#14514: logread , procd report "Failed to connect to ubus"
------------------------+-----------------------------------
Reporter: anonymous | Owner: developers
Type: defect | Status: reopened
Priority: normal | Milestone: Barrier Breaker 14.07
Component: packages | Version: Trunk
Resolution: | Keywords:
------------------------+-----------------------------------
Changes (by lsoltero):
* status: closed => reopened
* resolution: no_response =>
Comment:
seeing the same issue on CC r42293
ubus seems to work fine once the system boots up and work.
root@Optimizer:~# ps w| grep ubus
406 root 892 S /sbin/ubusd
1141 root 1528 S /usr/sbin/uhttpd -f -h /www -r Optimizer -x
/cgi-bin -u /ubus -t 60 -T 30 -A 1 -n 3 -R -p 0.0.0.0:80 -i .
1740 root 1492 S grep ubus
root@Optimizer:~# ubus list
dhcp
hostapd.wlan0
log
network
network.device
network.interface
network.interface.lan
network.interface.loopback
network.interface.wan
network.interface.wan6
network.wireless
service
system
wondering why we are getting the mesg in the boot process and if there any
adverse effects...
here is the full bootlog. let me know if you need more info
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.10.49
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1074621 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1065bd
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (lsoltero@ubuntu) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42230) ) #81 Fri Aug 29 16:23:44 PDT 2014
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620a GEMINI
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize
32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,57600
rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Writing ErrCtl register=0001aef0
[ 0.000000] Readback ErrCtl register=0001aef0
[ 0.000000] Memory: 126552k/131072k available (2376k kernel code, 4520k
reserved, 589k data, 168k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered protocol family 16
[ 0.110000] bio: create slab <bio-0> at 0
[ 0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.140000] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.150000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.160000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.170000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] TCP established hash table entries: 1024 (order: 1, 8192
bytes)
[ 0.210000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.240000] TCP: reno registered
[ 0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] NET: Registered protocol family 1
[ 0.280000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.310000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.340000] msgmni has been set to 247
[ 0.350000] io scheduler noop registered
[ 0.350000] io scheduler deadline registered (default)
[ 0.360000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a
16550A
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.420000] 10000500.uart: ttyS1 at MMIO 0x10000500 (irq = 13) is a
16550A
[ 0.440000] m25p80 spi32766.0: mx25l12805d (16384 Kbytes)
[ 0.450000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.460000] Creating 4 MTD partitions on "spi32766.0":
[ 0.470000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.480000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.490000] 0x000000040000-0x000000050000 : "factory"
[ 0.500000] 0x000000050000-0x000001000000 : "firmware"
[ 0.520000] 0x0000001565fd-0x000001000000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.560000] mtd: partition "rootfs_data" created automatically,
ofs=0xa10000, len=0x5f0000
[ 0.580000] 0x000000a10000-0x000001000000 : "rootfs_data"
[ 0.590000] spi-rt2880 10000b00.spi: cs1 >= max 1
[ 0.600000] spi_master spi32766: spi_device register error
/palmbus@10000000/spi@b00/ve890@1
[ 0.620000] gsw: setting port4 to ephy mode
[ 0.630000] (unregistered net_device): port 4 link up (100Mbps/Full
duplex)
[ 0.650000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[ 0.660000] eth0: done loading
[ 0.670000] rt3xxx-usbphy usbphy.3: loaded
[ 0.680000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.690000] TCP: cubic registered
[ 0.690000] NET: Registered protocol family 17
[ 0.700000] 8021q: 802.1Q VLAN Support v1.8
[ 0.720000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 0.740000] Freeing unused kernel memory: 168K (802e6000 - 80310000)
procd: Console is alive
procd: - watchdog -
[ 5.830000] usbcore: registered new interface driver usbfs
[ 5.840000] usbcore: registered new interface driver hub
[ 5.850000] usbcore: registered new device driver usb
[ 5.900000] SCSI subsystem initialized
[ 5.920000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.930000] ehci-platform: EHCI generic platform driver
[ 6.140000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 6.150000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 6.160000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.170000] ehci-platform 101c0000.ehci: new USB bus registered,
assigned bus number 1
[ 6.190000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.220000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.230000] hub 1-0:1.0: USB hub found
[ 6.240000] hub 1-0:1.0: 1 port detected
[ 6.250000] ehci-pci: EHCI PCI platform driver
[ 6.260000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.270000] ohci-platform 101c1000.ohci: Generic Platform OHCI
Controller
[ 6.280000] ohci-platform 101c1000.ohci: new USB bus registered,
assigned bus number 2
[ 6.300000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.370000] hub 2-0:1.0: USB hub found
[ 6.380000] hub 2-0:1.0: 1 port detected
[ 6.390000] leds-gpio gpio-leds.4: pins are not configured from the
driver
[ 6.420000] sdhci: Secure Digital Host Controller Interface driver
[ 6.430000] sdhci: Copyright(c) Pierre Ossman
[ 6.440000] MTK MSDC device init.
