#17556: mt7620n kernel 3.10
---------------------------------+-------------------------------------
Reporter: guozhengqian0825@… | Owner: developers
Type: defect | Status: new
Priority: high | Milestone: Barrier Breaker 14.07
Component: other | Version: Trunk
Resolution: | Keywords: mt7620n wireless driver
---------------------------------+-------------------------------------
Comment (by weeds):
Dear, most of the information is at below, please let me know if you have
any other thought.
root@weeds:~# dmesg
[ 0.000000] Linux version 3.10.49 (weeds@weeds-Lenovo) (gcc version
4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r2) ) #19 Thu Jul 24 03:36:56 EDT
2014
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Zbtlink ZBT-WA05
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802b2990, node_mem_map
81003e00
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize
32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200
rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=0002e23b
[ 0.000000] Readback ErrCtl register=0002e23b
[ 0.000000] Memory: 61648k/65536k available (2295k kernel code, 3888k
reserved, 552k data, 220k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] rt2880-pinmux pinctrl.1: try to register 73 pins ...
[ 0.080000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux
[ 0.080000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux
[ 0.080000] pinctrl core: add 3 pinmux maps
[ 0.080000] rt2880-pinmux pinctrl.1: found group selector 0 for i2c
[ 0.080000] rt2880-pinmux pinctrl.1: found group selector 7 for spi
refclk
[ 0.080000] rt2880-pinmux pinctrl.1: found group selector 11 for wled
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 2 (io2) for pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 37 (io37) for
pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for
pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for
pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for
pinctrl.1
[ 0.080000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.110000] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.110000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.120000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.120000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.130000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.130000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.140000] Switching to clocksource MIPS
[ 0.150000] NET: Registered protocol family 2
[ 0.150000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.150000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.160000] TCP: Hash tables configured (established 512 bind 512)
[ 0.160000] TCP: reno registered
[ 0.170000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.170000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] NET: Registered protocol family 1
[ 0.180000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.190000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[ 0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.210000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.220000] msgmni has been set to 120
[ 0.220000] io scheduler noop registered
[ 0.230000] io scheduler deadline registered (default)
[ 0.230000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.240000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.240000] pinctrl core: add 1 pinmux maps
[ 0.240000] rt2880-pinmux pinctrl.1: found group selector 3 for
uartlite
[ 0.240000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for
10000c00.uartlite
[ 0.240000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for
10000c00.uartlite
[ 0.240000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a
16550A
[ 0.250000] console [ttyS0] enabled, bootconsole disabled
[ 0.260000] pinctrl core: add 1 pinmux maps
[ 0.260000] rt2880-pinmux pinctrl.1: found group selector 2 for spi
[ 0.260000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for
10000b00.spi
[ 0.260000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for
10000b00.spi
[ 0.260000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for
10000b00.spi
[ 0.260000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for
10000b00.spi
[ 0.260000] m25p80 spi32766.0: found w25q128, expected w25q64
[ 0.270000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.280000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.280000] Creating 4 MTD partitions on "spi32766.0":
[ 0.290000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.290000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.300000] 0x000000040000-0x000000050000 : "factory"
[ 0.310000] 0x000000050000-0x000001000000 : "firmware"
[ 0.320000] 0x00000014940c-0x000001000000 : "rootfs"
[ 0.320000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.330000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.340000] mtd: partition "rootfs_data" created automatically,
ofs=0x4a0000, len=0xb60000
[ 0.350000] 0x0000004a0000-0x000001000000 : "rootfs_data"
[ 0.360000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[ 0.370000] eth0: done loading
[ 0.370000] rt3xxx-usbphy ubsphy.3: loaded
[ 0.380000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.380000] TCP: cubic registered
[ 0.380000] NET: Registered protocol family 17
[ 0.390000] 8021q: 802.1Q VLAN Support v1.8
[ 0.410000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 0.410000] Freeing unused kernel memory: 220K (802c9000 - 80300000)
[ 3.980000] usbcore: registered new interface driver usbfs
[ 3.980000] usbcore: registered new interface driver hub
[ 3.990000] usbcore: registered new device driver usb
[ 4.000000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pio:1
[ 4.000000] leds-gpio gpio-leds.4: pins are not configured from the
driver
[ 4.010000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for pio:38
[ 4.010000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for pio:39
[ 4.010000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pio:72
[ 7.930000] jffs2: notice: (275) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 16 of
xref (0 dead, 2 orphan) found.
