*Hi Jan,** ** **Here is the requested info:* *systemctl show owserver.service|grep ExecStart*
ExecStart={ path=/usr/bin/owserver ; argv[]=/usr/bin/owserver -c
/etc/owfs.conf ; ignore_errors=no ; start_time=[Mon 2020-05-04 17:17:17
EDT] ; stop_time=[Mon 2020-05-04 17:17:17 EDT] ; pid=485 ; code=exited ;
status=0 }
*I'm not sure how to tell what adapter I'm using (not a hardware guy)
but I think I was told it is DS2480 as the busmaster and the device is
DS2413.*
*cat /boot/config.txt*
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if
console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's
size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio
work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference,
blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
#dtoverlay=w1-gpio,gpiopin=20
# NOOBS Auto-generated Settings:
#hdmi_force_hotplug=1
On 5/3/2020 9:52 PM, Jan Kandziora wrote:
> Am 03.05.20 um 23:55 schrieb Dennis Putnam:
>> I've installed owfs on my Pi4 but cannot start owserver. I get the
>> following in journalctl:
>>
>> -- Defined-By: systemd -- Support: https://www.debian.org/support
>>
>> [...]
>>
> That log is not too helpful. We need the output of
>
> $ systemctl show owserver.service|grep ExecStart
> $ cat /etc/owfs.conf
>
> Also, we need to know what Onewire hostadapter you use. Is it the
> bitbanging host on GPIO4? Is it an I²C connected DS2482 or similar? If
> yes, also show us
>
> $ cat /boot/config.txt
>
> Kind regards
>
> Jan
>
>
> _______________________________________________
> Owfs-developers mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/owfs-developers
signature.asc
Description: OpenPGP digital signature
_______________________________________________ Owfs-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/owfs-developers