[ 6.490000] mtk-sd: MediaTek MT6575 MSDC Driver
[ 6.500000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 6.520000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 6.610000] mmc0: new high speed SDHC card at address e624
[ 6.640000] mmcblk0: mmc0:e624 SL08G 7.40 GiB
[ 6.660000] mmcblk0: p1 p2
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
kmod: ran 1 iterations
[ 10.990000] jffs2_scan_eraseblock(): End of filesystem marker found at
0x10000
[ 11.000000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 11.010000] jffs2_build_filesystem(): erasing all blocks after the end
marker... done.
[ 42.460000] jffs2: notice: (344) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
block: extroot: failed to load /tmp/jffs_cfg/etc/config/fstab: Entry not
found
jffs2 is ready
jffs2 is ready
[ 42.620000] jffs2: notice: (341) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
switching to overlay
- config restore -
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Failed to connect to ubus
Please press Enter to activate this console.
[ 44.600000] Adding 500164k swap on /dev/mmcblk0p1. Priority:-1
extents:1 across:500164k SS
[ 46.470000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
mode. Opts:
[ 46.730000] NET: Registered protocol family 10
[ 46.840000] tty0tty null modem driver v1.0
[ 46.860000] nf_conntrack version 0.5.0 (1980 buckets, 7920 max)
[ 46.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 46.950000] usbcore: registered new interface driver cdc_acm
[ 46.960000] cdc_acm: USB Abstract Control Model driver for USB modems
and ISDN adapters
[ 46.990000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 47.000000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 47.030000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.090000] usbcore: registered new interface driver ums-alauda
[ 47.110000] usbcore: registered new interface driver ums-cypress
[ 47.140000] usbcore: registered new interface driver ums-datafab
[ 47.160000] usbcore: registered new interface driver ums-freecom
[ 47.180000] usbcore: registered new interface driver ums-isd200
[ 47.200000] usbcore: registered new interface driver ums-jumpshot
[ 47.220000] usbcore: registered new interface driver ums-karma
[ 47.240000] usbcore: registered new interface driver ums-sddr09
[ 47.250000] usbcore: registered new interface driver ums-sddr55
[ 47.270000] usbcore: registered new interface driver ums-usbat
[ 47.290000] usbcore: registered new interface driver usbserial
[ 47.300000] usbcore: registered new interface driver usbserial_generic
[ 47.310000] usbserial: USB Serial support registered for generic
[ 47.340000] xt_time: kernel timezone is -0000
[ 47.390000] cfg80211: Calling CRDA to update world regulatory domain
[ 47.400000] usbcore: registered new interface driver ftdi_sio
[ 47.410000] cfg80211: World regulatory domain updated:
[ 47.420000] cfg80211: DFS Master region: unset
[ 47.430000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 47.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.470000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.480000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.500000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.520000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 47.530000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 47.550000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.560000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 47.580000] usbserial: USB Serial support registered for FTDI USB
Serial Device
[ 47.640000] usbcore: registered new interface driver pl2303
[ 47.660000] usbserial: USB Serial support registered for pl2303
[ 47.670000] PPP generic driver version 2.4.2
[ 47.680000] NET: Registered protocol family 24
[ 47.720000] usbcore: registered new interface driver snd-usb-audio
[ 47.740000] usbcore: registered new interface driver ipw
[ 47.750000] usbserial: USB Serial support registered for IPWireless
converter
[ 47.760000] usbcore: registered new interface driver option
[ 47.780000] usbserial: USB Serial support registered for GSM modem
(1-port)
[ 47.810000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev
0500 detected
[ 47.830000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620
detected
[ 55.560000] device eth0.2 entered promiscuous mode
[ 55.570000] device eth0 entered promiscuous mode
[ 55.600000] br-lan: port 1(eth0.2) entered forwarding state
[ 55.610000] br-lan: port 1(eth0.2) entered forwarding state
[ 57.610000] br-lan: port 1(eth0.2) entered forwarding state
[ 58.350000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 58.380000] device wlan0 entered promiscuous mode
[ 58.460000] br-lan: port 2(wlan0) entered forwarding state
[ 58.470000] br-lan: port 2(wlan0) entered forwarding state
[ 58.480000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 60.470000] br-lan: port 2(wlan0) entered forwarding state
procd: - init complete -
Optimizer login:
--
Ticket URL: <https://dev.openwrt.org/ticket/14514#comment:5>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
openwrt-tickets@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