[ 9.780000] NET: Registered protocol family 10
[ 9.810000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[ 9.830000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.880000] u32 classifier
[ 9.880000] input device check on
[ 9.880000] Actions configured
[ 9.900000] Mirror/redirect action on
[ 9.910000] Failed to load ipt action
[ 9.970000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 9.970000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 9.990000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.090000] xt_time: kernel timezone is -0000
[ 10.150000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.150000] cfg80211: World regulatory domain updated:
[ 10.160000] cfg80211: DFS Master region: unset
[ 10.160000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.170000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.180000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.190000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.210000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.210000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.220000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.230000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 10.260000] PPP generic driver version 2.4.2
[ 10.270000] NET: Registered protocol family 24
[ 10.310000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev
0500 detected
[ 10.320000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620
detected
[ 10.330000] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 17.670000] device eth0.1 entered promiscuous mode
[ 17.680000] device eth0 entered promiscuous mode
[ 17.690000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.690000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.760000] device eth0.3 entered promiscuous mode
[ 17.760000] br-lan2: port 1(eth0.3) entered forwarding state
[ 17.770000] br-lan2: port 1(eth0.3) entered forwarding state
[ 19.690000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.770000] br-lan2: port 1(eth0.3) entered forwarding state
[ 20.670000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.670000] device wlan0 entered promiscuous mode
[ 20.680000] br-lan: port 2(wlan0) entered forwarding state
[ 20.680000] br-lan: port 2(wlan0) entered forwarding state
[ 20.770000] device wlan0-1 entered promiscuous mode
[ 20.780000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 20.780000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 20.790000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 20.820000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 20.820000] br-lan2: port 2(wlan0-1) entered disabled state
[ 21.490000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 21.500000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 21.500000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 21.540000] ------------[ cut here ]------------
[ 21.540000] WARNING: at /home/weeds/work/openwrt_mt7620n/build_dir
/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux-ramips_mt7620n/compat-
wireless-2014-05-22/drivers/net/wireless/rt2x00/rt2800lib.c:1092
rt2800_conf_tx+0x3c8/0x494 [rt2800lib]()
[ 21.560000] Modules linked in: rt2800soc rt2800mmio rt2800lib pppoe
ppp_async iptable_nat rt2x00soc rt2x00mmio rt2x00lib pppox ppp_generic
nf_nat_ipv4 nf_conntrack_ipv4 mac80211 ipt_MASQUERADE cfg80211 xt_time
xt_tcpudp xt_tcpmss xt_string xt_statistic xt_state xt_recent xt_quota
xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length
xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit
xt_connbytes xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_NETMAP xt_LOG
xt_HL xt_DSCP xt_CT xt_CLASSIFY ts_kmp ts_fsm ts_bm slhc nf_nat_irc
nf_nat_ftp nf_nat nf_defrag_ipv4 nf_conntrack_irc nf_conntrack_ftp
iptable_raw iptable_mangle iptable_filter ipt_REJECT ipt_ECN ip_tables
crc_itu_t crc_ccitt compat sch_teql sch_tbf sch_sfq sch_red sch_prio
sch_htb sch_gred sch_dsmark sch_codel em_text em_nbyte em_meta em_cmp
cls_basic act_police act_ipt act_connmark act_skbedit act_mirred em_u32
cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_hfsc sch_ingress
ledtrig_usbdev ip6t_REJECT ip6table_raw ip6table_mangle ip6table_filter
ip6_tables x_tables nf_conntrack_ipv6 nf_conntrack nf_defrag_ipv6 ifb ipv6
eeprom_93cx6 arc4 crypto_blkcipher leds_gpio dwc2_platform dwc2
gpio_button_hotplug usbcore nls_base usb_common
[ 21.680000] CPU: 0 PID: 1233 Comm: uci Not tainted 3.10.49 #19
[ 21.680000] Stack : 00000000 00000000 00000000 00000000 80302eea
00000032 8336e758 8318f340
[ 21.680000] 80269d18 802b31fb 000004d1 80302694 8336e758 8318f340
00000008 0000001c
[ 21.680000] 00000001 8001e1c0 00000003 8001bc2c 831b3bd8 8318f340
8026b5a4 8332ba4c
[ 21.680000] 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
[ 21.680000] 00000000 00000000 00000000 00000000 00000000 00000000
00000000 8332b9d8
[ 21.680000] ...
[ 21.720000] Call Trace:
[ 21.720000] [<800112f4>] show_stack+0x48/0x70
[ 21.730000] [<8001bd28>] warn_slowpath_common+0x78/0xa8
[ 21.730000] [<8001bde0>] warn_slowpath_null+0x18/0x24
[ 21.740000] [<831a4078>] rt2800_conf_tx+0x3c8/0x494 [rt2800lib]
[ 21.740000]
[ 21.740000] ---[ end trace 15126d46dc8dcb3b ]---
[ 22.680000] br-lan: port 2(wlan0) entered forwarding state
[ 23.500000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 324.610000] raw_sendmsg: wifidog forgot to set AF_INET. Fix it!
[ 686.140000] HTB: quantum of class 10001 is big. Consider r2q change.
[ 686.160000] HTB: quantum of class 11024 is big. Consider r2q change.
[ 686.220000] HTB: quantum of class 10001 is big. Consider r2q change.
[ 686.240000] HTB: quantum of class 11024 is big. Consider r2q change.
[156408.390000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[156408.400000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[156408.410000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[156408.420000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[156408.430000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.720000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.730000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.740000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.750000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.760000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.930000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.940000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.950000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.960000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158359.970000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error -
Dropping frame due to full tx queue 2
[158810.310000] eth0: port 0 link up (100Mbps/Full duplex)
--
Ticket URL: <https://dev.openwrt.org/ticket/17556#comment:3>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
