Hi, thank you for the quick answers. I thought I would need to edit the corosync.conf file. So I do not need to? Where should I configure the heartbeat interconnect interfaces?
With corosync-cfgtool -s it shows the wrong ip? But where does that come from? Andreas Von: emmanuel segura [mailto:emi2f...@gmail.com] Gesendet: Montag, 9. Dezember 2013 16:05 An: The Pacemaker cluster resource manager Betreff: Re: [Pacemaker] cluster heartbeat is not used because in your corosync-cfgtool -s you are using bonding address 2013/12/9 Dvorak Andreas <andreas.dvo...@baaderbank.de<mailto:andreas.dvo...@baaderbank.de>> Hi Here it is cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: em3 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: em3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: c8:1f:66:d7:3b:fe Slave queue ID: 0 Slave Interface: p3p3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:0a:f7:3e:ca:8e Slave queue ID: 0 Andreas Von: emmanuel segura [mailto:emi2f...@gmail.com<mailto:emi2f...@gmail.com>] Gesendet: Montag, 9. Dezember 2013 15:50 An: The Pacemaker cluster resource manager Betreff: Re: [Pacemaker] cluster heartbeat is not used show cat /proc/net/bonding/bond0 2013/12/9 Dvorak Andreas <andreas.dvo...@baaderbank.de<mailto:andreas.dvo...@baaderbank.de>> Dear all, during failover tests I found out that I can put down the heartbeat interfaces and the cluster ignores that. But if I put down bond0 the fencing is running. Can please somebody help me? bond0 Link encap:Ethernet HWaddr C8:1F:66:D7:3B:FE inet addr:10.15.28.36 Bcast:10.15.255.255 Mask:255.255.0.0 inet6 addr: fe80::ca1f:66ff:fed7:3bfe/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 em4 Link encap:Ethernet HWaddr C8:1F:66:D7:3B:FF inet addr:192.168.2.36 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::ca1f:66ff:fed7:3bff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p3p4 Link encap:Ethernet HWaddr 00:0A:F7:3E:CA:8F inet addr:192.168.3.36 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::20a:f7ff:fe3e:ca8f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 I have the following corosync.conf # Please read the corosync.conf.5 manual page compatibility: whitetank totem { version: 2 secauth: off threads: 0 interface { ringnumber: 0 bindnetaddr: 192.168.2.0 mcastaddr: 226.94.1.1 mcastport: 5405 ttl: 1 } interface { ringnumber: 1 bindnetaddr: 192.168.3.0 mcastaddr: 226.94.1.2 mcastport: 5407 ttl: 1 } } logging { fileline: off to_stderr: no to_logfile: yes to_syslog: yes logfile: /var/log/cluster/corosync.log debug: off timestamp: on logger_subsys { subsys: AMF debug: off } } amf { mode: disabled } I have installed cluster-glue-libs.1.0.5.x86_64.CentOS corosynclib.1.4.1.x86_64.CentOS openais.1.1.1.x86_64.CentOS cman.3.0.12.1.x86_64.CentOS pacemaker-libs.1.1.8.x86_64.CentOS resource-agents.3.9.2.x86_64.CentOS corosync.1.4.1.x86_64.CentOS modcluster.0.16.2.x86_64.CentOS openaislib.1.1.1.x86_64.CentOS pacemaker-cluster-libs.1.1.8.x86_64.CentOS pacemaker.1.1.8.x86_64.CentOS pcs.0.9.26.noarch.CentOS libqb.0.14.2.x86_64.CentOS clusterlib.3.0.12.1.x86_64.CentOS ricci.0.16.2.x86_64.CentOS pacemaker-cli.1.1.8.x86_64.CentOS fence-virt.0.2.3.x86_64.CentOS ccs.0.16.2.x86_64.CentOS # corosync-cfgtool -s Printing ring status. Local node ID 1 RING ID 0 id = 10.15.28.36 status = ring 0 active with no faults # pcs status corosync Nodeid Name 1 sv2836.muc.baag 2 sv2837.muc.baag # crm_mon --one-shot -V Last updated: Mon Dec 9 14:56:32 2013 Last change: Mon Dec 9 14:07:03 2013 via cibadmin on sv2836 Stack: cman Current DC: sv2836 - partition with quorum Version: 1.1.10-1.el6_4.4-368c726 2 Nodes configured 4 Resources configured Online: [ sv2836 sv2837 ] ClusterIP (ocf::heartbeat:IPaddr2): Started sv2836 FIXRoute (ocf::baader:FIXRoute): Started sv2836 ipmi-fencing-sv2837 (stonith:fence_ipmilan): Started sv2836 ipmi-fencing-sv2836 (stonith:fence_ipmilan): Started sv2837 Best regards Andreas Dvorak _______________________________________________ Pacemaker mailing list: Pacemaker@oss.clusterlabs.org<mailto:Pacemaker@oss.clusterlabs.org> http://oss.clusterlabs.org/mailman/listinfo/pacemaker Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf Bugs: http://bugs.clusterlabs.org -- esta es mi vida e me la vivo hasta que dios quiera _______________________________________________ Pacemaker mailing list: Pacemaker@oss.clusterlabs.org<mailto:Pacemaker@oss.clusterlabs.org> http://oss.clusterlabs.org/mailman/listinfo/pacemaker Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf Bugs: http://bugs.clusterlabs.org -- esta es mi vida e me la vivo hasta que dios quiera
_______________________________________________ Pacemaker mailing list: Pacemaker@oss.clusterlabs.org http://oss.clusterlabs.org/mailman/listinfo/pacemaker Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf Bugs: http://bugs.clusterlabs.org