220) ) #2 Wed Aug 20
05:04:41 EDT 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE),
cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Seagate GoFlex Net
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200
mtdparts=orion_nand:1M(u-boot),1M@1M(second_stage_u-
boot),3M@2M(kernel),251M@5M(rootfs) rw root=/dev/mtdblock3 rw
rootfstype=jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Memory: 125240K/131072K available (3218K kernel code, 150K
rwdata, 912K rodata, 132K init, 181K bss, 5832K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0410d5c (4132 kB)
[ 0.000000] .init : 0xc0411000 - 0xc04323a4 ( 133 kB)
[ 0.000000] .data : 0xc0434000 - 0xc045992c ( 151 kB)
[ 0.000000] .bss : 0xc045992c - 0xc0486d78 ( 182 kB)
[ 0.000000] NR_IRQS:114
[ 0.000016] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every
21474836475ns
[ 0.000149] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090096] pid_max: default: 32768 minimum: 301
[ 0.090212] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090231] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.092439] CPU: Testing write buffer coherency: ok
[ 0.092763] Setting up static identity map for 0x11168 - 0x111a4
[ 0.094546] pinctrl core: initialized pinctrl subsystem
[ 0.095508] regulator-dummy: no parameters
[ 0.096000] NET: Registered protocol family 16
[ 0.096379] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.098952] cpuidle: using governor ladder
[ 0.099025] Kirkwood: MV88F6281-A1.
[ 0.099175] Feroceon L2: Enabling L2
[ 0.099215] Feroceon L2: Cache support initialised.
[ 0.099684] [Firmware Info]: /ocp@f1000000/ethernet-
controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.112445] bio: create slab <bio-0> at 0
[ 0.113043] USB Power: Failed to request enable GPIO29: -517
[ 0.113197] reg-fixed-voltage 1.regulator: Failed to register
regulator: -517
[ 0.113216] platform 1.regulator: Driver reg-fixed-voltage requests
probe deferral
[ 0.114029] SCSI subsystem initialized
[ 0.114813] usbcore: registered new interface driver usbfs
[ 0.114968] usbcore: registered new interface driver hub
[ 0.115141] usbcore: registered new device driver usb
[ 0.116617] Switched to clocksource orion_clocksource
[ 0.118463] NET: Registered protocol family 2
[ 0.119183] TCP established hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.119207] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.119226] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.119282] TCP: reno registered
[ 0.119294] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119315] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119481] NET: Registered protocol family 1
[ 0.120833] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.121323] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.121334] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.121546] msgmni has been set to 244
[ 0.122196] io scheduler noop registered
[ 0.122207] io scheduler deadline registered (default)
[ 0.123589] kirkwood-pinctrl f1010000.pinctrl: registered pinctrl
driver
[ 0.198211] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.199590] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 33,
base_baud = 12500000) is a 16550A
[ 0.594193] console [ttyS0] enabled
[ 0.599603] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xda
[ 0.605986] nand: Toshiba NAND 256MiB 3,3V 8-bit
[ 0.610644] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 0.616336] Scanning device for bad blocks
[ 0.834816] 4 cmdlinepart partitions found on MTD device orion_nand
[ 0.841126] Creating 4 MTD partitions on "orion_nand":
[ 0.846289] 0x000000000000-0x000000100000 : "u-boot"
[ 0.852366] 0x000000100000-0x000000200000 : "second_stage_u-boot"
[ 0.859431] 0x000000200000-0x000000500000 : "kernel"
[ 0.865321] 0x000000500000-0x000010000000 : "rootfs"
[ 0.871530] mtd: device 3 (rootfs) set to be root filesystem
[ 0.877334] mtdsplit: no squashfs found in "orion_nand"
[ 0.883208] libphy: orion_mdio_bus: probed
[ 0.888035] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version
1.4
[ 0.967579] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC
address 00:10:75:26:28:7d
[ 0.976457] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.983035] ehci-pci: EHCI PCI platform driver
[ 0.987653] ehci-platform: EHCI generic platform driver
[ 0.993086] ehci-orion: EHCI orion driver
[ 0.997233] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.002760] orion-ehci f1050000.ehci: new USB bus registered, assigned
bus number 1
[ 1.010563] orion-ehci f1050000.ehci: irq 24, io mem 0xf1050000
[ 1.026633] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.033405] hub 1-0:1.0: USB hub found
[ 1.037224] hub 1-0:1.0: 1 port detected
[ 1.041740] usbcore: registered new interface driver usb-storage
[ 1.051175] TCP: cubic registered
[ 1.054510] NET: Registered protocol family 17
[ 1.059258] 8021q: 802.1Q VLAN Support v1.8
[ 1.064475] regulator-dummy: disabling
[ 1.068699] USB Power: 5000 mV
[ 1.072287] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.079710] UBIFS error (pid 1): ubifs_mount: cannot open
"ubi0:rootfs", error -19
[ 1.570215] jffs2: Empty flash at 0x002001f8 ends at 0x00200800
[ 3.096834] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
[ 3.116661] VFS: Mounted root (jffs2 filesystem) on device 31:3.
[ 3.123090] Freeing unused kernel memory: 132K (c0411000 - c0432000)
procd: Console is alive
procd: - preinit -
[ 3.857298] random: mktemp urandom read with 2 bits of entropy
available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
mounting /dev/root
procd: - early -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 12.399260] device eth0 entered promiscuous mode
procd: - init complete -
[ 15.048092] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000
Mb/s, full duplex, flow control disabled
[ 15.058663] br-lan: port 1(eth0) entered forwarding state
[ 15.064114] br-lan: port 1(eth0) entered forwarding state
[ 17.056633] br-lan: port 1(eth0) entered forwarding state
^_procd: Instance odhcpd::instance1 s in a crash loop 6 crashes, 0 seconds
since last crash
BusyBox v1.22.1 (2014-08-19 09:57:00 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (Bleeding Edge, r42220)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
root@OpenWrt:/#
}}}
here is my (working) uboot-env:
{{{
GoFlexHome> printenv
baudrate=115200
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;
bootdelay=3
ethact=egiga0
ethaddr=00:10:75:2d:81:be
ipaddr=192.168.1.1
machid=0xd0a
serverip=192.168.1.2
stderr=serial
stdin=serial
stdout=serial
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),1M@1M
(second_stage_u-boot),3M@2M(kernel),251M@5M(rootfs) rw
x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
x_bootcmd_kernel=nand read 0x6400000 0x200000 0x300000
Environment size: 539/131068 bytes
}}}
--
Ticket URL: <https://dev.openwrt.org/ticket/14938#comment:5>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
