#19167: ath10k firmware crashed after r44655
--------------------+----------------------------------
 Reporter:  gcyscm  |      Owner:  developers
     Type:  defect  |     Status:  new
 Priority:  normal  |  Milestone:  Chaos Calmer (trunk)
Component:  kernel  |    Version:  Trunk
 Keywords:          |
--------------------+----------------------------------
 [   25.040000] cfg80211:   (start_freq - end_freq @ bandwidth),
 (max_antenna_gain, max_eirp), (dfs_cac_time)
 [   25.050000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
 3000 mBm), (N/A)
 [   25.060000] cfg80211:   (5270000 KHz - 5330000 KHz @ 40000 KHz), (N/A,
 1700 mBm), (0 s)
 [   25.070000] cfg80211:   (5490000 KHz - 5590000 KHz @ 80000 KHz), (N/A,
 3000 mBm), (0 s)
 [   25.080000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (N/A,
 3000 mBm), (0 s)
 [   25.080000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
 3000 mBm), (N/A)
 [   25.670000] eth0: link up (1000Mbps/Full duplex)
 [   25.670000] br-lan: port 1(eth0) entered forwarding state
 [   25.680000] br-lan: port 1(eth0) entered forwarding state
 [   26.420000] eth1: link up (100Mbps/Full duplex)
 [   27.680000] br-lan: port 1(eth0) entered forwarding state
 [   28.200000] ath10k_pci 0000:00:00.0: otp stream is empty, using
 board.bin contents
 [   30.390000] pppoe-wan: renamed from ppp0
 [   30.450000] device wlan0 entered promiscuous mode
 [   30.530000] device wlan1 entered promiscuous mode
 [   30.530000] br-lan: port 3(wlan1) entered forwarding state
 [   30.540000] br-lan: port 3(wlan1) entered forwarding state
 [   31.400000] br-lan: port 3(wlan1) entered disabled state
 [   31.510000] br-lan: port 3(wlan1) entered forwarding state
 [   31.510000] br-lan: port 3(wlan1) entered forwarding state
 [   33.510000] br-lan: port 3(wlan1) entered forwarding state
 [   33.590000] br-lan: port 2(wlan0) entered forwarding state
 [   33.600000] br-lan: port 2(wlan0) entered forwarding state
 [   34.020000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
 ba433228-96f6-4a42-9db4-21adc0528f79)
 [   34.030000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   34.040000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   34.060000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   34.070000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   34.080000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   34.180000] ieee80211 phy0: Hardware restart was requested
 [   34.180000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   34.190000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143
 [   34.200000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
 [   34.430000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   34.440000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   34.560000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   34.570000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   35.600000] br-lan: port 2(wlan0) entered forwarding state
 [   36.860000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   37.200000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
 cc53fd38-a6b1-41e1-9d76-819d19103f07)
 [   37.210000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   37.220000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   37.240000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   37.350000] ieee80211 phy0: Hardware restart was requested
 [   39.970000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   40.440000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid e9c5a12b-
 c0c5-4da7-809b-5995d3ffa25a)
 [   40.450000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   40.460000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   40.480000] ath10k_warn: 15 callbacks suppressed
 [   40.490000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   40.490000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   40.500000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   40.680000] ieee80211 phy0: Hardware restart was requested
 [   40.680000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   40.690000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143
 [   40.700000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
 [   40.920000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   40.930000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   41.060000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   41.070000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   41.260000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   43.650000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   43.940000] random: nonblocking pool is initialized
 [   44.010000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid d1b2ec10
 -5a3b-4d71-b4cd-aca93a1b4547)
 [   44.020000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   44.030000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   44.050000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   44.160000] ieee80211 phy0: Hardware restart was requested
 [   47.150000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   47.530000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
 dc710121-4db4-4ae4-91a1-94f0b6531886)
 [   47.540000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   47.550000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   47.570000] ath10k_warn: 14 callbacks suppressed
 [   47.580000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   47.580000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   47.590000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   47.700000] ieee80211 phy0: Hardware restart was requested
 [   47.700000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   47.710000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143
 [   47.720000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
 [   47.940000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   47.950000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   48.060000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   48.070000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   48.180000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   50.370000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   50.730000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 3aa511ea-
 25cd-4f5d-bcba-985c7b52b244)
 [   50.740000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   50.750000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   50.770000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   50.880000] ieee80211 phy0: Hardware restart was requested
 [   53.490000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   53.870000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 7020cc3a-
 6be9-4a51-9b73-73ba422b16a2)
 [   53.880000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   53.890000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   53.910000] ath10k_warn: 14 callbacks suppressed
 [   53.920000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   53.920000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   53.930000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   54.040000] ieee80211 phy0: Hardware restart was requested
 [   54.040000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   54.050000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143
 [   54.060000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
 [   54.280000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   54.290000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   54.400000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   54.410000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   54.520000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   56.710000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   57.090000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 92170570
 -5b3e-44c3-8921-3535e28e3b17)
 [   57.100000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   57.110000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   57.130000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   57.240000] ieee80211 phy0: Hardware restart was requested
 [   59.850000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   60.230000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
 9aba74da-8779-4203-8f99-d9c80dbba96e)
 [   60.240000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   60.250000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   60.270000] ath10k_warn: 14 callbacks suppressed
 [   60.280000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   60.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   60.290000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   60.400000] ieee80211 phy0: Hardware restart was requested
 [   60.400000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   60.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143
 [   60.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
 [   60.640000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   60.650000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   60.760000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   60.770000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
 [   60.880000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100800: -16
 [   63.070000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   63.450000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
 cb8661d8-f087-43fb-9f65-e153ab8f13f5)
 [   63.460000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   63.470000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   63.490000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   63.600000] ieee80211 phy0: Hardware restart was requested
 [   66.210000] ath10k_pci 0000:00:00.0: device successfully recovered
 [   66.590000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid c14c52c7
 -4eaf-48ca-a146-573ed466dbda)
 [   66.600000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
 [   66.610000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1
 testmode 1
 [   66.630000] ath10k_warn: 14 callbacks suppressed
 [   66.640000] ath10k_pci 0000:00:00.0: failed to read diag value at
 0x10100804: -16
 [   66.640000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address
 for firmware address 4: -16
 [   66.650000] ath10k_pci 0000:00:00.0: failed to read firmware dump area:
 -16
 [   66.760000] ieee80211 phy0: Hardware restart was requested
 [   66.760000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev
 1 stop: -143
 [   66.770000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev
 1 stop: -143

--
Ticket URL: <https://dev.openwrt.org/ticket/19167>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets

Reply via email to