Hi Lorenzo, I have some comments below
On 12/22/23 10:47, Lorenzo Bianconi wrote:
Introduce a dedicated test for garp-max-timeout knob Signed-off-by: Lorenzo Bianconi <lorenzo.bianc...@redhat.com> --- tests/ovn.at | 69 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 69 insertions(+) diff --git a/tests/ovn.at b/tests/ovn.at index 918f97a9e..deeb2a201 100644 --- a/tests/ovn.at +++ b/tests/ovn.at @@ -37464,3 +37464,72 @@ wait_for_ports_up OVN_CLEANUP([hv1]) AT_CLEANUP ]) + +OVN_FOR_EACH_NORTHD([ +AT_SETUP([gratuitous arp max timeout]) +AT_KEYWORDS([garp-timeout]) +TAG_UNSTABLE +AT_SKIP_IF([test $HAVE_TCPDUMP = no])
Since this test uses fmt_pkt(), you'll also need to skip the test if $HAVE_SCAPY = no .
+ovn_start + +check ovn-nbctl ls-add ls0 +check ovn-nbctl lr-add lr0 +check ovn-nbctl lrp-add lr0 lr0-ls0 f0:00:00:00:00:01 192.168.0.1/24 +check ovn-nbctl lsp-add ls0 ls0-lr0 -- set Logical_Switch_Port ls0-lr0 \ + type=router options:router-port=lr0-ls0 addresses='"f0:00:00:00:00:01"' + +check ovn-nbctl lsp-add ls0 ln_port +check ovn-nbctl lsp-set-addresses ln_port unknown +check ovn-nbctl lsp-set-type ln_port localnet +check ovn-nbctl --wait=hv lsp-set-options ln_port network_name=physnet1 + +# Prepare packets +echo $(fmt_pkt "Ether(dst='ff:ff:ff:ff:ff:ff', src='f0:00:00:00:00:01')/ \ + ARP(op=2, hwsrc='f0:00:00:00:00:01', hwdst='00:00:00:00:00:00', psrc='192.168.0.1', pdst='192.168.0.1')") > arp_expected
the arp_expected packet is never referenced after this point. This can either be removed (and you can therefore ignore my comment earlier about needing to check for HAVE_SCAPY), or you need to check the pcaps for accuracy using arp_expected.
+ +net_add n1 +sim_add hv1 +as hv1 +check ovs-vsctl \ + -- add-br br-phys \ + -- add-br br-eth0 + +ovn_attach n1 br-phys 192.168.0.10 + +AT_CHECK([ovs-vsctl set Open_vSwitch . external-ids:ovn-bridge-mappings=physnet1:br-eth0]) +AT_CHECK([ovs-vsctl add-port br-eth0 snoopvif -- set Interface snoopvif options:tx_pcap=hv1/snoopvif-tx.pcap options:rxq_pcap=hv1/snoopvif-rx.pcap]) + +# set garp max timeout to 2s +AT_CHECK([as hv1 ovs-vsctl set Open_vSwitch . external-ids:garp-max-timeout-sec=2]) + +# Wait until the patch ports are created in hv1 to connect br-int to br-eth0 +AT_CHECK([ovn-nbctl set logical_router lr0 options:chassis=hv1]) +OVN_WAIT_PATCH_PORT_FLOWS(["ln_port"], ["hv1"]) + +# sleep for 20s to get a garp every ~ 2s +sleep 22
I understand why the sleeps are here, but maybe you could sleep for less time and check for fewer packets to arrive? This way you still are testing the garp-max-timeout but the test won't take as long to run.
And if you really do need a total of ~34 seconds of sleeping, then I think this test should have AT_KEYWORDS[slowtest].
+ +n_arp=$(tcpdump -ner hv1/snoopvif-tx.pcap arp | wc -l) +AT_CHECK([test $n_arp -ge 10 -a $n_arp -lt 15]) + +# Temporarily remove lr0 chassis +# Wait for hv confirmation to make sure chassis is removed before we reset pcap +# Otherwise a garp might be sent after pcap have been reset but before chassis is removed +AT_CHECK([ovn-nbctl --wait=hv remove logical_router lr0 options chassis]) + +as hv1 reset_pcap_file snoopvif hv1/snoopvif +# set garp max timeout to 1s +AT_CHECK([as hv1 ovs-vsctl set Open_vSwitch . external-ids:garp-max-timeout-sec=1]) +hv1_uuid=$(ovn-sbctl --bare --columns _uuid list chassis hv1)
hv1_uuid is never used. You can probably remove this line.
+AT_CHECK([ovn-nbctl set logical_router lr0 options:chassis=hv1]) + +# sleep for 12s to get a garp every ~ 1s +sleep 12
Same comment about the sleep here: you can probably sleep for less time and check for fewer packets.
+ +n_arp=$(tcpdump -ner hv1/snoopvif-tx.pcap arp | wc -l) +AT_CHECK([test $n_arp -ge 10 -a $n_arp -lt 15]) + +OVN_CLEANUP([hv1]) + +AT_CLEANUP +])
_______________________________________________ dev mailing list d...@openvswitch.org https://mail.openvswitch.org/mailman/listinfo/ovs-dev