#18742: WRTnode freezes while booting just after wifi interface is started
-------------------------------+-----------------------------------
Reporter: bonenkamp@… | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone:
Component: base system | Version: Barrier Breaker 14.07
Keywords: freeze crash wifi |
-------------------------------+-----------------------------------
U-Boot 1.1.3 (Nov 27 2014 - 11:11:12)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
GPIO init
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128BV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Nov 27 2014 Time:11:11:12
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
raspi_read: from:40028 len:6
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.10.49
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1033567 Bytes = 1009.3 kB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:fc55f
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (devuser@ws-devhost) (gcc version
4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43889) ) #2 Mon Jan 12 21:16:05 CET
2015
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is WRTNODE
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize
32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200
rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=0000400b
[ 0.000000] Readback ErrCtl register=0000400b
[ 0.000000] Memory: 61652k/65536k available (2296k kernel code, 3884k
reserved, 560k data, 212k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.110000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.110000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.120000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.120000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.130000] Switching to clocksource MIPS
[ 0.140000] NET: Registered protocol family 2
[ 0.140000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.140000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.150000] TCP: Hash tables configured (established 512 bind 512)
[ 0.150000] TCP: reno registered
[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.160000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.170000] NET: Registered protocol family 1
[ 0.170000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.190000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.200000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.210000] msgmni has been set to 120
[ 0.220000] io scheduler noop registered
[ 0.220000] io scheduler deadline registered (default)
[ 0.230000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.230000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a
16550A
[ 0.240000] console [ttyS0] enabled, bootconsole disabled
[ 0.240000] console [ttyS0] enabled, bootconsole disabled
[ 0.260000] m25p80 spi32766.0: found w25q128, expected mx25l12805d
[ 0.260000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.270000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.270000] Creating 4 MTD partitions on "spi32766.0":
[ 0.280000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.290000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.290000] 0x000000040000-0x000000050000 : "factory"
[ 0.300000] 0x000000050000-0x000001000000 : "firmware"
[ 0.310000] 0x00000014c59f-0x000001000000 : "rootfs"
[ 0.310000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.330000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.330000] mtd: partition "rootfs_data" created automatically,
ofs=0x390000, len=0xc70000
[ 0.340000] 0x000000390000-0x000001000000 : "rootfs_data"
[ 0.350000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.360000] ralink_soc_eth 10100000.ethernet eth0: ralink at
0xb0100000, irq 5
[ 0.370000] rt3xxx-usbphy usbphy.3: loaded
[ 0.370000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.380000] TCP: cubic registered
[ 0.380000] NET: Registered protocol family 17
[ 0.390000] 8021q: 802.1Q VLAN Support v1.8
[ 0.400000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 0.410000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
[ 4.210000] usbcore: registered new interface driver usbfs
[ 4.220000] usbcore: registered new interface driver hub
[ 4.230000] usbcore: registered new device driver usb
[ 4.240000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.240000] ehci-platform: EHCI generic platform driver
[ 4.450000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 4.460000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 4.460000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.470000] ehci-platform 101c0000.ehci: new USB bus registered,
assigned bus number 1
[ 4.480000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.500000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.500000] hub 1-0:1.0: USB hub found
[ 4.510000] hub 1-0:1.0: 1 port detected
[ 4.510000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.520000] ohci-platform 101c1000.ohci: Generic Platform OHCI
Controller
[ 4.530000] ohci-platform 101c1000.ohci: new USB bus registered,
assigned bus number 2
[ 4.530000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.600000] hub 2-0:1.0: USB hub found
[ 4.600000] hub 2-0:1.0: 1 port detected
[ 4.610000] leds-gpio gpio-leds.4: pins are not configured from the
driver
[ 4.620000] platform gpio-leds.4: Driver leds-gpio requests probe
deferral
procd: - preinit -
[ 4.870000] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
jffs2 is ready
jffs2 is ready
[ 8.240000] jffs2: notice: (281) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of
xref (0 dead, 0 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 9.640000] NET: Registered protocol family 10
[ 9.690000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[ 9.700000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.720000] cm109: Keymap for Komunikate KIP1000 phone loaded
[ 9.730000] usbcore: registered new interface driver cm109
[ 9.730000] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad
[ 9.740000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 9.750000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 9.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.810000] xt_time: kernel timezone is -0000
[ 9.840000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.840000] cfg80211: World regulatory domain updated:
[ 9.850000] cfg80211: DFS Master region: unset
[ 9.850000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 9.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 9.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 9.890000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 9.900000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 9.900000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 9.910000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 9.920000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 9.980000] PPP generic driver version 2.4.2
[ 9.990000] NET: Registered protocol family 24
[ 10.010000] usbcore: registered new interface driver snd-usb-audio
[ 10.040000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev
0500 detected
[ 10.050000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620
detected
[ 10.060000] leds-gpio gpio-leds.4: pins are not configured from the
driver
[ 10.070000] platform gpio-leds.4: Driver leds-gpio requests probe
deferral
procd: - init complete -
[ 17.130000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 17.150000] 8021q: adding VLAN 0 to HW filter on device eth0
[ 17.150000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.190000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 17.200000] device eth0.1 entered promiscuous mode
[ 17.210000] device eth0 entered promiscuous mode
[ 17.240000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 17.820000] cfg80211: Calling CRDA for country: DE
[ 17.840000] cfg80211: Regulatory domain changed to country: DE
[ 17.840000] cfg80211: DFS Master region: ETSI
[ 17.850000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 17.860000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 17.860000] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 17.870000] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz), (N/A,
2000 mBm), (0 s)
[ 17.880000] cfg80211: (5470000 KHz - 5725000 KHz @ 80000 KHz), (N/A,
2700 mBm), (0 s)
[ 17.890000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 18.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.870000] br-lan: port 1(eth0.1) entered forwarding state
[ 18.880000] br-lan: port 1(eth0.1) entered forwarding state
[ 18.880000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 18.890000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 18.910000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
---> this is the very last output while booting up and the blue led -
which is const on while booting - goes to OFF.
The firmware is a self-compiled openwrt r43889 trying to startup wifi to
connect in mode 'sta' to my home network. But this freeze/crash (sometimes
triggering a instant reboot) happen in mode 'ap' too. It is also
reproducible with the lastest image available at the wrtnode wiki.
Unfortunate I've only one wrtnode, so no chance to rule out any potential
hardware problem...
As the image is self compiled I can apply any suggested config/source
change on request and will continue to investigate this problem by
myself...
Thanks in advance!
Ralf
--
Ticket URL: <https://dev.openwrt.org/ticket/18742>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
